Answered: A hole of 40 mm diameter and 50 mm…

A hole of 40 mm diameter and 50 mm depth is to be drilled in a milled steel component. The cutting speed can be taken as 65 m/min and the feed rate as 0.25mm/rev. Calculate the machining time

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 22. Calculate the rpm for machining a cast iron work piece 10 inches in diameter and the cutting…

Q: In a surface broaching process, a broach having 5 mm pitch and cut per teeth 0.05 mm is used for…

Q: (b) During a certain machining experiment at the UCSI workshop, it is observed that temperature at…

A: (i). In a metal cutting process, Maximum heat is carried out by chip then tool and lastly by the…

Q: Calculate resultant force, metal removal rate and shear strain in an orthogonal cutting the depth of…

Q: Calculate the spindle speed for a Lathe Machine, if the cutting speed for a mild steel material…

A: Cutting speed for mild steel, Vc=34 m/min Diameter of workpiece, d=46 mm=0.046 m

Q: How is feed related to speed in machining operations such as Evaluate and Explain. turning ?

A: Feed rate is the speed at which the cutter is fed, that is, advanced against the piece of work. it's…

Q: Calculate the r/min required for finish turning

Q: In an orthogonal cutting operation an 8 mm deep groove is to be turned on a 50 mm diameter steel…

Q: Estimate the machining time that will be required to finish a vertical flat surface of length 100 mm…

A: Given Length = 100 mm Height = 20 mm Diameter = 32 mm Milling machine length = 60 mm Velocity = 30…

Q: A mild steel rod having 50 mm diameter and 500 mm length is to be turned on a lathe. Determine the…

Q: A 4"x 8" cast steel plate is to be machined using a milling cutter with 8 inserts. The operation is…

A: Given dataD=8inchV=350sfpm=350×39.37=inch/minf=0.015inch/totthl3=0.18inchz=8 ***as per our company…

Q: Calculate the time required to make a finish cut, at a feed rate of 0.010mm on a piece of machine…

A: Given:Feed rate,fn=0.10 mm/secL=250 mmd=30 mm

Q: Q3). A block of 190mm length and 100mm width is to be machined in shaping process. The permissible…

Q: A 200 mm long magnesium alloy bar, 63 mm in diameter is turned on a lathe using a high speed steel…

A: Given data, Length of the magnesium alloy bar, L = 200 mm Diameter of the bar, D = 63 mm Velocity of…

Q: The orthogonal cutting of steel is done with 10° rake tool with a depth of cut of 4mm feed rate of…

A: Merchant circle:

Q: An external turning operation is performed on a hollow workpiece of 200 mm external diameter and 100…

A: Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If…

Q: Find the time required for one full cut on a work piece of 350mm long and 20 mm in diameter. The…

Q: O In a production turning operation, the foreman has decreed that a single pass must be completed on…

A: in a production turning operation , the foreman has decreed that a single pass must be completed on…

Q: 1. A 12.5cm long, 5.25mm radius copper alloy rod is being reduced in diameter to 4.25mm by turning…

Q: Make a figure and explain how shear plane angle effect the power requirements in the machining. How…

A: Required :- Explanation of how the shear plane angle affects the power requirements in machining…

Q: A motorised metal guillotine machine is required to cut 45 mm diameter hole in a plate of 20 mm…

A: Given data as per question Diameter =45 mm Thickness =20 mm Torque required =7Nm speed variation of…

Q: length is 1100 mm. The feed is 0.35 mm/rev and the depth of cut is 2.5 mm. The cut will be made with…

A: Given data:-diameter of bar, D=400mmLength of bar, L=1100mmfeed, f=0.35mm/revdepth of cut,…

Q: Calculate the machining time to complete the job as shown below from a bar 120 mm long and 60 mm…

A: Given: length of the job→L=120 mm initial diameter→D=60 mm maximum depth of cut→d=5 mm hence in…

Q: 4) Assuming that the coefficient þf friction is 0.25, calculate the maximum depth of cut for turning…

A: The power of lathe is given as, The coefficient of friction is given as, The mechanical efficiency…

Q: In a turning operation, the workpiece diameter is Dm-40.00 mm and the diameter after the operation…

A: GIVEN DATA - D=40mm D2=24mm V=132m/min f=0.03mm/rev WE HAVE TO CALCULATE MRR

Q: Problem1. In orthogonal tuming of a 50mm dia. mild steel bar on a lathe, the following data were…

A: Given data: The rake angle, α = 15o. The cutting speed, Vc = 100 m/min. The feed rate, f = 0.2…

Q: In orthogonal turning of low carbon steel pipe with principal cutting edge angle of 90°, the main…

A: Given:Feed force, FT=800 NRake angle, α=0o Shear angle, ϕ=25oCutting force, Fc=1000 N

Q: Draw the forces and angles involved in the cutting process and calculate shear angle (0),…

A: We have to calculate force angel and cutting process

Q: *Using the Taylor equation for tool life and Tetting n = 0.5 and C= 400, calculate the percentage…

A: Given that, Tool exponent, n=0.5,Constant, C=400,Cutting speed is reduced by 50 %, Writing Taylor…

Q: Example: A cylinder of 155 mm diameter is to be reduced to 150mm diameter in one turning cut with a…

Q: Assume that, in orthogonal cutting, the rake angle is 20 and the friction angle is 35 at the…

A: Given data Rake angle, α=20 friction angle for case 1 friction angle for case 2

Q: A cylindrical work part 200 mm in diameter and 700mm long is to be turned in an engine lathe.…

A: Given:D=200 mmL=700 mmV=2.3 m/sf=0.32 mm/revd=1.8 mm

Q: In machining a mild steel work piece with carbide tool, the life of the tool was found to be 1 hour…

