32. The balanced A-connected load in Fig. 12.35 is demanding 10 kVA at a lagging PF of 0.91. If line losses are negligible, calculate IbB and Van if Vca=160/30° V and the source voltages are described using positive phase sequence.

32. The balanced A-connected load in Fig. 12.35 is demanding 10 kVA at a lagging PF of 0.91. If line losses are negligible, calculate IbB and Van if Vca=160/30° V and the source voltages are described using positive phase sequence.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.42P: A balanced -connected impedance load with (12+j9) per phase is supplied by a balanced three-phase...

See similar textbooks

Related questions

Q: Determine: Pt, Rt, It and Voltage across each load is the voltage supply is 250V

A: In this question, we need to determine the total power, total current, total resistance and voltage…

Q: Find the branch currents i1, i2, and i3 in the circuit in figure mentioned below if v1 = 70V and v2…

A: The given circuit isv1 = 70V and v2 = 40V.We need to find the currents i1, i2 and i3.

Q: Apply the gain formula to the SFGs shown in Fig. Y Y Y₂Y₂ Y Y Y Y₂ to find the following transfer…

A: Mason's Gain Formula, also known as the Mason's Rule or the Signal Flow Graph (SFG) Gain Formula, is…

Q: The rated frequency of squirrel cage motor is 50 Hz. The synchronous rotation speed of the magnetic…

Q: Consider the figure shown below. Find the voltage (V) at node 1. V1 10V Qu'e 15 V شمشه O 12 V O 16 V…

Q: Find the transfer function, ?(?)=V0 (s)/Vi(s) of the network shown in the image:

Q: For the network shown in figure 1, find the transfer function G(s) = Vo (s) V{(s) vi(1)( I H -0000…

A: Given circuit:Asked to find the transfer function of the above circuit?

Q: The transistor in the amplifier circuit shown has k = 0.5 mA/V², VTH = -1 V and λ = 0. a. Construct…

A: Since you have posted a question with multiple sub parts and part (a) also contains multiple sub…

Q: What is the power dissipated in the 10 ohm resistor. HH 10.0 V www 3.00 Ω 6.00 V a) 9 x 10³ W b) 7.8…

Q: For this circuit, what is i(0+), the current through the inductor at time t = = 0+. X 1 H m 3 A a.…

A: According to the bartleby policy, we can solve only first question.Please post another question as…

Q: Determine y(t) 1) Y(s) = s+1/(s+2)(s+3) 2) Y(s) = s+3/(s+1)^2

A: Use the partial fraction method to solve the question Find the value of A and B

Q: 2. Determine Vo using: (a) Mesh Analysis; an d(b) Nodal Analysis.

A: For the given circuit the value of the unknown voltage needs to be calculated by using mesh analysis…

Q: 2A V 10 ohm T 8A

A: The question is about finding the current and voltage in the circuit.

Q: On the circuit show below, determine: Voltages V1 and V2 Currents through each of the resistors…

A: For the given circuit calculation of:Voltages V1 and V2.Current across each resistors.Voltage across…

Q: I don't understand where you got -553 kHz and -547kHz. Can you explain that? Also what are the…

A: Given:Solution of a DSB-SC modulation problem. Fourier transform of the signal x(t) is,where…

Q: The transistor in the amplifier circuit shown has k = 0.5 mA/V², VTH = -1 V and λ = 0. a. Construct…

A: Since you have posted a question with multiple sub parts and part (a) also contains multiple sub…

Q: Use the node-voltage method to find the voltages shown, v1, v2, and v3.

A: For the given circuit the unknown voltages need to be calculated by using the nodal analysis and the…

Q: Analyze the challenges of implementing wireless power transmission technologies and their potential…

A: Implementing wireless power transmission technologies presents exciting opportunities but also comes…

Q: the Total Resistance is found to be 6 Ohms. FIND The required Voltage Source E The value of R2

A: In this question, we need to determine the value of resistance R2 and value of voltage source E.…

Q: - To find a Io, use a Source Transformation ww 4 ΚΩ 2 ΚΩ Σ 2 mA 6V • 2 ΚΩ Το 6 ΚΩ +)3v

A: In this question, we need to determine the value of current Io using the source transformation.

Q: 4) Determine the shown below gain and bandwidth for the circuit. RF $330k Rs = 10K 22 15MH₂ f

A: We need to find out the gain and bandwidth for given opamp .

Q: system are given below: i(t) i₁(t)/ i(t) =ii(t) + i2(t) dv(t) dt i₂(t) = = R Show that the…

A: Given Data:An RLC circuit with the system of equations as,Supply current, Capacitor voltage,…

Q: Discuss the various types of integrated circuits (ICs) and components offered by Microchip for…

A: Integrated Circuits (ICs), also commonly known as microchips or chips, are a fundamental component…

Q: Can you please explain the steps on how to solve for equations lll, IV, and V to get the current…

A: The question is about finding currents.

Q: Use superposition to solve for io and vo in the circuit

A: In the given circuit the value of the unknown voltage and current needs to be calculated by using…

Q: Consider the given circuit. C V b cn 2 n Vbn Rw www an Rw www a C °V. B °V. Zp V. Rw ww N Each…

Q: E = 12 V / 0° Z₁ = |= 4₁= 1₂= 13 = VL= + + V₂ voo X₂ = 60 1₁ ~) ZT +₁₁ 2 N N N Z N Xc₁ Xc₂ 8 Ω 1₂ 12…

Q: Consider an oscillating magnetic dipole with magnetic dipole moment m = moe it. Calculate the…

Q: Consider a simple positive phase sequence, three-phase, three-wire system operated at 50 Hz and with…

A: In this question, we need to determine the power supplied by the three-phase source. Three phase…

Q: Find the area under the function shown in the following figure: f(t) 1/E - 01 (a) (a) What is the…

A: The triangular pulse extends from −ϵ to +ϵ. Therefore, the duration (or width) of the function is…

Q: 9)The........and the ........are very similar a)engineer's scale rule and architect's scale rule b)…

A: We need to select correct option for given Statement.

Q: Express Vo as V₁, V2, V3. describe the process of calculation R₁ www DIO U₂ 0 13 O R₂ M R3 R4 WWW ww…

A: The given circuit isWe need to express vo as v1, v2 and v3.

Q: What are the gain, input resistance, and output resistance for the circuits in the given figure…

A: An operational amplifier, often abbreviated as op-amp, is a versatile and widely used electronic…

Q: For question 1, The instructor asked what is an approach to modulate a PWM signal and what is an…

A: According to the question, we need to explain one approach for PWM modulation and detection…

Q: 1. KVL and Ohm's Law: Find the current, I, and voltages, V₁, V2, V3, V4, Vs and Vab in the following…

Q: Consider the two signals c₁(t) = 4 cos(50000πt) and c₂(t) = 4 sin(50000πt). The real and the…

A: Given:Real and imaginary parts of the spectrums of the two signals m1(t) and m2(t),Carrier signals…

Q: Question #5 y(t) Answer: 1.4 1.2 0.8 0.6 0.4 0.2 0 1 0 5 t (sec) A periodic signal has the waveform…

Q: For system 3, which graph shows the best memoryless, causality, linearity. Graphs can be chosen more…

A: Input output sequences for a DT sequence, we need to determine which graph from the above shown…

Q: In the circuit of Fig. 5.116, determine the maximum value of R2 that guarantees operation of Q1 in…

A: In the given questions we need to calculate the resistance R2.

Q: 40 w - - 1603 100 w 1201 140 w 50, $150 120 10 < 3 of 4 180 Part E Find the equivalent resistance…

A: In a series resistor configuration, resistors are connected end-to-end, and there is only one path…

Q: The op amp shown here operates from 19 V supplies and can produce no more than 15 mA of output…

A: Given:an op-amp circuit,with and it operates at supplies. The given circuit can not produce more…

Q: How would you reduce Req of a circuit by adding a resistor – numerical piece to follow.

Q: An NMOS device is operating in the triode mode. This means that: VGS > Vt and VDS > Vt VGS > Vt and…

A: We need to select correct option to MOSFET in triode region.

Q: how did you find Rth?

Q: 3 Problem #6 In the circuit shown find Vo in terms of V₁ and V₂ t R₁ R₁ Rz R₂ R3 RG

Q: Provide an overview of the history and evolution of microchips in the field of electronics.

A: The history and evolution of microchips in the field of electronics have been marked by significant…

Q: A dead battery is charged by connecting it to the live battery of another car with jumper cables…

A: The question is about finding currents in the circuit.

Q: Consider two voltage dividers shown in (Figure 1). Suppose that v=361 V. Figure 75 k a 25k0 a' b'e…

Q: Problem 1 Consider an RLC circuit driven by a programmable current source i(t) as shown in the…

A: The question is about finding transfer function.

Q: Explain the significance of microchips in the context of modern electronics and their role in…

A: Microchips, also known as integrated circuits or ICs, are fundamental components of modern…

Concept explainers

Single Phase AC Circuit

Alternating Current (AC) is a type of electric power in which the electric current changes, both in magnitude and direction, at regular intervals. This AC Circuits can deliver power in either a Single Phase system or a Three Phase system.

