8.6 - The three-phase wye-connected loads are in parallel across a three-phase supply. The firstload draws a current of 20 A at 0.9 power factor leading, and the second load draws a current of30 A at 0.8 power factor lagging. Calculate the following:a. The transmission line currentb. The power factor of the loadc. The real power supplied by the source if the line-to-line voltage of the transmission lineis 400V

a) load 1 power factor is leading that is current angle is positive hence ϕ1=cos−10.9 ϕ1=25.84o…

Answered: 8.6 - The three-phase wye-connected…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter8: Symmetrical Components

Section: Chapter Questions

Problem 8.13P

See similar textbooks

Similar questions

AC Power and Power Factor 1. Two loads are connected in parallel across a 13,200-volt line. Load A draws 200kW at 0.6 p.f. (lagging), load B takes 200kVA at 0.8 p.f. (lagging). Find the reactive, apparent and true power and the line current.
4) A balanced delta connected load of ...+j18 ohm per phase is connected at the end of a three phase line as shown in figure. The line impedance is 1+j2 ohm per phase. The line is supplied from a three-phase source with a lie- to-line voltage of 207.85 V rms. Taking Van as reference, determine the following: a) Current in phase a. b) Total complex power supplied from the source. c) Magnitude of the line-to-line voltage at the load terminal. (Please determine the impedance value within the specified limits: 16-26 V. By considering the impedance value you determined yourself, solve the question.) ao- |V₂| bo Co- 1 +j2 Ω = 207.85 V www Figure a Jum ...+j18 n b
Consider the circuit shown. Find the following: a. Total load impedance seen by the voltage source. b. Complex power delivered by the source. c. Average power delivered by the source. d. Reactive power delivered by the source. e. Load power factor and power factor angle.
Q. 2a) The impedance Zi and Z2 are connected in parallel across 200 V, 50 HZ single phase ac supply. Zi carries 2 A at 0.8 lag p.f. If the total current is 5 A at 0.985 lagging p.f. Determine - 1. Value of Z, and Z2 2. Total power and power consumed by Z2.
THESE ARE THE QUESTIONS FROM THE SUBJECT POWER SYSTEM FUNDAMENTALS AND THE CHAPTER IS PERFORMANCE OF TRANSMISSION LINES AND THE TOPIC IS SHORT TRANSMISSION LINES THE ANSWERS ARE GIVEN WITH THE QUESTION PLEASE DO ALL THE QUESTIONS PROPERLY „DONOT SKIP ANY STEP AND DO YOUR BEST 4.) Estimate the distance over which a load of 15000 kW at 0-85 p.f. can be delivered by a 3-phase transmission line having conductors of steel-cored aluminium each of resistance 0-905 O/phase per kilometre. The voltage at the receiving end is to be 132 kV and the loss in transmission is to be 7-5% of the load. [69-55 km] 5). A 3-phase line 3 km long delivers 3000 kw at a p.f. 0-8 lagging to a load. The resistance and reactance per km of each conductor are 0-40 and 0-3 Q respectively. If the voltage at the supply end is maintained at 11 kv, calculate: (i) ceceiving end voltage (line-to-line) (ii) line current (ii) transmission efficiency. [(i) 10.46 kv (ii) 207 A (ii) 95%] 6). A short 3-0 transmission line with an…
In a three-phase system voltage, assume that the phase-to-neutral voltage at phase “b” is considered as the reference (zero phase angle). 1. State the positive sequence and the negative sequence. 2. Solve the following for both sequences: a. the line-to-neutral voltages : VAN ,VBN and VCN b. the line-to-line voltages : VAB , VBC and VCA
What would be the phase-to-neutral voltage from a 3-phase, wye-connected system if the line-to-line voltage is 34,500Volts. a. 29,918.584V b. 19,918.584V C. 28.918.584V d. 18,918.584V
Q2) A 13.2-kV single-phase generator supplies power to a load through a transmission line. The load's impedance is Ztoad 500 236.87° ohm , and the transmission line's impedance is Zine = 60 253.1° ohm. To reduce transmission line losses to 0.0103 of its losses without using the transformers design and use two transformers T1 between the generator and the transmission line and T2 between the transmission line and the load.
2) Figure shows three loads connected in parallel across a 1000-V (rms), 60-Hz single-phase source. Load 1: Inductive load, ... kVA, 0.28 p.f. lagging Load 2: Capacitive load, ... kW, 40 kvar Load 3: Resistive load, 15 kW Determine the total (a) kW, (b) kvar, (c) kva, and (d) supply power factor. (Please determine the power values within the specified limits: Load 1 apparent power: 100-150 kVA, Load 2 active power: 5-20 kW. By considering the power values you determined yourself, solve the question.) Load Load DE 1 2 Load 3
Q2) A 13.2-kV single-phase generator supplies power to a load through a transmission line. The load's impedance is Zload = 500 236.87° ohm, and the transmission line's impedance is Zline = 60 253.1° ohm. To reduce transmission line losses to 0.0103 of its losses without using the transformers design and use two transformers T1 between the generator and the transmission line and T2 between the transmission line and the load.
A single phase line has an impedance of 0.4+j2.7 ohms. The line feeds two -single phase loads that are connected in parallel. The first load is absorbing 264.1 kVA at 0.707 power factor lagging. The second load absorbs 44kW at unity power factor. The voltage at the load end of the line is 2200 V. Assuming at the load end of the line as the reference axis. Determine the magnitude of the voltage at the source end of the line.
Two Alternators are operating in parallel supplying a common load of 4250KW at 85% power factor lagging. Alternator A contributes 600KVAR at 92% power factor lagging, determine the : a. KVA and power factor of the load b. KVA and power factor of alternator B.

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning