BP2: A simply supported beam of constant El and length L is supporting a distributed load omega w overits entire span and a concentrated load F at x=L/3. F=wl. Determine the deflection of the beam at L/3using Catigliano's method.

Answered: Image /qna-images/answer/4d7992ad-df01-4ba0-9a4b-744357fb80ee.jpg

3P2: A simply supported beam of constant El and length L IS supporting a distributed load omega w over ts entire span and a concentrated load F at x=L/3. F=wl. Determine the deflection of the beam at L/3 using Catigliano's method.

3P2: A simply supported beam of constant El and length L IS supporting a distributed load omega w over ts entire span and a concentrated load F at x=L/3. F=wl. Determine the deflection of the beam at L/3 using Catigliano's method.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter9: Deflections Of Beams

Section: Chapter Questions

Problem 9.5.1P: A simply supported beam (E = 1600 ksi) is loaded by a triangular distributed load from A to C(see...

See similar textbooks

Related questions

Q: is the weight of a 10-pound mass at standard gravity in Newton, dynes and pound-force?

A: Given:m=10 lb

Q: A refrigeration plant comprises three evaporators of capacities 10 tonnes at 10°C, 20 tonnes at 5°C…

Q: 1. For o= 150 MPa and - 20 deg, the normal stress on inclined plane AB is best given by 145 MPa- b.…

Q: Problem 2. Amaterial element in plane stress is subjected to stresses: = -5000 psi Ox Oy = -2000 psi…

Q: A long, cylindrical, electrical heating element of diameter D = 14 mm, thermal conductivity k = 251…

A: Given data: D=14 mmk=251 W/m.Kρ=2805 kg/m3cp=903 J/kg.KT=30°CV=9 m/sq=1033 W/m Need to determine the…

Q: -) For the inverted manometer of Fig. 1, all fluids are at 20°C. If pB - pA = 97 kPa, what %3D must…

A: Given Pressure difference, PB - PA = 97 kPa Specific gravity of red oil, SG = 0.827…

Q: 2- Example: A bird flies east at 10m'sec for 100m. it then turns around and flies at 20m'sec for…

Q: model with k= 5/3. Ignore the effects of motion and gravity. Let T,=20 °C, Po=1 bar a) What are the…

Q: 0.4 m 0.6 m Fig. P3.48 0.3 m PROBLEM 3.48 The electric motor exerts a torque of 800 Nm on the steel…

Q: The displacement of a particle, moving in a straight line, is given by s = 2t + 2t +4 where s is in…

A: Given, Position of a particle as a function of time = s = (2t2 + 2t + 4) m Velocity (v) of the…

Q: Q19 For the plane wall shown in the figure (plane wall with heat source, one dimension and steady…

Q: Refrigerant 134a enters a compressor at 600 kPa as a saturated vapor. It exits at 60°C and 1.4 MPa.…

Q: edge of the Tami lam (x) = Alampª tur (æ) = Aturæb Alam = 1.98 = -0.5 Atur = 4.15 = -0,3 Calculate…

A: Calculated average heat transfer coefficient for laminar and turbulent conditions for plates of…

Q: A particle moves along a straight line such that its position is defined by s = (t2 – 6t + 5) m. -…

Q: Use one of the Numerical method: Newton-Raphson to find the maximum deflection and its location.…

A: Draw the free-body diagram. Apply force equilibrium in horizontal direction. HA=0 Apply moment…

Q: A particle moves along the path y = 4x, where x and y are in meters. The x coordinate of the…

Q: Compute the force in link AB of the lifting tongs which cross without touching. Ans. FAB = 1650 lb…

A: Weight of the load, W= 800 lb. Let FE be the vertical reaction at the point E. Let θ be the angle…

Q: A beam with a solid homogeneous rectangular section is simply supported at A and B. A concentrated…

Q: PROBLEM 3.54 The composite shaft shown consists of a 5 mm thick brass jacket (G = 39 GPa) bonded to…

