A sample of ocean sand was retrieved from 7 m below the surface. The sample had been under a vertical stress Ov of 150 kN/m³, a horizontal stress Oh of 250 kN/m³, a shear stress of 86.6 kN/m. If the angle theta between the vertical stress and the principal stress is 60°, calculate the angle of internal friction of the soil. [

A sample of ocean sand was retrieved from 7 m below the surface. The sample had been under a vertical stress Ov of 150 kN/m³, a horizontal stress Oh of 250 kN/m³, a shear stress of 86.6 kN/m. If the angle theta between the vertical stress and the principal stress is 60°, calculate the angle of internal friction of the soil. [

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter10: Shear Strength Of Soil

Section: Chapter Questions

Problem 10.10P

See similar textbooks

Similar questions

2. The state plane stress in a mass of dense cohesionless sand (c=0) is described by the following stresses: Normal stress on horizontal plane = 100 kPa Normal stress on vertical plane = 50 kPa Shear stress on horizontal and vertical planes = ± 30 kPa Determine by means of the Mohr circle the magnitude and direction of the principal stresses. Is this state of stress safe against failure assuming φ= 30o?
The angle of friction of a compacted dry sand is 37 degrees. In a direct shear test on the sand, anormal stress of 150 kN/m^2 was applied. The size of the specimen was 50mmx50mx30mm(height) SITUATION 1 a. Compute the shearing stress Your answer b. What shear force will cause shear failure? Your answer c. Determine the shear stress at a depth of 3m if the void ratio of the soil is 0.60. Gs Of sand is 2.70
A triaxial shear test was performed on a well-drained sand sample. The normal stress on the failure plane and the shear stress on the failure plane, at failure were determined to be 6100 psf and 4600 psf, respectively. a. Determine the angle of internal friction of the sand? b. Determine the angle of the failure plane? c. Determine the maximum principal stress? Please answer this asap. For upvote. Thank you very much
1.A dry sand is known to have an angle of internal friction of 29. A triaxial test is planned, where the confining pressure will be 41 kPa. What is the maximum axial stress, in kPa, (major principal stress) that can be applied? Calculate the value to 1 decimal place. Do not provide units in your answer. 2.A clay soil is subjected to a triaxial test under unconsolidated-undrained conditions. At failure, the major and minor principal stresses are 8401 psf and 4875 psf, respectively. What is the shear strength of this soil if the confining pressure is doubled? Provide your answer in psf with no decimals.
2. A series of consolidated, undrained triaxial tests were carried out on specimens of a saturated clay under no backpressure. The test data at failure are summarized: Confining Pressure (kPa) Deviator Stress (kPa) Pore Water Pressure (kPa) 150 192 80 300 341 154 450 504 222 a. Draw the Mohr circles and find the cohesion and friction angles in terms of effective stresses. b. Compute Skempton’s A-parameter at failure for all three specimens. c. Is the soil normally consolidated or overconsolidated? Why? d. Another specimen of the same clay that was consolidated under a cell pressure of 250 kPa was subjected to a consolidated, drained triaxial test. What would be the deviator stress at failure?
At failure, the major and minor principal stresses on a triaxial test are 200 kPa and 110 kPa respectively. If the porewater pressure at failure is 25 kPa... Q: What is the sine of the angle of shearing resistance of the soil? Round off your answer to two decimal places.
The normal stresses acting on two orthogonal planes of a soil sample are 250 kN/m2 and 110 kN/m2 a. Major principal stress b. Minor principal stress c. Normal stress on a plane inclined 60° to the direction of the major principal stress d. Shear stress on a plane inclined 60° to the direction of the major principal stress
A soil specimen is subjected to tri axial test. The soil specimen is cohesion less. If the shear stressthat causes failure is 335 KPa and the normal stress at failure is only 435 KPa, determine the following:1. Angle of shearing resistance.2. Angle that the failure plane measured from the major principal plane.3. Total axial stress at which failure is expected to occur.
A soil specimen is subjected to a tri – axial test. The soil specimen is cohesionless. If the shear stress that causes failure is 300 kPa. and the normal stress at failure is only 500 kPa 5. Determine the angle of shearing resistance in degrees 6. Determine the angle that the failure plane measured from the major principal plane. 7. Determine the total axial stress in kPa at which failure is expected to occur.
A specimen is subjected to a tri-axial test. The soil specimen is cohesionless. If the shear stress that cause failure is 3oo kPa and the normal stress at failure is only 475 kPa. 1. Determine the angle of shearing resistance. 2.Determine the angle that the failure plane measured from the major principal plane 3.Determine the maximum principal stress at which failure is expected to occur
10-14. The state plane stress in a mass of dense cohesionless sand is described by the following stresses: Normal stress on horizontal plane Normal stress on vertical plane = 200 kPa Shear stress on horizontal and vertical planes 370 kPa 80 kPa %3! Determine by means of the Mohr circle the magnitude and direc- tion of the principal stresses. Is this state of stress safe against failure? (After A. Casagrande.)
Assume that both a triaxial shear test and a direct shear test are to be performed on a sample of dry sand. When the triaxial shear test is performed, the specimen fails when the major and minor principal stresses are 80 and 20 lb/in.2, respectively. When the direct shear test is performed, what shear strength can be expected if the normal stress is 4000 lb/ft2?