A plane wall 15 – cm thick has a thermal conductivity given by the relation k = 2.0 + 0.0005 T, W/m – K where T is in Kelvin. If one surface of this wall is maintained at 150 oC and the other at 50 oC, determine the rate of heat transfer per square meter. Sketch the temperature distribution through the wall.

A plane wall 15 – cm thick has a thermal conductivity given by the relation k = 2.0 + 0.0005 T, W/m – K where T is in Kelvin. If one surface of this wall is maintained at 150 oC and the other at 50 oC, determine the rate of heat transfer per square meter. Sketch the temperature distribution through the wall.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.4P: A plane wall 15 cm thick has a thermal conductivity given by the relation k=2.0+0.0005T[W/mK] where...

See similar textbooks

Similar questions

A plane wall 15 cm thick has a thermal conductivity given by the relation k=2.0+0.0005T[W/mK] where T is in kelvin. If one surface of this wall is maintained at 150C and the other at 50C, determine the rate of heat transfer per square meter. Sketch the temperature distribution through the wall.
Discuss the modes of heat transfer that determine the equilibrium temperature of the space shuttle Endeavour when it is in orbit. What happens when it reenters the earths atmosphere?
1.10 A heat flux meter at the outer (cold) wall of a concrete building indicates that the heat loss through a wall of 10-cm thickness is . If a thermocouple at the inner surface of the wall indicates a temperature of 22°C while another at the outer surface shows 6°C, calculate the thermal conductivity of the concrete and compare your result with the value in Appendix 2, Table 11.
A pipe carrying superheated steam in a basement at 10C has a surface temperature of 150C. Heat loss from the pipe occurs by radiation (=0.6) and natural convection (hc=25W/m2K). Determine the percentage of the total heat loss by these two mechanisms.
What are the important modes of heat transfer for a person sitting quietly in a room? What if the person is sitting near a roaring fireplace?
The heat transfer coefficient between a surface and a liquid is 57 W/(m2K). How many watts per square meter will be transferred in this system if the temperature difference is 10C?
Q: A large plane wall of thickness (L= 0.3 m), thermal conductivity (k = 40 W/m-°C), and surface area 0.4 m2. The left side of the wall is maintained at a constant temperature of 70°C while the right side loses heat to the surrounding air with heat flux q' expressed by: 1200k q = k+20L A- Find a relation to determine the variation of temperature in the wall. B- Determine the rate of heat transfer through the wall. C- Determine the temperature at the right side of the wall. wall T1= 70 °C L= 0.3m
5- Determine the rate of heat transfer by conduction per unit area, by means of conduction for a furnace wall made of fire clay. Furnace wall thickness is 6" or half a foot. Thermal conductivity of the furnace wall clay is 0.3 W/m-K. The furnace wall temperature can be taken to be same as furnace operating temperature which is 650°C and temperature of the outer wall of the furnace is 150°C.
GChoose the right answer 1. The temperature profile for steady hest conduction through a plane wall of constant thermal conductivity is a. logarithmic b. parabolic 2. A brick wall (k-0.75 W/mK ) transmits $02 of heat loss through another wall (k-0.25 W/mK, x-100 mm). If the temperature difference across both walls is the same, the thickness of the brick wall would be a.150 mm c. linear 6T b. 240 mm c. 300 mm d. 375 mm 3. The maximum temperature at the center of the solid sphere of radius R having heat generation q (W/m') is given by g'R +9R b. T, + 4k T+9R 6k d. T+9R 8k a. 2k C. 4. The internal thermal resistance of a solid can be ignored if the Biot number is less than a. 1 b. 0.5 c. 0.1 d. Fourier number 5. The ratio of heat transfer of a fin to the heat transfer without fin is referred to as a. fin resistance b. fin efficieney efin effectiveness d. fin conductance.
1- Consider steady- state conduction for one-dimensional conduction in a plane wall having a thermal conductivity k=50 W/m.K and a thickness L-0.25 m, with no internal heat generation. Determine the heat flux and the unknown quantity (blanks) for each case and sketch the temperature distribution, indicating the direction of heat flux. Case TI(°C) 50 T2(°C) -20 dT/dx(K/m) 1 -30 -10 70 160 40 -80 5 30 200 234n
Consider steady-state conditions for one-dimensional conduction in a plane wall having a thermal conductivity k = 40 W/m-K and a thickness L = 0.3 m, with no internal heat generation. T1 -T2 L Determine the heat flux, in kW/m?, and the unknown quantity for each case. Case T1(°C) T2(°C) dT/dx(K/m) q (kW/m?) 1 50 -20 -233.333 9333.32 2 -30 -10 66.667 75466.67 3 70 117.85 160 6400 4 63.85 40 -80 3200 5 -30.15 30 200 8000
A large plane wall has a thickness of 0.4 m, thermal conductivity k= 2.3 W/m. °C, and surface area 30 m?. The left side of the wall is maintained at a constant temperature of 90°C while the right side loses heat by convection to the surrounding air at 25°C with a heat transfer coefficient of 24 W/m². °C. Assuming constant thermal conductivity and no heat generation in the wall, (i) Express the differential equation and the boundary conditions for steady one-dimensional heat conduction through the wall (ii) Obtain a relation for the variation of temperature in the wall (iii) Evaluate the rate of heat transfer through the wall