5-120 Consider a 20-L evacuated rigid bottle that is surrounded by the atmosphere at 100 kPa and 27°C. A valve at the neck of the bottle is now opened and the atmospheric air is allowed to flow into the bottle. The air trapped in the bottle eventually reaches thermal equilibrium with the atmosphere as a result of heat transfer through the wall of the bottle. The valve remains open during the process so that the trapped air also reaches mechanical equilibrium with the atmosphere. Determine the net heat trans through the wall of the bottle during this filling process. Answer:= 2.0 kJ Air 20 L evacuated FIGURE P5-120 100 kPa 27°C

5-120 Consider a 20-L evacuated rigid bottle that is surrounded by the atmosphere at 100 kPa and 27°C. A valve at the neck of the bottle is now opened and the atmospheric air is allowed to flow into the bottle. The air trapped in the bottle eventually reaches thermal equilibrium with the atmosphere as a result of heat transfer through the wall of the bottle. The valve remains open during the process so that the trapped air also reaches mechanical equilibrium with the atmosphere. Determine the net heat trans through the wall of the bottle during this filling process. Answer:= 2.0 kJ Air 20 L evacuated FIGURE P5-120 100 kPa 27°C

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

This is the second part of a two-part problem. The piston/cylinder in the figure contains 0.5 kg of water with a pressure of P=250 kPa, and a specific internal energy of 2537.21 kJ/kg. The cylinder is connected by a valve (initially closed) to an empty tank with a volume of VT = 0.5 m³. The valve is opened and the water is heated to a final equilibrium temperature of 500°C in the combined piston/cylinder and tank system. What is the final volume in the piston/cylinder (not including the tank) in m3? Include 5 significant figures in your answer (5 decimal places). P=250 kPa u=2537.21 kJ/kg m=0.5 kg Piston/Cylinder- Valve 0 Tank V = 0.5 m
A rigid tank contains air at 500 kPa and 150°C. As a result of heat transfer to. the surroundings, the temperature and pressure inside the tank drop to 65°C and * ?400 kPa, respectively. the boundary work done during the process is positive negative zero non of the above
A piston–cylinder device, initially containing 0.25-kg steam at 3.5 MPa, is superheated by 4°C, i.e., the saturation temperature is raised by 4°C. Afterwards, the steam loses heat to the surroundings such that the piston moves down, hitting the stops; the cylinder contains saturated liquid water at this point. Hint: what is the type of boundary work done here? Is the work done by or done on the system? The cooling continues until the cylinder contains water at 205°C. Determine (a) the final pressure, in kPa, (b) the qualityat the final state, (b) the boundary work from state 1 to state 2, in kJ, (c) the amount of heat transferred when the piston first hits the stops, in kJ, (d) and the total amount of heat transferred for the system, in kJ. Is this heat added to or removed from the system?
This is the first part of a two-part problem. The piston/cylinder in the figure contains 0.5 kg of water with a pressure of P=250 kPa, and a specific internal energy of 2537.21 kJ/kg. The cylinder is connected by a valve (initially closed) to an empty tank with a volume of VT = 0.5 m³. What is the initial volume of water in the piston/cylinder in m³? Include 6 significant figures in your final answer (6 decimal places) and do not show include in the answer. P=250 kPa u=2537.21 kJ/kg m=0.5 kg Piston/Cylinder → Valve Tank- V = 0.5 m3
5-84 Hot exhaust gases of an internal combustion engine are to be used to produce saturated water vapor at 2 MPa pressure. The exhaust gases enter the heat exchanger at 400°C at a rate of 32 kg/min while water enters at 15°C. The heat exchanger is not well insulated, and it is estimated that 10 percent of heat given up by the exhaust gases is lost to the surroundings. If the mass flow rate of the exhaust gases is 15 times that of the water, determine (a) the temperature of the exhaust gases at the heat exchanger exit and (b) the rate of heat transfer to the water. Use the constant specific heat prop- erties of air for the exhaust gases. Exhaust gases 400°C Heat exchanger 2 MPa sat. vap. FIGURE P5-84 Water 15°C
A room is filled with saturated steam at 100°C. Now a 5-kg bowling ball at 25°C is brought to the room. Heat is transferred to the ball from the steam, and the temperature of the ball rises to 100°C while some steam condenses on the ball as it loses heat (but it still remains at 100°C). The specific heat of the ball can be taken to be 1.8 kJ/kg C. Solve for the mass of steam that condensed during this process.
An autoclave contains 1000 cans of pea soup. It is heated to an overall temperature of100C. If the cans are to be cooled to 40C before leaving the autoclave, how much coolingwater is required if it enters at 15C and leaves at 35C? The specific heats of the pea soupand the can metal are 4.1 kJ/kgC and 0.5 kJ/kgC, respectively. The weight of each can is60g and it contains 0.45 kg of pea soup. Assume that the heat content of the autoclave wallsabove 40C is 1.6x104 kJ and that there is no heat loss through the walls. Ans. 1,526.85 Kg
What is the specific internal energy of water at 50 kPa and 200°C?
Water is contained in the frictionless piston-cylinder device shown below. The device has stops that keep the piston a minimum distance from the bottom of the cylinder. Initially, the water is at 200°C and 600 kPa. The water is then cooled to 120°C, at which point the piston is resting on the stops and the volume of the water is half of its initial volume. The atmospheric pressure is 100 kPa and the piston has a radius of 5 cm. a. Create a schematic of the device and sketch the boundary around the system that you will use to solve the next parts of this problem. What is in your system? b. What kind of assumptions/observations can you make about this system that will be important for a thermodynamic analysis? c. While the piston moves, this process is iso______? Once the piston stops moving, this process is iso______? Explain. d. Draw this process on P-v and T-v diagrams. Clearly indicate the initial state, the "intermediate" state when the piston just meets the stops, and the final…
A cylinder container is divided into two equal sections by thermally isolated, frictionless piston, as shown in the figure. One section contains water and the other air. The cylinder is isolated except the one face of the water section. Each section has an initial volume of 100 liter. The initial temperature of the air is 40oC and the water is 90oC with steam quality of 10%. The water are heated slowly until the entire section of the water is filled with saturated steam. Find the final pressure and the amount of heat transported to the container. Assume: the heat transfer is a reversible process.Assume for ideal gas the following relation between p and v: #$" #$% !#" ! !" = ! "" ; k = 1.4
A container equipped with a resistance heater and amixer is initially filled with 3.6 kg of saturated watervapor at 120C. Now the heater and the mixture areturned on; the steam is compressed; and there is heatloss to the surrounding air. At the end of the process,the temperature and pressure of steam in thecontainer are measured to be 300C and 0.5MPa. Thenet energy transfer to the steam during this process is
5-100 A long roll of 2-m-wide and 0.5-cm-thick 1-Mn manganese steel plate (p = 7854 kg/m³ and cp = 0.434 kJ/kg-°C) coming off a furnace at 820°C is to be quenched in an oil bath at 45°C to a temperature of 51.1°C. If the metal sheet is moving at a steady velocity of 10 m/min, determine the required rate of heat removal from the oil to keep its temperature constant at 45°C. Answer: 4368 kW