2. A ball of mass 5.0 kg is suspended by two wires from a horizontal arm that is attached to a vertical shaft, as shown in the figure. The shaft is in uniform rotation about its axis. The rate of rotation is adjusted until the tensions in the two wires are EQUAL. At that speed, what is the radial acceleration of the ball? 0.80 m 10 m 0.60 m Ball

2. A ball of mass 5.0 kg is suspended by two wires from a horizontal arm that is attached to a vertical shaft, as shown in the figure. The shaft is in uniform rotation about its axis. The rate of rotation is adjusted until the tensions in the two wires are EQUAL. At that speed, what is the radial acceleration of the ball? 0.80 m 10 m 0.60 m Ball

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.78P: The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016,...

See similar textbooks

Similar questions

weighs 60 N on Earth. (3). A system consists of a pulley (vertical wheel) that is only allowed to rotate (spin). A cord is passed over the pulley and at each end there is a mass attached to the end of the cord. The mass attached on the left is m, =0.6 kg and at the right the mass is m2 = 0.8 kg. a) Calculate both the Tension in the cord and the acceleration of the system. b) What are the accelerations of both masses, if you were to cut the cord? Neglect the friction between cord and wheel,
Three friends ride a Ferris wheel with a diameter of 76m. Their combined mass with each car of the Ferris wheel is 389kg. When their car is at position A, the steel support applies 503N force at the car at an angle of 40degrees with the horizontal. What is the speed of the cars?
Two box hang from the ends of a string suspended from a frictionless pulley. The mass on the left is chosen to create a tension of 4 N in the string. The box on the right has a weight of 2 N. What will be the acceleration of the box on the right? Assume the acceleration of gravity is 9.8 m/s?. 4 N 2 N
A car weighs 150 kilograms with a center mass at G. The horizon force P= 600 newton’s. Please find the normal force of every wheel and the change in velocity. Please draw the free body diagram if necessary. Please refer to illustration. Thank you. G 1.25 m P = 600 N %3D 0.25 m 0.25 m 0.5 m -1.25 m |0.75 m
If the maximum length of the spring is 40 cm, what average friction force opposes the motion of the mass?
1. A wire is connected from a support at ri = (0, 2.0, 8.0) meters to an object of mass 45 kg at r2 (5.5, 4.3, 3.2) meters. Find the tension in the wire, expressed as both x, y, and z components and as a magnitude and direction relative to the hanging mass. Take the acceleration due to gravity as acting in the negative k direction, i.e a = (0, 0, -g).
A uniform rod of mass M = 2.3 kg and length L = 0.2 m, lying on a frictionless horizontal plane, is free to pivot about a vertical axis through one end, as shown. The moment of inertia of the rod about this axis is given by 1/3 ML2. If a force F = 7 N, q = 47° acts as shown, what is the resulting angular acceleration (in rad/s2) about the pivot point?
A 6-m long ladder has a mass of 13 kg., and its center of gravity is 2.4 m from the bottom along the ladder. The ladder is resting on a 5° upward sloping floor at A and on a wall inclined to the right at 5° from the vertical at B, so that it makes an angle of 60° with the horizontal. How far up along the ladder can a 78-kg man climb before the ladder is on the verge of slipping? The angle of friction at all contact surfaces is 15°. Also determine the total reaction at A and B in Newton. Note: Point A is at the left of point B.
A block and sphere are connected by a cord that passes over a pulley as shown. Neglect friction and assume the cord is massless. Take m₁ = 2.00 kg, m₂ = 5.45 kg, and 8 = 48.5⁰. m₂ m₂ (a) What are the magnitude of acceleration (in m/s2) of the block and sphere? m/s² (b) What is the tension (in N) in the cord? (Enter the magnitude.) N (c) What is the speed (in m/s) of each object 2.50 s after being released from rest? m/s (d) What If? If the incline under m₂ is rough, what is the minimum value of the coefficient of static friction for which the system will not move? Ms=
A 10000N weight is to be lowered by a vertical cylinder as shown in Figure . The cylinder hasa 75−mm−diameter piston and a 50−mm− diameter rod. The weight is to decelerate from100m/min to stop in 0.5s. Determine the required pressure in the rod end of the cylinderduring the deceleration motion.
1,V 3 46| Asiacell K/s the system blocks shown below is in equilibrium, the weight of block A is 10 kN and for block B is 35 kN . The coefficient of friction between A and surface is 0.2 and between two block :A and B is 0.15. Answer the following P=40KN الخيار رقم 1 5 نقاط The direction of friction force between two blocks which * effect on block A is in First Quarter Second Quarter Third Quarter Fourth Quarter
A weight with mass mw=150 g is tied to a piece of thread wrapped around a spool, which is suspended in such a way that it can rotate freely. When the weight is released, it accelerates toward the floor as the thread unwinds. Assume that the spool can be treated as a uniform solid cylinder of radius R=4.00 cm and mass Ms=200 g. Find the magnitude ?a of the acceleration of the weight as it descends. Assume the thread has negligible mass and does not slip or stretch as it unwinds. Use ?=9.81 m/s2. Find the tension T in the thread.