Q: A 6.5 inch long, 0.5 inch diameter stainless steel rod is being reduced to 0.480 inches by turning…

Q: Manufacturing Processes What is the effect of shear plane angle in metal cutting? Illustrate with…

A: What is the effect of shear plane angle in metal cutting? Illustrate with diagram

Q: An orthogonal cutting operations is being carried out in which uncut thickness is 0.010 mm, cutting…

A: Given:- α=15°FT=25 NFc=60 NChip thickness=0.015mmUncut thickness=0.010Width=6 mm To find:- The ratio…

Q: Explain the distinct features of non-conventional machining which gave it superiority over the…

A: Solution:

Q: In machining a mild steel work piece with carbide tool, the life of the tool was found to be 1 hour…

Q: In an orthogonal turning process, the chip thickness is 0.32 mm , feed is 0.2 mm/rev, then calculate…

A: Given data: The chip thickness is tc = 0.32 mm. The feed is f = 0.2 mm/rev.

Q: Write down the steps required to proof the mathematical relation for SHEAR PLANE ANGLE in Orthogonal…

Q: Example 4.2.2: In a production turning operation, the foreman has decreed that a single pass must be…

A: Given data:

Q: A 400 mm long, 19.5 mm diameter of 304 stainless steel rod (assume specific energy of steel is 4…

Q: An orthogonal cutting operation is being carried out under the following conditions: depth of cut,…

Q: Calculate amount of removed chips in (m³/min), If you have cutting width is 50mm, cutting depth is…

A: Given that: Cutting width = 50 mm Depth of cut = 10 mm Feed rate = 4.15 mm/min It is required to…

Q: of 7 Nm for an area of hole in mm?. If the cutting takes 1/10 of a second and the speed of its…

Question

i need the answer quickly

A hole of 40 mm diameter and 50 mm depth is to be
drilled in a milled steel component. The cutting speed
can be taken as 65 m/min and the feed rate as
0.25mm/rev.
Calculate the machining timt

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Given Data

VIEW

Step 2 Calculation

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The face milling cutter of D = 200 mm used to cut a block which is 200 mm H, 1=480 mm, if f- 0.7 mm/rev is used and the overrun of the cutter is 12 mm and cutting speed 320 mm/min. Calculate the machining time. Cuttin
As the cutting speed for mild steel is 100ft/min and RPM is 1000, find the diameter of the cutting tool. If the tool is two-flute end mill. Then, also find the feed rate. Given, 0.002 in. feed per tooth.
For the operation of straight turning in a lathe machine, the diameter of the workpiece is 80 mm, the length is 0.12 m, the cutting speed is 80 m / min, the feed is 0.5 mm / rev and the depth of cut is 0.002 m . Find the material removing rate and the time of machining.
A shaper is operated at 120 cutting strokes per minute and is used to machine a work piece of 250 mm in length and 120 mm wide. Use a feed of 0.6 mm per stroke and a depth of cut of 6 mm. Calculate the total machining time to for machining the component. If the forward stroke is completed in 230°, calculate the percentage of the time when the tool is not contacting the work piece.
A cylindrical rod is machined using turning processes. It is given that the cutting speed is 120min ¹, and feed per tooth is 0.0025 m/min. The outer diameter is 35mm, the length of the rod is 130m and the inner diameter is 22mm. The number of teeth is 6. Find Rotational speed, Feed rate, Machining time, and Depth of cut.
Quiz A piece of Low carbon steel has (85mm) length machined by a lathe with cutting tool made of HSS, depth of cut (2mm), feed (0.2mm/rev) and (4) number of cycles with (30m/min) cutting speed. If the final diameter is (44mm). calculate the machining time of this piece.
A motorised metal guillotine machine is required to cut 45 mm diameter hole in a plate of 20 mm thickness at rate of 35 holes per minute. It requires a torque of 7 Nm for an area of hole in mm?. If the cutting takes 1/10 of a second and the speed of its flywheel varies from 165 rpm to 145 rpm, calculate: 4.1. Energy required to cut a hole. 4.2. Energy required for cutting work per second.
5.) Calculate the machining time required to reduce from 60mm diameter shaft to 50mm diameter, for a length of 1500mm with depth of cut 2mm for rough cut and 1mm for finish cut. Cutting speed and feed may be assumed as 30m/min and 0.5mm/rev respectively.
Machining time required reduce a mild steel rod of diameter 60mm, initial length (L) 125mm to final length (L1) 120mm to 58 mm by turning a carbide insert. If the approach length and over run length are 5 mm and 1 mm respectively, take Cutting speed as 20 m/min and feed is =0.2 mm/rev, and the depth of cut is 0.5mm
Calculate the machining time to drill four 20 mm diameter holes and one 50 mm diameter central hole in the flange as shown below. Take cutting speed 20 m/min, feed for 20 mm drill 0.2 mm/rev, and for 50 mm drill feed is 0.6 mm/rev, the point angle is 120°? VIVER 20xA 200 D100 SYLON 50
1.10A O50 mild steel bar is being turned at 1.70 revis on a multi-tool center lathe having nine tools. For all tools the depth of cut is 4mm. the feed is 0.255mm/rev, and the specific cutting pressure is 1 545N mm?. Calculate the total power consumed for the operation
In an orthogonal cutting operation an 8 mm deep groove is to be turned on a 50 mm diameter steel bar. Spindle speed is 300 rpm and a feed rate of 0.25 mm/rev is given to the tool. Produced chips have a width of 2 mm. Calculate the material removal rate at the beginning and at the end of the cut. Can u help me please?