A 5 KVA, 11000/220-V, 60 Hz, single-phase conventional transformer is supplying 2.8 KW of power to a load at 0.8 Lagging power factor, a load voltage of 220 Volts. Its Equivalent circuit is given below. Calculate the magnitude of the input voltage of this transformer. +0 a Ih+es 2440 S2 Select one: O a. Vp = 13.62 KV O b. None O c. Vp 12940.4 Volts O d. Vp 14.03 KV 0.808+j 4.04 52 Ims j700.352 Is Vs 0+

A 5 KVA, 11000/220-V, 60 Hz, single-phase conventional transformer is supplying 2.8 KW of power to a load at 0.8 Lagging power factor, a load voltage of 220 Volts. Its Equivalent circuit is given below. Calculate the magnitude of the input voltage of this transformer. +0 a Ih+es 2440 S2 Select one: O a. Vp = 13.62 KV O b. None O c. Vp 12940.4 Volts O d. Vp 14.03 KV 0.808+j 4.04 52 Ims j700.352 Is Vs 0+

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.28MCQ

See similar textbooks

Similar questions

A 23/230-kV step-up transformer feeds a three-phase transmission line, which in turn supplies a 150-MVA,0.8 lagging power factor load through a step-down 230/23-kV transformer. The impedance of the line and transformers at 230kVis18+j60. Determine the tap setting for each transformer to maintain the voltage at the load at 23 kV.
A 250/125 V, five kVA single-phase transformer has a primary resistance of 0.2 ohms and reactance of 0.75 ohms. The secondary resistance is 0.05 ohm and reactance of 0.2 ohms.a) Determine its regulation while supplying full load on 0.8 leading p.f.b) The secondary terminal voltage on full load and 0.8 leading p.f.Ans.: -0.4.88%; 131.1
Design a CT-FWR to supply a load of (502) with a waveform of the following specifications: - • Vdc = 12 V • Ripple factor = 0.1 % • the main power supply is (220 Vrms, 50 Hz). Determine the following values: - 1- The value of capacitor filter. 2- The maximum load voltage (VmR) 3- The transformer turns ratio (a). 4- The RMS value of the load voltage. 5- Draw the output waveform. (assume ideal diodes)
With base MVA of 150 and base voltage of 33. If the reactance of the transformer is 0.23 pu. The parameter of the reactance of the transformer in the Neplan software is O 1.66 2.30 23 0.23 O Non of them
Determine the peak-to-peak ripple and dc output voltages. The transformer has a 36 V rms secondary voltage rating, and the line voltage has a frequency of 60 Hz. Neglect Rsurge.
A transformer has a reactive drop of 6% and a resistive drop of 2.5%. Determine the lagging power factor at which the voltage regulation is maximum and the value of this regulation.[0.385 lag]
5. ReqLs = 0.00820, Xeq Ls = 0.0223N Step down transformer delivers 135 kW to a load at 0.9 lagging power factor at rated voltage. Determine the Following: a) Terminal voltage (LV side). b) Terminal voltage (HV side). c) High side current. d) Input impedance. e) Voltage regulation. f) Efficiency. g) Voltage regulation for 0.9 leading pf. h) Draw the phasor diagram of secondary circuit at 0.9 lagging pf. i) Draw the phasor diagram of secondary circuit at 0.9 leading pf. 150 kVA, 2800-240 V, 50 Hz transformer. RiH-2200Ω Χ.Η1 200Ω
A power transformer with standard insulation class of 69 kv will withstand an rms test voltage of A. 140 kv. B. 350 kv. C. 69kv. D. 440 kv.
7. The primary of a single-phase transformer takes 1 A at power factor of 0.4 when connected to a 240-V, 50-Hz supply and the secondary is on open circuit. The number of turns on the primary is twice that on the secondary. A load taking 50 A at a lagging power factor of 0.8 is now connected across the secondary. What is now the value of the primary current ? transformer.) (Neglect the voltage drops in the
What is the relationship between primary induced emf( E1) and applied voltage (V1) of a Transformer? O a. Both are unequal and in phase O b. Both are unequal and 180 degree out of phase O c. Both are equal and 180 degree out of phase O d. Both are equal and inphase
6. A single-phase, 225-kVA, 460/120-V transformer has 6% impedance and 96% efficiency. Find its series Rand X in percent and in ohms looking from the HV side source. 7. Determine the rms fanlt currents on both sides of a 100-IVA single nhase
Single phase half wave AC-AC converter has a resistance of R = 50 ohms. Input voltage is given as 230 Vrms. Transformer conversion ratio is 1:1. If T1 thyristor is triggered at 60 degrees; a)Rms output voltage? b)Output power? c)RMS load current and average load current? d)Input power factor? e)Average and RMS thyristor current?