A: Given: The shear modulus of the steel, Gs = 77 GPa The shear modulus of the brass, Gbr = 39 GPa The…

Q: A cylindrical object with a mass of m = 3.81 lbm slides into a pipe downward. The object has a…

Q: The bore diameter of each cylinder in a six-cylinder four-stroke petrol engine is 25 mm and the…

Q: A circular area of diameter d is vertical and submerged in a liquid. Its upper edge is coincident…

Q: Given the h and b with a radius of curvature of 104ft determine and normal force on a 30kg rider at…

Q: Two clean parallel glass plates, separated by a distance d = 1.5 mm, are dipped in a bath of water.…

Q: A rectangular bar having width w = 4.75 in. and thickness t = 2.00 in. is subjected to a tension…

Q: The rectangular bar has a width of w = 3.00 in. and a thickness of t = 1.50 in. The normal stress on…

Q: Q1) Propane gas (C3H8) is reacted with air in such a ratio that an analysis of the dry products of…

A: Given CO2 = 11.5% O2 = 2.7% CO = 0.7% To find Final Combustion equation Excess air percentage

Q: F6-15. If the beam is subjected to a bending moment of M = 20 kN m, determine the maximum bending…

A: Find the maximum bending stress.

Q: An 18 coils helical spring having a load of 100kg. The modulus of elasticity in shear of spring is…

A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked .…

Q: How does heat transfer over time ?

A: Heat transfer is the mode by which energy in the form of heat is transferred from one location to…

Q: The boy B jumps off the canoe at A with a velocity of VBJA = 4.5 m/s relative to the canoe as shown…

A: Given Angle = 30o Mass, MB = 30 kg MC = 40 kg MD = 25 kg Velocity, VBA =…

Q: Q18) The unit of Stefan - Boltzmann constant is: B) W/m . K A) m. K/ W C) W/m K D) W/m . K

A: This question is based on the concept of radiation and heat transfer.

Q: Show the Given, Diagram, Conversion 4, Solution Box Your Final Answer. Which component determines…

A: Given Diagram Point 4 characteristics Solution High pressure of Rankine cycle Low pressure of…

Q: A value has been measured by Instrument A imes with a standard deviation of 4.3. Anoth as been…

A: To given thatInstrument A , n1=33Instrument B , n2=7Standard deviation, S1=4.3Standard deviation,…

Q: Select the TRUE response. O a With increasing flow rate the friction factor of a given pipe…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Find the pressure at depth of 12 m in water Take density of water 1000 kg/m3

A: Given data: Density of water=ρ Acceleration due to gravity=g Depth=h Required : Pressure

Q: 8-25 A mass of 8 kg of helium undergoes a process from an initial state of 3 m/kg and 15°C to a…

Q: F6-17. If the beam is subjected to a bending moment of M = 50 kN m, determine the maximum bending…

A: Find the maximum bending stress.

Q: Discuss briefly with neat sketches the longitudinal transverse and torsional free vibrations.

A: INTRODUCTION : Vibration problems occur whenever there are rotating or moving elements in the…

Q: The flow rate of air moving through a square 0.50-m by 0.50-m duct is 160 m3/min. What is the mean…

Q: The 250-kg crate rests on the ground for which the coefficients of static and kinetic friction are u…

Q: A hydroelectric plant has a head of 57 m and a water volumetric flow rate of 500 m/s. Determine the…

Q: Q16) The thermal resistance of one layer plane wall is: C) (I/ri -- 1/r.) /4k A) AXKA B) In(r.…

A: This question is based on the concept of heat transfer and conduction.

