A square pedestal has glued parts at joints t, r, e, and s. Plane t-r-e-s is at anole of 30° from the vertical axis Given the following data: allowable pressive stress of 5.2 MPa in glued joint and Shear stress of 3.5 MPa. If the axial pedestal force is 36 kN. determine the safe width dimension in mm and the angle in degrees if the maximum shear stress will occur to the plane

A square pedestal has glued parts at joints t, r, e, and s. Plane t-r-e-s is at anole of 30° from the vertical axis Given the following data: allowable pressive stress of 5.2 MPa in glued joint and Shear stress of 3.5 MPa. If the axial pedestal force is 36 kN. determine the safe width dimension in mm and the angle in degrees if the maximum shear stress will occur to the plane

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.5.11P: The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in...

See similar textbooks

Similar questions

The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A sign is supported by a pipe (see figure) having an outer diameter 110 mm and inner diameter 90 mm. The dimensions of the sign are 2.0 m X 1.0 m, and its lower edge is 3.0 m above the base. Note that the center of gravity of the sign is 1.05 m from the axis of the pipe. The wind pressure against the sign is 1.5 kPa. Determine the maximum in-plane shear stresses due to the wind pressure on the sign at points /I, B, and C, located on the outer surface at the base of the pipe.
A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.
A 2.4 diameter steel molding is lifted by 4 steel cables as shown. The mold weighs 3 kN/m. (a) what is the required diameter of wire that will not exceed the allowable stress of 120 MPa. and (b) if the wire diameter increase by 20%, find the vertical displacement of the molding. 24m
A 150 mm x a mm x 20 mm steel plate is subjected a pull of 150 kN along its central axis as show in figure. A hole of 40 mm diameter is drilled in the plate whose center is 50 mm alway from central longitudinal axis. Calculate the max stress in the plate. 20 min 40 min 40 nun 75 mm 50 mm 150 kN I50 km 75 mm
Mohr's circle for an element is shown, each grid is 5 MPa square. A rotated plane through the element is also shown as the line nt. The shear stress on the plane that is rotated from the x face is: 1 rid square =5 MPa
For the stresses given with the cube below: 1. Compute the center, radius (R), principal normal stresses (0₁ and 03), max shear stress (Tmax) and draw the Mohr's Circle. 2. Compute the normal and shear stresses when the cube is rotated 20° clockwise from the horizontal plane and draw them on the cube. 3. The yield point stress (σyp) is 6 kPa. Determine if the material will fail under stresses shown using Tresca's Hexagon. вкра акра 6 экра 8 кра экра 4кра
The vertical load P acting on the wheel of a traveling crane is 13,000 lb. What is the average shear stress in the 1.25 in. diameter axle?
Solve for the indentation diameter if the BHN of the material is 70 and a 500 kg of load is applied? Use indenter diameter 10mm.
Mohr's circle for an element is shown, each grid is 5 MPa square. A rotated plane through the element is also shown as the line nt. The normal stress on the plane that is rotated from the x face is: I grid square = 5 MPa
A square post which is made up of two parts is glued atplane ABCD with the angle α = 30° with the vertical.Allowable compressive stress @ glue = 5.2 MPaAllowable shearing stress = 3.5 MPaP = 36 kN. 1. What is the minimum post dimension, w (mm), withoutexceeding the allowable shearing stress at the glue? 2. What is the minimum post dimension, w (mm), withoutexceeding the allowable compressive stress at the glue? 3. What angle, α, will give the maximum shearing stress? with brief explanation each part
A shaft 30 mm diameter is transmitting power at a maximum shear stress of 80 MPa. If a pulley is connected to the shaft by means of a key, find the dimensions of the key so that the stress in the key is not to exceed 50 MPa and length of the key is 4 times the width.