Q3 Two shaft is attached to a rigid wall at each end. For the bronze segment AB. the diameter is 75 mm and G- 35 GPa. For the steel segment BC, the diameter is 55 mm and G= 83 GPa Given that a-2 m and b-1.5 m. compute the largest torque T that can be applied as shown in the figure if the maximum shear stress is limited to 60 MPa in the bronze and 80 MPa in the steel Bronze Steel

Q3 Two shaft is attached to a rigid wall at each end. For the bronze segment AB. the diameter is 75 mm and G- 35 GPa. For the steel segment BC, the diameter is 55 mm and G= 83 GPa Given that a-2 m and b-1.5 m. compute the largest torque T that can be applied as shown in the figure if the maximum shear stress is limited to 60 MPa in the bronze and 80 MPa in the steel Bronze Steel

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.8.3P: A solid circular shaft AB of diameter d is fixed against rotation at both ends (sec figure), A...

See similar textbooks

Similar questions

A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions shown in the figure. The magnitudes of the torques are T1= 1000 lb-in., T2= T4= 500 lb-in., and T3= T5= 800 lb-in. The tube has an outside diameter of d2= 1.0 in. The allowable shear stress is 12,000 psi and the allowable rate of twist is 2.0°/ft. Determine the maximum permissible inside diameter d1, of the tube.
A solid circular shaft AB of diameter d is fixed against rotation at both ends (sec figure), A circular disk is attached to the shaft at the location shown. What is the largest permissible angle of rotation 0max of the disk if the allowable shear stress in the shaft is Tallow? [Assume that a >b. Also, use Eqs. (3-50a and b) of Example 3-9 to obtain the reactive torques.]
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 75 mm and G = 35 GPa. For the steel segment BC, the diameter is 50 mm and G = 83 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torque T in kN-m that can be applied as shown in the figure if the maximum shear stress is limited to 60 MPa in the bronze and 80 MPa in the steel. Answer in 2 decimal places
he compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 75 mm and G = 35 GPa. For the steel segment BC, the diameter is 50 mm and G = 83 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torque T in kN-m that can be applied as shown in the figure if the maximum shear stress is limited to 60 MPa in the bronze and 80 MPa in the steel.
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 70 mm and G = 33.29 GPa. For the steel segment BC, the diameter is 40 mm and G = 84.85 GPa. Given that a = 2.03 m and b = 1.38 m, compute the largest torque T (in Nm) that can be applied as shown in the figure if the maximum shear stress is limited to 64.59 MPa in the bronze and 84.39 MPa in the steel. Round off the final answer to two decimal places. d A Bronze B Steel b. Add your answer
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 68 mm and G = 34.84 GPa. For the steel segment BC, the diameter is 40 mm and G = 83.59 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torque T (in Nm) that can be applied as shown in the figure if the maximum shear stress is limited to 69.92 MPa in the bronze and 87.06 MPa in the steel. Round off the final answer to two decimal places. d ... A Bronze B Steel b.
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 66 mm and G = 33.38 GPa. For the steel segment BC, the diameter is 40 mm and G = 83.55 GPa. Given that a = 2.12 m and b = 1.44 m, compute the largest torque T (in Nm) that can be applied as shown in the figure if the maximum shear stress is limited to 66.04 MPa in the bronze and 81.48 MPa in the steel. Round off the final answer to two decimal places.
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 66 mm and G = 34.74 GPa. For the steel segment BC, the diameter is 45 mm and 6 = 84.1 GPa. Given that a = 2.18 m and b = 1.43 m, compute the largest torque T (in Nm) that can be applied as shown in the figure if the maximum shear stress is limited to 65.48 MPa in the bronze and 81.24 MPa in the steel. Round off the final answer to two decimal places. d ... A Bronze B Steel b–
A metal shaft ABCD with variable cross-section is subjected to three external torques (T₁=28 kip- in, T2=8 kip-in, and T3=10 kip-in) as shown in the figure below. Each torque is acting at the locations marked with circular points along the shaft. Note that a 16-inch long segment of the shaft at the free end (right) has a 1-inch diameter bore. The dimensions (lengths and diameters) of the shaft are given in the figure. Assume deformation is linear elastic and take G=12×106 psi. D [3" 16"- X C T₁ 2" -32"- T₂ 1" diam. bore B -16"- A T3 the bar has a uniform diameter d along its full length, but external torques remain the same and are applied at the same locations. If the failure shear stress for the material is equal to Tfail = 10 ksi, and the factor of safety is equal to 2, determine the required (uniform) diameter d for the bar. Assume that the bar is solid for its entire length.
The solid-circular member AC, having a diameter D and a shear modulus of 69 GPa, is subjected to the torques 2T and 3T at points A and B, respectively. If Tallow = 35 MPa and (OA/c)allow =2°. detemine the maximum pemissible value of the torque T. Use the table given below and your student ID to find the values of L1, L2, and D. B A 3T 2T Student L1 (m) L2 (m) D ID (mm) 1131731 1 0.6 78
The aluminum shaft, composed of three segments is fastened to rigid supports as A and D. Calculate the maximum shear stress in each segment when the two torques are applied. A 400 N-m 850 N-m L=1.4 m 30 mm diameter B L=2.4 m 50 mm diameter L-1.9 m 30 mm diameter
A solid shaft 100 mm in diameter is subjected to an axial compressive load of 600 kN simultaneously with a torque that twists the shaft thru an angle of 1.5 degrees in the length of 8 meters. If G=80Gpa, compute the maximum normal stress in the shaft. This is a COMBINED STRESS problem. Please include drawings of the circle.