A 0.5-m-diameter pipe (ɛ = 0.9) carrying steam has a surface temperature of 500 K (see Fig. 1.25). The pipe is located in a room at 300 K, and the convection heat trans- fer coefficient between the pipe surface and the air in the room is 20 W/m2 K. Calculate the combined heat transfer coefficient and the rate of heat loss per meter of pipe length. %3D

A 0.5-m-diameter pipe (ɛ = 0.9) carrying steam has a surface temperature of 500 K (see Fig. 1.25). The pipe is located in a room at 300 K, and the convection heat trans- fer coefficient between the pipe surface and the air in the room is 20 W/m2 K. Calculate the combined heat transfer coefficient and the rate of heat loss per meter of pipe length. %3D

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.62P

See similar textbooks

Similar questions

Determine the rate of heat transfer per meter length to a light oil flowing through a 2.5-cm-ID, 60-cm-long copper tube at a velocity of 0.03 m/s. The oil enters the tube at 16C, and the tube is heated by steam condensing on its outer surface at atmospheric pressure with a heat transfer coefficient of 11.3 kW/m K. The properties of the oil at various temperatures are listed in the following table: Temperature, T(C) 15 30 40 65 100 (kg/m3) 912 912 896 880 864 c(kJ/kgK) 1.80 1.84 1.925 2.0 2.135 k(W/mK) 0.133 0.133 0.131 0.129 0.128 (kg/ms) 0.089 0.0414 0.023 0.00786 0.0033 Pr 1204 573 338 122 55
The heat transfer coefficient for a gas flowing over a thin float plate 3-m long and 0.3-m wide varies with distance from the leading edge according to hc(x)=10x1/4Wm2K If the plate temperature is 170C and the gas temperature is 30C, calculate (a) the average heat transfer coefficient, (b) the rate of heat transfer between the plate and the gas, and (c) the local heat flux 2 m from the leading edge. Problem 1.18
S is 6. A spherical shaped vessel of 1.4 m outer diameter is 90 mm thick. Find the rate of heat leakage, if the temperature difference between the inner and outer surfaces is 220°C. Thermal conductivity of the material of the sphere is 0.083 W/mK. (a) 0.2 kW (c) 1.088 kW (b) 0.5 kW (d) 1.6 kW
Heat transfer Calculate the heat transfer rate in Btu/hr through the pipe ona stainless steel pipe with a length of 12m has an inner diameterof 10in and an outer diameter of 13in. The temperature of theinner surface of the pipe is 50°C and the temperature of theouter surface is 48°C. The thermal conductivity of the stainlesssteel is 187 W/m-°C. Show complete solution in a clear paper.
3. Hot water flows inside a 2.5 cm inner diameter tube, the tube has a wall thickness of 0.8 mm (tube length=1m) with a conduction resistance of 0.000183 °C /W, the inner and outer convection resistance are (0.00662, 1.196 °C /W) respectively. The overall heat transfer coefficients depending on the outer diameter of the pipe is equal to: A. 9.94 W/m2 °C B. 200 W/m² °C C. 0.5 W/m² °C D. None of them
You are designing a 3m x 3m floor with radiant heating. The floor has 12 parallel pex pipes (k = 40 W/mK) of L = 3m, OD = 25mm and ID = 20mm. Hot water (TInfintiy 1 = 90oC, h = 200 W/m2K) runs through the pipes continuously. The surface below the pipes is perfectly insulated. Above the pipes, there is a 3mm layer of bonding material (? = 12 W/mK) and a 9mm layer of tile (k = 2 W/mK). Above the tile, there is air (TInfinity 2 = 25oC, h = 20 W/m2K). Properties of Air: k = 0.025 W/mK, Pr = 0.72, v = 1.847 x 10−5, u = 16.84 x 10−6, p = 1.2 kg/m3, B = 1/Tf (ideal gas), Hint: Assume that the “layer” of pipe starts at the center point (e.g. for conduction purposes, the pipe is OD divided by 2 thick). For convection, consider the entire pipe surface. a) What is the total heat rate entering the room above the floor? b) What is the temperature of the top of the tile?
Consider a pipe of 5 m in length and 1 cm in diameter. Temperature difference between the wall and the fluid (k = 1 W/mK) at exit is 25% that of at inlet. If the pipe wall temperature remains as constant of 80 ºC, total heat transfer rate 1000 W, and the flow is laminar what is the fluid temperature at inlet?
Water flows at 67 C inside a 2.5 cm inside diameter tube such that hi = 3500 W/m² .C . The tube has a wall thickness 0.72 mm with a thermal conductivity of 18 W/m.C. The outside of the tube loses heat by free convection with ho= 7.6 W/m².C. Calculate the overall heat transfer coefficient and heat loss per unit length to surrounding air at 15 C.
An electric motor is to be connected by a horizontal steel shaft (k 42.56 W/m.K), 25 mm in diameter to an impeller of a pump, circulating liquid metal at a temperature of 540°C. If the temperature of electric motor is limited to a maximum value of 52°C with the ambient air at 27°C and heat transfer coefficient of 40.7 W/m2.K, what length of shaft should be specified between the motor and pump? Steel shaft
Q1-A block as sphere made of Teflon initially at a temperature of 90 C is suddenly immersed in a fluid at 20 C. The convection heat- transfer coefficient is 15 W/m2 C. Determine the dimension of the block that it is just considered as lumped-capacity system. Calculate : (1) the time the center of the sphere reaches the half value of initial temperature and, (2) the heat loss from the block at that time.
A steam pipe line of 150/160 mm in diameter is covered with layer of heat insulating material of thickness 100 mm. Thermal conductivity of tube is 50 W/m deg C or kcal/m-hr-deg C and Ains,mat = 0.09 kcal/m- hr-deg C. Temperature of pipeline inside surface is 400 deg C and temperature of the outside surface of insulating surface is 50deg C. Find loss of heat from length of 1m of pipeline and temperature at interface of insulation.
A spherical shaped vessel of 1.4 m diameter is 90 mm thick. Find the rate of heat leakage, if the temperature difference between the inner and outer surfaces is 220oC. Thermal conductivity of the material of the sphere is 0.083 W/m-K.