A mobile crane is lifting a large concrete block W at a constuction site, as shown in the figure below. The crane body has a weight of W₁ = 8500 lb and the crane boom has a weight of W₂ = 1100 lb, which act at the centers of gravity CG₁ and CG₂ respectively. The center of gravity locations (L₁ & L₂), the distance between the front and rear tires (L3), and the location of the lifting weight (L4) are given as follows: L₁ = 30 in, L2 = 95 in, L3 = 105 in, and L4 = 135 in. Note: Express your answers following the standard sign convention for the coordinate system shown. L₂ y Lox CG₂

A mobile crane is lifting a large concrete block W at a constuction site, as shown in the figure below. The crane body has a weight of W₁ = 8500 lb and the crane boom has a weight of W₂ = 1100 lb, which act at the centers of gravity CG₁ and CG₂ respectively. The center of gravity locations (L₁ & L₂), the distance between the front and rear tires (L3), and the location of the lifting weight (L4) are given as follows: L₁ = 30 in, L2 = 95 in, L3 = 105 in, and L4 = 135 in. Note: Express your answers following the standard sign convention for the coordinate system shown. L₂ y Lox CG₂

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Three hydraulic cylinders control the motion of the backhoe arm and bucket in the given figure. In the position shown, a 18.86-kN horizontal force is applied to the bucket at point L. Assuming the weight of the backhoe arm is negligible compared to forces acting on it, find the force acting on pin A (FA) in kN.
The man in the figure below is pulling a drum over a circular hill. All surfaces are smooth (no friction forces). If the drum weighs 60N, what is the tension on the rope for the drum position shown?
6 in 25 (b A B KLOA of F 1 5in 6 in 20 lb in C 9 in C Be sure to express elbach in and sense (cow // LOA of F₂ 8 in 12 in mag/din cw) for M. 14 in D 1 Two forces and a equivalent system consisting of: • a vertical force I at B ) • a force F₂ at C whose line of action is at 60° to the horizontal couple of moment M and 15 couple act on the plate shown above. Find 1 35 16 form, and give bath the an mag
Use the following figure for both questions below. 1. The end of a tank containing water is vertical and has the shape of the bottom of a half circle of radius 10m. Determine the hydrostatic force against the end of the tank. 2. A milk truck carries milk with density 64.6lb/f in a horisontal cylindrical tank with diameter 6/t. F'ind the force exerted by the milk on one end of the tank when the tank is half full.
Q4: The diagram shows the open bonnet of a car vortical force V ijlull. The bonnet is held open at an angle of 60° to the horizontal by a vertical force V applied at one end of the bonnet (shown on the diagram). The bonnet is 0.90 m long, has a weight of 25 N and its center of gravity G is car bonnet- 0.35 m from the hinge at O. 0.90m 1) On the diagram, draw and label the two forces other than V acting on the bonnet. 635m 2) By taking moments about 0, Proof that the vertical force V applied at the end of the bonnet is 9.7 N. horizonlal - hinge O 3) Calculate the magnitude of the force acting at the hinge O.
Q3/. The portable floor crane in the automotive shop is lifting a 420 lb engine. For the position shown compute the magnitude of the force supported by the pin at Cand the oil pressure pagainst the 3.20 in-diameter piston of the hydraulic-cylinder unit AB. See figure (3). 45 100 Ib te-18 15 3 ft 3 ft- 30 200 lb ft 30 30 30 kg 2 ft B 12 Fig (1) Fig (2) Fig (3)
The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The combined weight of the leg and cast is W=180 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=5 cm. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=30°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) Answerb) Find the tensile force T2 in cable 2. (Write your result in N) Answerc) Find the angle α of cable 1 with the horizontal. Response
A 50 kg pole extends up a wall, making a 60° angle with the wall. The pole is supported by acable attached 3/4 of the way along the pole. This support cable is perpendicular to the wall.A 10 kg sign hangs from the end of the pole. The pole’s center of mass is 1/3 of the way fromthe wall to the end of the pole. (a) What is the tension in the cable?(b) What are the x and y components of the force the wall exerts on the pole?You must include an extended free body diagram showing all forces acting on the pole. Labelthe location on the pole you will use a reference for measuring distances (the “axis of rotation”) at the point where the pole touches the wall. Thank you!
wor The uniform boom shown below weighs 5000 N. It is supported by the horizontal guy wire and by the hinged support at point A. What are the forces on the boom due to the wire and due to the support at A? Does the force at 'A' act along the boom? A 45° 2000 N
A string holds and wraps around a solid cylinder (7-kg and R = 8-m). A person pulls the string vertically upward, so the cylinder's center of gravity does not move and is suspended in midair for 7 second. Note that the rotational inertia of the cylinder about its axis is MR2/2, the tension in the string is 8- N. what is the net force on the cylinder in Newton? Note: Do not include the unit in your answer. T
Consider a floor crane operated by a driver which carries a drum as shown in figure. The total weight of floor crane and driver is 2700 kg acting at the point of center of gravity, G. mm; = 1 = Considering L1 = 14m, L2= 3 m L3 - 6 m, 14 = 2 m LS = 1 m; L6=7m 1. If the weight of the drum lifted by the floor crane is 800 kg, determine the total normal reaction on the rear wheels at A and total normal reaction on the front wheels at B when the boom is inclined at an angle of 25" with the horizontal, 2. Utilizing the same data given above for the same position of boom, determine the largest weight of the drum that can be lifted without causing the crane to overturn. (Hint: When the floor crane tends to overturn about point B, the wheel at A will leave the ground). Note: 1. Consider the entire system as coplanar 2. Take g 9.81 m/s wherever necessary = 9 Total normal reaction on the rear wheels at A= Total normal reaction on the front wheels at B= Largest weight of the drum=
What would be the maximum weight W of the block, shown in the following figure, so that the tension developed in any cable does not exceed 700 N: 30° 40°/ В Activate Windows G to Setinas lo activate Wdoud Shew ll urban-chap1.2.3.pdf urban-chap1.2.3 (1) pdf 132 AM ipd(2): A d0 ENG 4/18/21