A 2-wire d.c. distributor AB 500 meters long is fed from point Aand is loaded as under:Distance from feeding point A (in metres) 100 300 400 500Load (amperes)40 402050If the specific resistance of copper is 1∙7 × 10¯8 №m, what must be thecross-section of each wire in order that the voltage drop in thedistributor shall not exceed 10 volts ?

Given: In this question, the given details are, A 2-wire d.c distributor AB 500 meters long is fed…

A 2-wire d.c. distributor AB 500 meters long is fed from point A and is loaded as under: Distance from feeding point A (in metres) 100 Load (amperes) 20 If the specific resistance of copper is 1.7 × 10-8 cross-section of each wire in order that the distributor shall not exceed 10 volts ? 300 400 500 40 40 50 m, what must be the voltage drop in the

A 2-wire d.c. distributor AB 500 meters long is fed from point A and is loaded as under: Distance from feeding point A (in metres) 100 Load (amperes) 20 If the specific resistance of copper is 1.7 × 10-8 cross-section of each wire in order that the distributor shall not exceed 10 volts ? 300 400 500 40 40 50 m, what must be the voltage drop in the

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.7MCQ: Consider Figure 3.5. Match the following, those on the left to those on the right. (i) Im (a)...

See similar textbooks

Similar questions

Q2/A- what are the main cases of insulator failures? B-what are type testing of insulator?
this is both copper., Can you explain the changes when I changed the WIRE GAUGE SIZE FROM THICK TO THIN? ELABORATE
These Insulators are used when equal Voltage is required across each Insulator unit. O A. RADING INSULATORS O B. GRADING INSULATORS O C. STRAINING INSULATORS O D. GAINING INSULATORS
A 14/2 type NM copper used for a general lighting branch circuit Ampacity : Maximum fuse or circuit breaker size:
For 7442 IC, HIGH voltage (near + 5 V) stood for ( 0 , 1)?
1. What happened if the DC voltage in the clamping circuit is replaced by an a.c source?
1, determine the Rab (integer), Rbc (4 decimal places, Rca (4 decimal place) and Rcc (integer) as show in figure 2. 2. Determine voltage across "a" and "b" as show in the figure 5. round of 4 decimal places
A string insulator has 6 units. The voltage across the bottom most until is 20% of the total voltage. Its string efficiency is?
An AC ammeter is connected in series with the primary winding of T1. What is the expected current reading? An AC ammeter is connected in series with the secondary winding of T1. What is the expected current reading? An AC ammeter is connected in series with R1. What is the expected current reading? NOTE: Idc for HW rectifier = 0.318 * Ipeak = 0.45 * Irms Describe/Explain briefly the purpose/use of the array (series-parallel) connection of the rectifier diodes in the given circuit.
For the network shown in Figure B22 , assume E = 17V,Diode Di, D2 as Germanium Ri-2KΩ and R2-3ΚΩ. Calculate, i. Current I1, i. Current ID2 ii. Voltage across resistor R2 R1 D1 + E D2 I2 R2 Figure B22
3. A 2-wire d.c. distributor A B 500 metres long is fed from point A and is loaded as under : Distance from feeding point A (in metres) Load (amperes) If the specific resistance of copper is 1-7× 10*2m, what must be the cross-section of each wire in order that the voltage drop in the distributor shall not exceed 10 volts ? 100 300 400 500 20 40 40 50 (1-734 cm³]
For the network shown in Figure B22 , assume E = 17V,Diode Di, D2 as Germanium R1=2KQ and R2=3K2. Calculate, i. Current I1, ii. Current ID2 ii. Voltage across resistor R2 R1 Di + E D2 I2 R, Figure B22