A composite bar is rigidly attached to the wall at A as shown in the figure. Axial loads are applied at the positionsindicated.3 m2.5 mC1200 kN900 kN80mmØ100mmØE = 83 GPaBronzeE = 200 GPaSteelWhich of the following most nearly gives the deformation of C?a. -0.7855 mmО Ъ. +0.8575 mmc. +0.7855 mmo d. - о.8575 mm

Answered: Image /qna-images/answer/abbb57f3-9276-4a37-a742-0a6315f5d1d0.jpg

A composite bar is rigidly attached to the wall at A as shown in the figure. Axial loads are applied at the positions indicated. 3 m 2.5 m C 1200 kN + 900 kN 100mmø E = 83 GPa Bronze 80mmø E = 200 GPa Steel Which of the following most nearly gives the deformation of C? O a. -0.7855 mm о Ъ. +0.8575 mm O c. +0.7855 mm O d. 0.8575 mm

A composite bar is rigidly attached to the wall at A as shown in the figure. Axial loads are applied at the positions indicated. 3 m 2.5 m C 1200 kN + 900 kN 100mmø E = 83 GPa Bronze 80mmø E = 200 GPa Steel Which of the following most nearly gives the deformation of C? O a. -0.7855 mm о Ъ. +0.8575 mm O c. +0.7855 mm O d. 0.8575 mm

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN. 0.8m 0.4m B 5KN 0.6m Al 20KN Q2 5) What is the deformation 8, in mm? A=800 mm? A=1,200 mm?
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 6) What is the deformation &c in mm? 0.8m 0.4m B 5KN 0.6m 20KN A=800 mm? A=1,200 mm²
Calculate the axial deformation of the Brass cylinder section (BC) shown in Figure 8. The cross-sectional areas are Asteel = 80 x 10-³ m² and ABrass = 50 x 10-³ m², and Young's modulus - of steel and brass are 200 MPa and 120 MPa. 100 kN (a) 3.13 mm (b) 7.25 mm (c) 7.5 mm (d) 3.5 mm Steel 50 kN 0.5 m B Brass 0.3 m C Figure 8. A shaft of different diameters Steel 0.5 m Ꭰ 150 kN
An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m 10KN 0.8m 0.4m 5KN 0.6m What is the deformation 8Rc in mm? Al 20KN A=800 mm? A=1,200 mm²
The cross-sectional area of an aluminum bar is 170 mm?. It carries an axial loads at the positions as shown in the figure. Compute the total deformation of the bar if E = 80 Gpa. Assume the bar is suitably braced to prevent buckling. Add "9" in the loads only. Example: 40+9=49, 18+9=27, 42+9=51, 20+9=29 Area = 170mm' 2 40KN 18KN 20KN 42KN 1.0m 1.80m 0.70m
The composite shaft, consisting of aluminum, copper, and steel sections, is subjected to the loading shown. Determine the displacement of end A with respect to end D and the normal stress in each section. The cross-sectional area and modulus of elasticity for each section are shown in the figure. Neglect the size of the collars at B and C. Steel Eg = 200 GPa Acp= 39 mm? Aluminum Соpper Eg = 70 GPa AAB= 58 mm? Ecu = 126 GPa ABc = 77 mm? 16 kN 8 kN 9 kN 7 kN 16 kN 8 kN – 450 mm- -300 mm- 400 mm-
Q/ Find the Maximum stresses in Steel and Aluminum. Est= 210G pa and E al%3D 70 G pa ? W= 15 Kn.M 120mm 5m Al steel 60mm 140 mm
PROBLEM 6/6 F = 520 kN Determine the stress in each aluminum and steel bars after 0.2 mm F = 520 kN is applied. Note that a gap of 0.2 mm exist before the external load is Steel 280 mm applied and bars has equal distance with each other. Neglect the weight at the flat form. A = 1100 mm? E = 200 Gpa Steel Aluminum A = 2500 mm2 %3D E = 70 GPa %3D
Determine the following: Displacement of B (in mm) with respect to A. Displacement of C (in mm) with respect to A. Principal stresses at point O, if it is 200mm from C. (unit should be kPa). A-36 steel with the following properties: Modulus of Elasticity, E = 29x10^3 ksi or 200 GPa Shear Modulus/Modulus of Rigidity, G = 11.5x10^3 ksi or 79.3 GPa Poisson's Ratio, nu = 0.260 Temperature Coefficient for thermal expansion, a = 6.6x10^-6/°F or 11.7x10^-6/°C
The shown plate is 60 mm thick and it is made of Magnesium Am1004-T61. The plate is fitted between the rigid frictionless supports as shown and at T, = 20°C it is stress free. Find the stresses in the x and y directions when the temperature increases to T, = 58°C. %3D 150 mm 150 mm Select one: O x: 0 MPa, y: 42.864 MPa Ox: 22.1 MPa, y: 44.2 MPa Ox: 0 MPa, y: 44.2 MPa Ox: 0 MPa, y: 17.8 MPa O x: 13.2 MPa, y: 44.2 MPa Ox: 0 MPa, y: 67.4 MPa 3:10 PM O G 4) ENG 1/31/2021
! Required information A steel bar (Es= 210 GPa) and an aluminum bar (Ea = 70 GPa) are bonded together to form the composite bar shown. 8 mm 8 mm 8 mm Aluminum 24 mm -Steel Determine the maximum stress in steel when the bar is bent about a horizontal axis, with M= 56 N.m. The maximum stress in steel is - MPa.