A cylinder of mass 100 kg is in contact with the smooth surfaces at And B and in static equilibrium when a 300 N force is applied as shown. (a) Determine the reactions at the contact points A and B. (b) Determine the reactions for the pin at C (point) (c) What should be the applied force such that the cylinder loses contact with point A and is about to roll over point B? (Note: the reaction at B will change too) (2 points) 250 mm B 4 1100 mm 300 N

A cylinder of mass 100 kg is in contact with the smooth surfaces at And B and in static equilibrium when a 300 N force is applied as shown. (a) Determine the reactions at the contact points A and B. (b) Determine the reactions for the pin at C (point) (c) What should be the applied force such that the cylinder loses contact with point A and is about to roll over point B? (Note: the reaction at B will change too) (2 points) 250 mm B 4 1100 mm 300 N

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter5: Three-dimensional Equilibrium

Section: Chapter Questions

Problem 5.42P: The 350-lb homogeneous plate has the shape of an isosceles triangle. The plate is supported by a...

See similar textbooks

Similar questions

The homogeneous 240-lb bar is supported by a rough horizontal surface at A, a smooth vertical surface at B, and the cable BC. Draw the FBD of the bar and count the unknowns.
The 40-kghomogeneous disk is placed on a frictionless inclined surface and held in equilibrium by the horizontal force P and a couple C (C is not shown on the figure). Find P and C.
The uniform bar AB of weight W and length L is pinned to a sliding collar at A and to the sliding rod BD at B. The spring wound around rod BD has a stiffness k and is undeformed when rod AB is in the position =0. Determine the expression for the angle (other than =90 ) at equilibrium and investigate the stability of equilibrium for this position.
The uniform bar of weight W is held in equilibrium by the couple C0. Find C0 in terms of W, L, and .
The spring attached to the homogenous bar of weight W is undeformed when =0. Determine the smallest spring stiffness k for which the =0 equilibrium position will be stable. Use W = 10 lb, a = 24 in., and b = 6 in. Assume that the spring remains horizontal, which is a valid approximation if is small.
The 350-lb homogeneous plate has the shape of an isosceles triangle. The plate is supported by a thrust hinge at A, a slider hinge at B, and the cable CD. Find the force in the cable and the magnitudes of the hinge reactions.
The bar ABC is supported by three identical, ideal springs. Note that the springs are always vertical because the collars to which they are attached are free to slide on the horizontal rail. Find the angle at equilibrium if W = kL. Neglect the weight of the bar.
PROBLEM #1: A vertical force P = 20 lb is applied to the ends of the 2-ft cord AB and spring AC. If the spring has an unstretched length of 2 ft. Take k = 25 lb/ft. (see picture for illustration). Determine the: (a) forces (b) angle theta for equilibrium Note: Kindly show the complete step-by-step solution. Please make sure that your handwriting is understandable and the picture of the solution is clear. I will rate you with “like/upvote” after. I need the answer right away, thank you. Topics Discussed: Static of Rigid Bodies, Equilibrium of a Particle, Position Vector, Force Vector Direction, etc.
2.5 m 3.0 m 4000 N m 2.5 m 300 N 2 m 30° A smooth and weightless rod is subject to a force on one end and a moment at its mass center. If the Uniform rod is supported at multiple points as shown in the picture, find the reaction forces at these supports. Assume that the rod is supported at point A by a smooth wall and at B and C either at the top OR bottom by rollers. On your answer sheet provide the FBD and all your calculations.
End B of the uniform 2.7-kg bar AB is connected to a small roller that moves in a horizontal slot. The other end of the bar is pinned to the homogeneous 1.8-kg disk that rolls without slipping on the vertical surface. The spring attached to A has a free length of 0.3 m and a stiffness of 58 N/m. After the system is becomes horizontal. Determine the magnitude of the force P that acts on the bar at B. 2.1 m 0.24 m 0.9 m www 1.8 kg 1.5 m 2.7 kg P
The bent rod in Fig. a is supported at A by a journal bearing, at D by a ball-and-socket joint, and at B by means of cable BC. Using only one equilibrium equation, obtain a direct solution for the tension in cable BC. The bearing at A is capable of exerting force components only in the z and y directions since it is properly aligned on the shaft. In other words, no couple moments are required at this support. 1m B 0.5 m .Free-Body Diagram. As shown in Fig. b, there are six unknowns 0.5 m Equations of Equilibrium. The cable tension Tg may be obtained directly by summing moments about an axis that passes through points D and A. Why? 100 kg (a) Since the moment arms from the axis toTg and W are easy to obtain, we can determine this result using a scalar analysis. As shown, Fig. b EMDA = 0; TR(1 m sin 45°) – 981 N(0.5 m sin 45°) = 0 ATB T = 490.5 N B IB 45°- 0.5 m W = 981 N TE Dy 0.5 m Ip. (b)
The bent rod in Fig. a is supported at A by a journal bearing, at D by a ball-and-socket joint, and at B by means of cable BC. Using only one equilibrium equation, obtain a direct solution for the tension in cable BC. The bearing at A is capable of exerting force components only in the z and y directions since it is properly aligned on the shaft. In other words, no couple moments are required at this support. 1m B 0.5 m E .Free-Body Diagram. As shown in Fig. b, there are six unknowns 0.5 m Equations of Equilibrium. The cable tension Tg may be obtained directly by summing moments about an axis that passes through points D and A. Why? 100 kg