H.W.1: A steel bar 6 m long is 5 cm in diameter for 3m of its length and 2.5 cm indiameter for the second 3m as shown in Figure below. The smallest diameter part of thebar is with 11 N/mm2 tensile stress due to the applied load. Find the final diameters ofthe two parts after the applied load. E for the steel is 200x10 N/mm and u of the steel is0.28.P3 m3 m

Answered: Image /qna-images/answer/659e5a1c-fb56-43b8-b25a-de4d9b5fbbac.jpg

H.W.1: A steel bar 6 m long is 5 cm in diameter for 3m of its length and 2.5 cm in diameter for the second 3m as shown in Figure below. The smallest diameter part of the bar is with 11 N/mm? tensile stress due to the applied load. Find the final diameters of the two parts after the applied load. E for the steel is 200x10 N/mm² and u of the steel is 0.28. P 3 m 3 m

H.W.1: A steel bar 6 m long is 5 cm in diameter for 3m of its length and 2.5 cm in diameter for the second 3m as shown in Figure below. The smallest diameter part of the bar is with 11 N/mm? tensile stress due to the applied load. Find the final diameters of the two parts after the applied load. E for the steel is 200x10 N/mm² and u of the steel is 0.28. P 3 m 3 m

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

One of the following values is a possible for possion ratio for steel ? a. Zero b. one c. 0.3 d 0.9
A compressive load P is transmitted througha rigid plate to three magnesium-alloy bars that areidentical except that initially the middle bar is slightlyshorter than the other bars (see figure). The dimensionsand properties of the assembly are as follows:length L = 1.0 m, cross-sectional area of each barA = 3000mm2, modulus of elasticity E = 45 GPa,and the gap s = 1.0 mm.(a) Calculate the load P1 required to close the gap.(b) Calculate the downward displacement d of therigid plate when P = 400 kN.(c) Calculate the total strain energy U of the threebars when P = 400 kN.(d) Explain why the strain energy U is not equal toPδ / 2. Hint: Draw a load-displacement diagram.
Determine the following: Displacement of B (in mm) with respect to A. Displacement of C (in mm) with respect to A. Principal stresses at point O, if it is 200mm from C. (unit should be kPa). A-36 steel with the following properties: Modulus of Elasticity, E = 29x10^3 ksi or 200 GPa Shear Modulus/Modulus of Rigidity, G = 11.5x10^3 ksi or 79.3 GPa Poisson's Ratio, nu = 0.260 Temperature Coefficient for thermal expansion, a = 6.6x10^-6/°F or 11.7x10^-6/°C
2.3-7 A steel bar 2.4 m long has a circular cross section of diameter d, = 20 mm over one-half of its length and diam- eter d, = 12 mm over the other half (see figure part a). The modulus of elasticity is E = 205 GPa. (a) How much will the bar elongate under a tensile %3D %3D load P = 22 kN?
The modulus of elasticity of mild steel is equal to .. .? .... .. a. 2 x 10ʻN/m? a. 2 x 10'N/m 2 b. 2 x 10° N/m 4 c. 2 x 10 N/mm 5 d. 2 x 10 N/mm Check
What is the value of reduction factor of the beam, if the stress in the steel is 400 MPa, and the Modulus of Elasticity of the Steel is 200,000 MPa. O 0.671 0.692 O 0.660 O 0.650 None of the Choices O 0.681
1. A circular rod of diameter 20 mm and 500 mm long is subjected to a tensile force 45 kN. The modulus of elasticity for steel may be taken as 200 Kn/mm². Fine stress, strain and elongation of the bar due to applied load.
SITUATION. A steel plate ABCD of thickness t = 5mm is subjected to uniform stresses: = 100 MPa 0₂ = -60 MPa. Ox E =200GPa, v= 1/3 a = 160mm and b = 200 mm Calculate the change in thickness (mm). -0.0023 mm 0.0023 mm O O 0.0045 mm - 0.0045 mm Ł B AL C D X
A brass bar is fastened between a steel bar and an aluminum bar as shown in the figure. Axial loads are applied at the positions indicated. Find the largest value of P (kN) that will not exceed the maximum stresses are: 140 MPa in the steel, 120 MPa in the brass and 80 MPa in the aluminum. [Round off your final answer to 2 decimal places] Steel Brass A = 480 mm A = 650 mm? Aluminum A = 320 mm? 3P 4P 2P 1.0 m 2.0 m 1.5 m
A 5.0m simple beam supports the given floor loads Wu and a concentrated load Pu due to the wall transverse to the given beam. Answer the following questions given the sections of the beam. 2.0 m | P₁ = 45 KN W₁ = 44.24 kN/m 3.0 m a. b. 3-200 6-200 350mm by 400mm f'c-35 MPa fy=415 MP.. Ps= 10 mm conc. cover= 40mm 250mm by 400mm f'c-21 MPa fy=415 MPa Ps= 10 mm conc. cover= 40mm
5. A bronze bar is fastened between a steel bar and an aluminum bar as shown in Figure 5. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. Steel A = 480 mm² 1.0 m Bronze A = 650 mm² 3P 4P 2.0 m FIGURE 5 Aluminum A = 320 mm² 1.5 m 2P
Problem 1 A bar obtained by bonding together pieces of aluminum (Ea section shown below. Considering that the allowable stress (both in compression and tension) of aluminum and brass are 120 MPa and 180 MPa, respectively, determine the largest moment M that can be applied about the 70 GPa) and brass (Eb 105 GPa) has the cross horizontal axis. 8 mm 8 mm 32 mm- 8 mm 32 mm 8 mm Brass Aluminum