Q: he flexural (or fracture) strength of brittle materials may be determined using a variation of…

A: calculat the caitical crack tip radius for we know that σm=2σ0aρt1/2 for [Al2O3] modulus of…

Q: A pump takes water at 60°F from a large reservoir and delivers it to the bottom of an open elevated…

Q: 6.33 A normal-shock inlet operates in a Mach 1.86 stream with ambient static pressure of Po = 30…

A: GIVEN:- M=1.86 P0=30KPA

Q: g. Water with x = 0 at P= 280 kPa. State the T and v of the system. h. Water at 350 kPa and 500°C.…

Q: 5. A9.0 m beam of uniform width is supported as shown by supports S1 and S2. Given the weight of the…

Q: e equation which gives differential equation free of parameters from two dimensiona n relations - +…

Q: The magnitude of the force is 8.3 N and the magnitude of the displacement is 8.0 m as shown. What is…

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

BP2: A simply supported beam of constant El and length L is supporting a distributed load omega w over
its entire span and a concentrated load F at x=L/3. F=wl. Determine the deflection of the beam at L/3
using Catigliano's method.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1- FBD and resolving of forces

VIEW

Step 2 - total strain energy

VIEW

Step 3- deflection at C

VIEW

Step 4

VIEW

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A simple beam with an overhang is subjected to d point load P = 6kN. If the maximum allowable deflect ion at point C is 0.5 mm, select the lightest W360 section from Table F-l{b) that can be used for the beam. Assume that L = 3 m and ignore the distributed weight of the beam.
Obtain a formula for the ratio c/maxof the deflection at the midpoint to the maximum deflection for a simple beam supporting a concentrated load P (see figure). From the formula, plot a graph of c/max versus the ratio a/L that defines the position of the load (0.5 < a/L < ) What conclusion do you draw from the graph? (Use the formulas of Example 9-3.)
The deflection curve for a cantilever beam AB (sec figure) is given by v=q0x2120LEI(10L210L2x+5Lx2x3) Describe the load acting on the beam.
-5-7 A cantilever beam AB carries three equalaly spaced concentrated loads, as shown in the figure. Obtain formulas for the angle of rotation B and deflaction B at the free end of the beam.
Copper beam AB has circular cross section with a radius of 0.25 in. and length L = 3 ft. The beam is subjected to a uniformly distributed load w = 3.5 lb/ft. Calculate the required load P at joint B so that the total deflection at joint B is zero. Assume that£ = 16,000 ksi.
A propped cantilever beam, fixed at the left-hand end A and simply supported at the right-hand end B, is subjected to a temperature differentia] with temperature T1on its upper surface and T2on its lower surface (see figure).
Obtain formulas for the angle of rotation 0Aat support A and the deflection SajAXat the midpoint for a simple beam AB with a uniform load of intensity q (see figure).
The wing of a small plane is represented by a simplified prismatic cantilever beam model acted on by the distributed loads shown in the figure. Assume constant El = 1200kN-m~, Find the tip deflection and rotation at B.
A cantilever beam has two triangular loads as shown in the figure. Find an expression for beam deflection Scusing Superposition. Find the required magnitude of load intensity q2in terms of q0so that the deflection at C is zero. Find an expression for the deflection at C if both load intensities, qxand q2, are equal to q0.
A cantilever beam model is often used to represent micro-clectrical-mechanical systems (MEMS) (sec figure}. The cantilever beam is made of polysilicon (E = 150 GPa) and is subjected to an electrostatic moment M applied at the end of the cantilever beam. 1 f dimensions arc h — 2 [im, h — 4 ^m, and L = 520 ^mt find expressions for the tip deflection and rotation of the cantilever beam in terms of moment M.
A propped cantilever steel beam is constructed from a W12 × 35 section. The beam is loaded by its self-weight with intensity q. The length of the beam is 1L5 ft. Let E = 30,000 ksi. Calculate the reactions at joints A and B. Find the location of zero moment within span AB. Calculate the maximum deflection of the beam and the rotation at joint B.
A cantilever beam has a length L = 12 ft and a rectangular cross section (b = 16 in., h = 24 in.), A linearly varying distributed load with peak intensity q0acts on the beam, (a) Find peak intensity q0if the deflection at joint B is known to be 0.18 in. Assume that modulus E = 30,000 ksi. (b) Find the location and magnitude of the maximum rotation of the beam.