A brass bar is fastened between a steel bar and an aluminum bar as shown in the figure. Axial loads are applied at the positions indicated. Find the largest value of P (kN) that will not exceed the maximum stresses are: 140 MPa in the steel, 120 MPa in the brass and 80 MPa in the aluminum. [Roundoff your final answer to 2 decimal places] Brass A = 650 mm? Steel Aluminum A = 320 mm? A = 480 mm? 3P 4P 2P 1.0 m 2.0 m 1.5 m

A brass bar is fastened between a steel bar and an aluminum bar as shown in the figure. Axial loads are applied at the positions indicated. Find the largest value of P (kN) that will not exceed the maximum stresses are: 140 MPa in the steel, 120 MPa in the brass and 80 MPa in the aluminum. [Roundoff your final answer to 2 decimal places] Brass A = 650 mm? Steel Aluminum A = 320 mm? A = 480 mm? 3P 4P 2P 1.0 m 2.0 m 1.5 m

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
As shown in the figure below, a bronze bar is affixed between a steel bar and an aluminum bar. Axial loads are applied at the positions indicated. If the largest value of P that will not exceed an overall deformation of 4.0 mm, or the following stresses: 150 MPa in the steel, 130 MPa in the bronze, and 90 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. determine the stress in the bronze, steel, and aluminum
The light rigid bar ABCD shown is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P = 20 KN is applied. %3D Steel E200 GPa A-600mm L1 m 2.0 m 0.6 m 1.5 m Pa20 KN Aluminum E-70 GPa A=900mm L-1.5 m What is the ratio of the deformation of steel to deformation of aluminum?
A bronze bar is fastened between a steel bar and an aluminum bar as shown in the figure. Axial loads are applied at the positions indicated. The allowable overall deformation is not to exceed 1.2 mm. Assume that the 2P Aluminum L- 1.5 m A= 550 mm E= 70 GPa Steel Bronze L= 2.0 m L= 1.0 m A= 600 mm A= 650 mm E= 200 GPa E= 83 GPa assembly is suitably braced to prevent buckling. Find the maximum permissible value of P.
A compressive load P is transmitted througha rigid plate to three magnesium-alloy bars that areidentical except that initially the middle bar is slightlyshorter than the other bars (see figure). The dimensionsand properties of the assembly are as follows:length L = 1.0 m, cross-sectional area of each barA = 3000mm2, modulus of elasticity E = 45 GPa,and the gap s = 1.0 mm.(a) Calculate the load P1 required to close the gap.(b) Calculate the downward displacement d of therigid plate when P = 400 kN.(c) Calculate the total strain energy U of the threebars when P = 400 kN.(d) Explain why the strain energy U is not equal toPδ / 2. Hint: Draw a load-displacement diagram.
5. A bronze bar is fastened between a steel bar and an aluminum bar as shown in Figure 5. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. Steel A = 480 mm² 1.0 m Bronze A = 650 mm² 3P 4P 2.0 m FIGURE 5 Aluminum A = 320 mm² 1.5 m 2P
Situation No. 2 A bronze bar is fastened between a steel bar and an aluminum bar as shown below. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. Bronze Steel A = 480 mm? Aluminum A = 650 mm A = 320 mm 3P 4P 2P 1.0 m 2.0 m 1.5 m
As shown in the figure below, a bronze bar is affixed between a steel bar and an aluminum bar. Axial loads are applied at the positions indicated. If the largest value of P that will not exceed an overall deformation of 4.0 mm, or the following stresses: 150 MPa in the steel, 130 MPa in the bronze, and 90 MPa in the aluminum, determine the stress in the bronze. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. (The correct answer is 71.36 MPa. Can you show the solution? Thank you!)
Problem 2: A bronze bar is fastened between a steel bar and an aluminum bar as shown. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. Steel Bronze 480 mm² 650 mm² 3P 1.0 m 4P 2.0 m Aluminum 320 mm² 1.5 m 2P
An aluminum tube is fastened between a steel rod and a bronze rod as shown. Axial loads are applied at the positions indicated. For Bronze: Allowable stress = 120 MPa, EB = 83,000 MPa For Aluminum: Allowable stress = 120 Mpa, EA = 70,000 MPa For Steel: Allowable stress = 120 MPa, Es = 200,000 MPa Assume that the assembly is suitably braced to prevent buckling. Maximum overall deformation should not exceed 2mm. a) Give the value of the force acting on the bronze so as not to exceed allowable stresses and deformation. b) Give the value of the force acting on the aluminum so as not to exceed its allowable stresses and deformation. c) Give the value of the force acting on the steel so as not to exceed its allowable stresses and deformation.
8. If the modular ratio is equal to 11, and the Modulus of Elasticity of the Steel is 200,000 MPa. What is the value of fc'?
An aluminum rod is rigidly attached between a steel rod and a bronze as shown. Axial loads are applied at the positions indicated. Find the stress of each rod in MPa. Steel Aluminum Bronze A- 500mm? A = 400mm? A - 200mm 40KN 10KN 20KN 2.5m 2.0m 1.5m