A 0.78 m³ tank initially contains water at 260°C and a quality of 0.81. A valve at the top of the tank is opened and allows for saturated vapor at 260°C to leave the tank. The tank is maintained isothermally during this process until the tank is filled with only saturated vapor at 260° C. What is the mass of steam that leaves the tank during this process? How much heated is added to the tank during this process. KJ kg

A 0.78 m³ tank initially contains water at 260°C and a quality of 0.81. A valve at the top of the tank is opened and allows for saturated vapor at 260°C to leave the tank. The tank is maintained isothermally during this process until the tank is filled with only saturated vapor at 260° C. What is the mass of steam that leaves the tank during this process? How much heated is added to the tank during this process. KJ kg

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

As shown in the figure below, you have a system including a Polyethylene vessel with mass Myessel = 0.229 kg. The vessel contains water with mass Mwater = 0.399 kg. Both the vessel and water are initially at a temperature of 54.6 degrees Celsius. You add steam into the system. The steam has an initial temperature of 167.4 degrees Celsius and a mass of Msteam = 10.9564 kg. The system will reach equilibrium with all the water having vaporized at some final temperature above 100 degrees Celsius. Steam water Pressure Vessel Find the system final temperature, Tfinal = Material c (J/(kg K)) Aluminum 897 1820 Beryllium Cadmium Iron Lead 129 Polyethylene 2303 Steel 466 Uranium 116 231 412 All of the water turns to steam. The system reaches equilibrium at T > 100° C Water c (J/(kg K)) ice 2090 4186 2010 water steam degrees Celsius Water L (J/kg) 334000 Fusion Vaporization 2230000
Question 1 A piston-cylinder assembly with a frictionless piston has a volume of 0.1 m' and initially filled with steam of 0.5 kg at a pressure of 0.4 MPa. There is heat transfer until the temperature reaches 573 K. Find the total heat transfer as well as the work done during the process. Sketch the process on a P-v diagram with respect to the vapour dome.
ANSWER ALL THREE AND GET A LIKE <3 The density of helium is 0.178 kg/m3 at STP. What is the density in kg/m3 at 25°C and 98 kPa? A steel tank initially contains oxygen gas at 450 kPag and 20°C. After 2.5 kg of oxygen had been used, the pressure and temperature of the gas in the tank was found to be 180 kPag and 20°C, respectively. What was the initial mass of oxygen in the tank in kg? A 1500-L tank contains nitrogen at a pressure of 400 kPag and a temperature of 320K. Later, because of a leak, it was found that the gage pressure has dropped to 320 kPag and the temperature has decreased to 300K, determine the amount of nitrogen that has leaked out in kg.
The tank contains 2kg of water at 20C, 1 atm. The tank is heated. When the tank pressure reaches 300kpa, the valve opens and steam starts escaping. Heating continues and steam continues to escape while the pressure remains constant until half of the mass escapes. At this time the tank is filled with saturated vapor at 300 kpa, and the valve closes. Question: Determine the volume of the tank and the amount of supplied heat.
.A kilogram of Argon gas( MW= 40 kg/kmol, k=5/3) is in a piston cylinder set-up. Initially, it has pressure of 30kPa and volume of 0.2m3 and expanded to 20 kPa due to heat transfer. If the process is said to be isovolumic, find initial and final temperatures.
Initially, a rigid tank contains 500L of water at 300°C. By volume, the tank contains60% liquid and 40% vapor. At the bottom of the tank, as shown, a valve is opened and half of the mass of water is withdrawn which is in the liquid phase. Heat transfer takes place such that the temperature within the tank is constant. Determine the heat transfer in kJ required to withdraw half of its mass and maintain its temperature. (Provide Schematic Diagram if applicable)
Let's consider a closed container. This has a glass sight that allows you to observe the liquid level. The container contains refrigerant 134a at 20 ° C. A dough extraction is carried out from the bottom at a very low rate, the temperature remains constant throughout the process. If the area of the container is 0.05m ^ 2 and after liquid extraction the level drops150 mm, determine the mass of refrigerant that came out. see img
3-39 Water initially at 200 kPa and 300°C is contained in a piston-cylinder device fitted with stops. The water is allowed to cool at constant pressure until it exists as a saturated vapor and the piston rests on the stops. Then the water continues to cool until the pressure is 100 kPa. On the T-v diagram, sketch, with respect to the saturation lines, the process curves pass- 1stams! od on TURNACE ing through the initial, intermediate, and final states of the 1992 palam 11. water. Label the T, P, and U values for end states on the process artita ne odrow OFTİ 21 nucfortyd beinvarian curves. Find the overall change in internal energy between the 1610 PRICE initial and final states per unit mass of water. al state Onimals uliod Anub 1516w 3-150 3-160 In Water 200 kPa 300°C 3-17C ment rises. Now on top of air Obs will rise in a co FIGURE P3-39 180 Q
A rigid tank contains 2.0 kg of nitrogen at 100 K and ? = 0.50. Then, 0.5 kg ofnitrogen is removed from the tank through a valve. If the temperature remains constant throughout the process, determine the final state of the nitrogen inside the tank and the volume of nitrogen removed if the valve is located at(a) The top(b) The bottom
A rigid tank initially contains 1kg of saturated water vapor (x-1) at T= 120-C. Now, the tank is started to be cooled until the temperature of the water drops to 80-C. During the process the volume of the tank is kept fixed. a) Calculate the mass of the liquid water left inside the tank after the cooling. b) Calculate the amount of heat extracted from the water inside the tank during this proces
An ideal gas at 27 oC is heated at constant pressure till the volume becomes three times. The temperature of the gas will then be
1) A piston-cylinder assembly contains 10 kg of refrigerant 134a. Initially, 8 kg of SA134a is in the liquid phase and the temperature is -10°C. Then there is a slow heat transfer to SA-134a, the piston rises and the piston touches the stoppers when the volume is 400 liters. (a) Show the phase change in the P-V diagram, (b) the temperature of the system at the moment the piston contacts the stoppers, (c) calculate the work done during the process.