3.18 The solid compound shaft, made of three different materials, carries the two torques shown. (a) Calculate the maximum shear stress in each material. (b) Find the angle of rotation of the free end of the shaft. The shear moduli are 28 GPa for alu- minum, 83 GPa for steel, and 35 GPa for bronze. 1.5 kN • m 4 kN • m Steel Aluminum Bronze J00 mm 75 pums e- 3 m- -2 m 1.5 m→

3.18 The solid compound shaft, made of three different materials, carries the two torques shown. (a) Calculate the maximum shear stress in each material. (b) Find the angle of rotation of the free end of the shaft. The shear moduli are 28 GPa for alu- minum, 83 GPa for steel, and 35 GPa for bronze. 1.5 kN • m 4 kN • m Steel Aluminum Bronze J00 mm 75 pums e- 3 m- -2 m 1.5 m→

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3.22 The compound shaft, composed of steel, aluminum, and bronze segments, carries the two torques shown in the figure. If Tc = 250 lb- ft, determine the max- imum shear stress developed in each material. The moduli of rigidity for steel, alu- minum, and bronze are 12 × 10° psi, 4 × 10° psi, and 6 × 10° psi, respectively. %3D 500 lb · ft | Steel 1.0 in. Aluminum | 2 in. Bronze $1.0 in. B D C 6 ft →le 4 ft →l– 3 ft –
1. A shaft 80 mm diameter transmits power at maximum shear stress of 63 MPa. Find the length of a 20mm wide key required to mount a pulley on the shaft so that the stress in the key does not exceed 42 MPa.
A ship's propeller shaft is 5 inches in diameter. The thrust load is 12,000 lb and the torque is 150,000 in - lb. Determine the resultant maximum shearing and compressive ( tensile ) stresses.
3.34 The steel shaft with two different diameters rotates at 4 Hz. The power sup- plied to gear C is 55 kW, of which 35 kW is removed by gear A and 20 kW is re- moved by gear B. Find (a) the maximum shear stress in the shaft; and (b) the angle of rotation of gear A relative to gear C. Use G = 83 GPa for steel. 55 mm B 65 mm C 4 m t 2 m→|
Determine the torsional shear stress in the shaft section AB and BC. There is a fixed support at C that can resist a moment. (Image taken from Statics and Mechanics of Materials by Beer, Johnson, DeWolf and Mazurek) T₁ = 300 N-m 30 mm TB = 400 N-m 46 mm 055 Shear Stress in AB = Shear Stress in BC= B 0.9 m 0.75 m units: units:
5) Find the maximum shear stress in each shaft for the following arrangement. Assume the diameter value of all shafts is same (50 mm) and material is steel (G-85 GPa) Dimensions in mm 40 500 Nm
A solid shaft in a rolling mill transmits 20 kW at 2 revolutions per second. The length of the shaft is 3 m and modulus of rigidity is 83,000 MPa. Which of the following gives the torque carried by the shaft?a. 1.59 kN-m c. 2.69 kN-mb. 3.45 kN-m d. 4.81 kN-m Which of the following gives the minimum diameter so that the allowable torsional shearing of 40 MPa will not beexceeded?a. 88 mm c. 59 mmb. 45 mm d. 76 mm Which of the following gives the minimum diameter so that the allowable angle of twist of 6O will not be exceeded?a. 29 mm c. 35 mmb. 49 mm d. 55 mm
1.A hollow steel shaft transmits 600 kW at 500 r.p.m. The maximum shear stress is 62.4 MPa. Find the outside and inside diameter of the shaft, if the outer diameter is twice of inside diameter, assuming that the maximum torque is 20% greater than the mean torque. 2. A motor car shaft consists of a steel tube 30 mm internal diameter and 4 mm thick. The engine develops 10 kW at 2000 r.p.m. Find the maximum shear stress in the tube when the power is transmitted through a 4 : 1 gearing. 3.A line shaft rotating at 200 r.p.m. is to transmit 20 kW. The allowable shear stress for the material ofthe shaft is 42 MPa. If the shaft carries a central load of 900 N and is simply supported between bearing 3 metre apart, determine the diameter of the shaft. The maximum tensile or compressive stress is not to exceed 56 MPa. 4.A cast gear wheel is driven by a pinion and transmits 100 kW at 375 r.p.m. The gear has 200 machine cut teeth having 20° pressure angle and is mounted at the centre of a 0.4 m…
A Solid shaft transmits 600 N.m torque. If the maximum shear stress induced in the shaft is 50 N/mm2, the minimum diameter of the shaft is
The maximum torsional shear stress of a shaft with diameter D can be found at what distance from the center of the shaft?
1.5 kN 120 mm Outer diameter: 72 mm Inner diameter: 62 mm 150 mm D 120 mm 4.5 kN A For element A find: (a) Torsional shearing stress (b) Transverse shear stress (c) Normal stress Q = [AS] × y 2rm TU y =
3.13 The torques T and 2T are carried by a shaft consisting of steel and aluminum segments. If the working shear stresses are 14 000 psi for steel and 7500 psi for aluminum, and the angle of rotation at the free end must not exceed 8, find the largest allowable value of T. For steel, use G = 12 x10^6 psi, and for aluminum, use G = 4 x10^6psi. T Aluminum 1.5 in.- 27/ Steel 2 in. + گری برای Happy 2 ft 3 ft as 3.14 T angle showr