A full wave rectifier using a diode bridge and a 120V/12V transformer is designed to deliver power to a 100 load. Assume all diodes have Von=0.7V and negligible off current. a. What is the ripple voltage, if the capacitance of the filter is 2500μF? b. Considering the ripple calculated in part a, what is the average DC voltage of the output (hint: it will be approximately the peak (max) voltage minus Vr/2)? c. Considering the average DC voltage of the output found in part b, determine the average current and power in the load resistor.

A full wave rectifier using a diode bridge and a 120V/12V transformer is designed to deliver power to a 100 load. Assume all diodes have Von=0.7V and negligible off current. a. What is the ripple voltage, if the capacitance of the filter is 2500μF? b. Considering the ripple calculated in part a, what is the average DC voltage of the output (hint: it will be approximately the peak (max) voltage minus Vr/2)? c. Considering the average DC voltage of the output found in part b, determine the average current and power in the load resistor.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Suppose we have a 10-V-peak sinusoidal voltage source. Draw the diagram of a circuit that clips off the part of the sinusoid above 5 V and below -4 V. The circuit should be composed of ideal diodes, dc voltage sources, and other components as needed. Be sure to label the terminals across which the clipped output waveform vo(t) appears.
Sketch and explain the output wave shape for the circuit. The generator signal is a sine wave with a 5V peak. Use the second approximation of the real diode.
Assume the diodes to be ideal ,descibe the transfer functionality for the following circuit.
Design a clipping circuit that will limit the output voltage to 5V when applying an input sinusoidal waveform with a peak value of 10V. Assume available diodes with voltage drop of 0.5V. Sketch the output waveform of the circuit.
Sketch and explain the output voltage for the circuit below. The generator signal is a sine wave with a 100V peak. Use the second approximation of the real diode.
In the circuit of the following figure, the input voltage Vs is 15 volts rms with a frequency of 60 Hz, R equals 150 Ohms and C equals 100,000 Pico Farads. The diodes are Germanium (Vd = 0.2 volts) and the Zener diode is 12 volts. a) The magnitude of the ripple voltage at Cb) The Magnitude of the Peak Inverse Voltage (PIV) for D1 and D2.
29. Does an increase in reverse bias for a Varactor diode cause an increase or decrease in capacitance? 30. If the load current through a SCR (Thyristor) reduces to almost zero, what will be the result?
Make the described voltage multiplier circuit, determine the voltage charge in each capacitor, and the output voltage of the circuit. Plot the output waveform in proper phase alignment with the input voltage. Indicate the peak values with the support of your solutions. Use silicon diodes in your analysis and an input V=10 Vrms. a) Half-wave voltage doubler b.) Full-wave voltage doubler
Discuss the biasing and saturation voltage of a diode. Suggest how one can unidirectional DC output. convert AC to the
Q1 A. Design a clamper to perform Silicon diodes 10 V 2.7 V the function indicated in Figure shown below. Design B. Clip the output waveform to -10 V -17.3 V (+0.7 V and -0.7 V).
Sketch i agains v to scale for the circuit. Assume 0.6 V for all diodes in the forward-bias region.
Problem # 4 In the circuit shown below. Determine the following a. Vs (at the secondary) b. Vout (across RL) c. Vrip (ripple votage) d. VpC e. PIV (Peak Inverse Voltage) 10:1 Dy 1ISV ms Ouiput RL 2.2 k2 D, 50 pF All diodes are IN4001. alleee