3.10 A total of 24 MHz of bandwidth is allocated to a particular FDD cellular telephone system that uses two 30 kHz simplex channels to provide full duplex voice and control channels. Assume each cell phone user generates 0.1 Erlangs of traffic. Assume Erlang B is used. (a) Find the number of channels in each cell for a four-cell reuse system. (b) If each cell is to offer capacity that is 90% of perfect scheduling, find the maximum number of users that can be supported per cell where omnidirectional antennas are used at each base station. (c) What is the blocking probability of the system in (b) when the maximum number of users are available in the user pool?

3.10 A total of 24 MHz of bandwidth is allocated to a particular FDD cellular telephone system that uses two 30 kHz simplex channels to provide full duplex voice and control channels. Assume each cell phone user generates 0.1 Erlangs of traffic. Assume Erlang B is used. (a) Find the number of channels in each cell for a four-cell reuse system. (b) If each cell is to offer capacity that is 90% of perfect scheduling, find the maximum number of users that can be supported per cell where omnidirectional antennas are used at each base station. (c) What is the blocking probability of the system in (b) when the maximum number of users are available in the user pool?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. Are the following statements correct or wrong? (a) Thyristors are used only for low voltage, low current applications. (b) MOSFETs are used for high frequency applications. (c) BJT is more efficient than IGBT in high power applications. (d) GTO requires very low current applied to its gate to be turn off. (e) IGBT is a voltage driven device. 2. Are the following statements correct or wrong? (a) Thyristors are preferred to be used in the output stage of 10W IMHz transmitter. (b) MOSFETs are preferred to be used for 1000 kW motor control circuit. (c) TRIAC is used for lighting dimmer circuits. (d) IGBT in high voltage de rectifier circuits (above 5kV level). (e) BJT is the fastest switching device in power applications. Choose the correct answer for the following questions (3-7): 3. The conditions which must be satisfied to turn on the thyristor with its current is more than its latching current are: (a) The anode is more positive than the cathode and a positive current pulse is…
1. Are the following statements correct or wrong? (a) Thyristors are used only for low voltage, low current applications. (b) MOSFETs are used for high frequency applications. (c) BJT is more efficient than IGBT in high power applications. (d) GTO requires very low current applied to its gate to be turn off. (e) IGBT is a voltage driven device. 2. Are the following statements correct or wrong? (a) Thyristors are preferred to be used in the output stage of 10W IMHz transmitter. (b) MOSFETs are preferred to be used for 1000 kW motor control circuit. (c) TRIAC is used for lighting dimmer circuits. (d) IGBT in high voltage de rectifier circuits (above 5kV level). (e) BJT is the fastest switching device in power applications. Choose the correct answer for the following questions (3-7): 3. The conditions which must be satisfied to turn on the thyristor with its current is more than its latching current are: (a) The anode is more positive than the cathode and a positive current pulse is…
Q4/ Why the performance of multimode graded index is better than multimode step index? Q5/ Design fiber optics communication system with analogue input and then measure the performance of the three types of fiber optics configurations. After that, answer the following questions: 1. Which configuration is the better? Comment! 2. Which parameters that improve the performance of multimode step index? Comment! 3. Which parameters that improve the performance of multimode graded index? Comment! 4. Which parameters that improve the performance of single mode step index? Comment! 5. If we need to increase the fiber length from 1 km to 15 km. which configuration is used? Comment!
(a) Explain the main different between a 2-bit asynchronous counter and a frequency divider by 4 with the aid of appropriate diagram. (b) Determine the sequence of the counter shown in Figure 7 and explain the function of NAND gate in the circuit. Begin with the condition that the counter is cleared. Show the appropriate waveforms for all input and outputs to support your answer using the answer sheet provided in Appendix. Do D D2 CLK Figure 7 |Rajah 7) (c) Design a synchronous counter that can count up and down for a sequence of 3+2+»5+>1 using D flip-flops.
We want to design a digital circuit that converts Gray code (ABC) to Binary code (xyz). Set up a 8-to- 1 line multiplexer so that the output gives y as a function of ABC. "A" is given to the most significant bit of the control inputs of the multiplexer. "C" is given to the least significant bit of the control inputs of the multiplexer.
Are the following statements correct or wrong? Justify your answer. GTO requires very low current applied to its gate to be turn off. IGBT is a voltage driven device. BJT is more efficient than IGBT in high power applications. Thyristors are used only for low voltage, low current applications. MOSFETs are used for high frequency applications.
د تعديل 4. Are the following statements correct or wrong? Justify your answer. (a) GTO requires very low current applied to its gate to be turn off. (b) IGBT is a voltage driven device. (c) BJT is more efficient than IGBT in high power applications. (d) Thyristors are used only for low voltage, low current applications. (e) MOSFETS are used for high frequency applications. تمويه رش الألوان فلتر اقتصاص تدوير
Suppose that the circuit shown in the below figure is to be modeled. What is the correct VHDL option for the synthesis of this circuit? global_resetb zb- global cik a
Q6: Sectoring is a way to do what? a. Achieve branch circuits. b. Put each phone call in a different time slot. c. Do SS7 look-ahead call placement. d. Partition Voice mail boxes e. It is an ISDN-PRI way of brining in trunks f. Achieve frequency reuse. g. None of the above
Determine the limits of region of operations of M1 for the device given in figure. Assume VDD = 2.5 V. Note: For respective enrolment number BT19ECEOXY If enrolment number is even, Consider |Vl = |Vpl = 0.X V %3D %3D If enrolment number is odd, Consider IVtnl = IVtpl = 0.Y V %3D If X is odd, V1 is linearly increasing from 0 to VDD If X is even, V1 is linearly decreasing from VDD to 0. VpD
Select the correct answer5. In a digital communication system, regarding the effect on the probability of error, it is not relevant to seek ..A. one channel without distortion.B. a good SNR.C. a channel without noise.D. high fidelity of the signals.
Q.1) What is the type of PCI transaction diagram? Redraw the timing when the IRDY# and TRDY# is ready from cycle 2 to end of transaction and explained the function of each signals appear in diagram. CLK FRAMEN AD Address Data-1 Data-2> Data-3 C/BE# Bus Cmd BE# IRDY# TRDYW DEVSEL# Data Phase Data Data Address Phase Phase Phase