Question

V
b
cn
2
n
Vbn
Van
12+
FIGURE 12.35
a
Rw
www
Rw
Rw
P
B
Z p
2
Up
32. The balanced A-connected load in Fig. 12.35 is demanding 10 kVA at a
lagging PF of 0.91. If line losses are negligible, calculate IbB and Van if
V ca 160/30° V and the source voltages are described using positive phase
=
sequence.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given that

Step 2: Continue

Step 3: Continue

Solution

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Analysis of Single Phase and Three Phase System

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

1. Given the circuit below, the phase voltages are given by Van = 20040° Vrms. The source impedance is 5 + j7 per phase and the wire impedance is 8 +j10 per phase. Let the load impedance be Zy = 50 ohms. Find: Van Vin Ven a. II, and Ic b. c. VAN, VBN, and VCN, and VAB, VBC, and VCA Z₂ Z₂ Z₂ Zw Zw Zw B C le N
Problem 4- A large 3-phase industrial load draws 3.6 MVA at 0.85 power factor lagging from through a three- phase 12.47/7.2 kV 3-wire overhead distribution line. The phase conductor is #1 ACSR “Robin". Taking 3.6 MVA and 12.47 kV as base values, determine (a) The base impedance in (N) (b) The reactive power drawn by the load (p.u.) (c) The total current (p.u.) drawn from the power supply
2. A single-phase are distributor AB is fed from end A and has a total impedance of (0.3-0.3) ohm. At the far end, the voltage V-240V and the current is 100A at a p.f. of 0, 8 lagging. At the mid-point M. a current of 100 A is tapped at a p... of 0.6 lagging with reference to the voltage V_{M} at the midi-point. Calculate the supply voltage V Lambda j sending current I_{N} and the phase angle between V_{A} and V_{E}
Q2) A 13.2-kV single-phase generator supplies power to a load through a transmission line. The load's impedance is Ztoad 500 236.87° ohm , and the transmission line's impedance is Zine = 60 253.1° ohm. To reduce transmission line losses to 0.0103 of its losses without using the transformers design and use two transformers T1 between the generator and the transmission line and T2 between the transmission line and the load.
In a three-phase system voltage, assume that the phase-to-neutral voltage at phase “b” is considered as the reference (zero phase angle). 1. State the positive sequence and the negative sequence. 2. Solve the following for both sequences: a. the line-to-neutral voltages : VAN ,VBN and VCN b. the line-to-line voltages : VAB , VBC and VCA
For a balanced- load supplied by a balanced positive-sequence source. the line currents into the load are 3 times the -Ioad currents and lag by 30. (a) True (b) False
A balanced -connected impedance load with (12+j9) per phase is supplied by a balanced three-phase 60-Hz,208-V source, (a) Calculate the line current, the total real and reactive power absorbed by the load, the load power factor, and the apparent load power, (b) Sketch a phasor diagram showing the line currents, the line-to-line source voltages, and the -load currents. Use Vab as the reference.
The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
In a balanced three-phase Y-connected system with a positive-sequence source, the line-to-line voltages are 3 times the line-to-neutral voltages and lend by 30. (a) True (b) False
Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of the load impedance Z=ZZ, find expressions for P and Q, from complex power considerations. (b) Express p(t) in terms of P and Q, by choosing i(t)=2Icost. (c) For the case of Z=R+jL+1/jC, interpret the result of part (b) in terms of P,QL, and Qc. In particular, if 2LC=1, when the inductive and capacitive reactances cancel, comment on what happens.
A balanced three-phase load is connected to a 4.16-kV, three-phase, fourwire, grounded-wye dedicated distribution feeder. The load can be mode led by an impedance of ZL=(4.7+j9)/phase, wye-connected. The impedance of the phase conductors is (0.3+j1). Determine the following by using the phase A to neutral voltage as a reference and assume positive phase sequence: (a) Line currents for phases A, B, and C. (b) Line-to-neutral voltages for all three phases at the load. (c) Apparent. active, and reactive power dissipated per phase, and for all three phases in the load. (d) Active power losses per phase and for all three phases in the phase conductors.
Consider a 10 kVA, 200/400 V, 50 HZ: single-phase tranformer has the folloving test results:0.C. test: 200 V, 0.6A, 63 W (L.V.side)S.C. test : 20 V, 25A, 85 W (H.V. side)Deternine:i- The eficiengy at 75 % offiull-load at 0.9 leading power factor.ii -The secondary terminal voltage on fill-load at tunity power facton