A steel girder of 6m length acting as a beam carries a uniformly distributed load w N/m run throughout its length. If I = 30 × 10-6 m and depth 270 mm, сalculate: (i) The magnitude of w so that the maximum stress developed in the beam section does not exceed 72 MN/m2. (ii) The slope and deflection (under this load) in the beam at a distance of 1.8 m from one end. Take : E = 200 GN/m2 %3D

A steel girder of 6m length acting as a beam carries a uniformly distributed load w N/m run throughout its length. If I = 30 × 10-6 m and depth 270 mm, сalculate: (i) The magnitude of w so that the maximum stress developed in the beam section does not exceed 72 MN/m2. (ii) The slope and deflection (under this load) in the beam at a distance of 1.8 m from one end. Take : E = 200 GN/m2 %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3) Find the maximum shear stress. 4) Find the deflection midway between the supports. 4 kN/m 5 kN 1m 2 kN.m 2m 2m 2m 2m 5 mm E=200 GPA 20 mm 50 mm- Beam Cross-Section
A) Define the bending stress as relates of beams. B)A fixed AB length 3m carries a point load of 45KN at a distance of 2m from A.if the flexural rigity (i.e. EL)is 1×10^4KNm^2, determine: I) fixed end moment A and B II) Deflection under the load III) the maximum deflection IV) The position of the maximum deflection.
4. A 10 m span simply supported beam carries a uniform load. The beam has an adequate lateral support. ALLOWABLE STRESSES: Bending: 12.65 MPa Deflection: 1/240 of span E: 13000 MPa a. Compute the depth of the beam so that when the allowable stresses of 12.65 MPa is reached, The deflection of the beam is 1/240 of the span. b. If the width of the beam is 300mm, how much total uniform load can it simply support? c. Compute the shearing stress of the beam using the uniform load in letter b. W (kN) lom 12 R
PROBLEM 6 The rigid bar DC below is horizontal under no load, and bars A and B are unstressed. When the load P is applied, the strain in bar B is found to be 0.0015. Determine (a) the factor of safety with respect to failure by slip for bar A. (b) The load P (c) The vertical displacement (deflection) of point C. E B A C 100 mm 100 mm 50 P. 200 mm 375m m
Situation 12: A rectangular reinforced concrete beam having a width of 200 mm and an effective depth of 500 mm is subjected to a service moment of 120 kN-m The beam is reinforced with four 25-mm diameter bars. The modular ratio n = 8. Use Working Stress Design. 30. Which of the following most nearly gives the distance of the neutral axis from the top of the beam? a. 212.51 mm b. 233.09 mm 31. Which of the following most nearly gives the stress inn concrete? c. 241.89 mm d. 226.57 mm а. 11.83 МРа b. 12.19 МPа с. 13.16 MPа d. 12.48 MPa 32. Which of the following most nearly gives the stress in the steel? a. 145.73 MPa b. 142.41 MPa c. 143.98 MPa d. 144.72 MPa
Concentrated loads P area acting at the middle thirds of the beam having a span of 9- m. The beam is made up of a wide flange with a yield strength of 344.5 MPa and a modulus of elasticity of 200,000 MPa. The beam is laterally supported only every 3 m distance. Neglect the weight and deflection of the beam. bf = 368.8 mm d = 356.11 mm tf = 18.03 mm tw = 11.18 mm Sx = 2343 x 103 mm4 a) Which of the following gives the value of allowable bending stress. b) Which of the following gives the safe value of "P" in flexural stress control design.
The simply supported bearn consists of a W530 × 66 structural steel wide-flange shape [E = 200 GPa; 1= 351 x 10 mm4]. Determine the beam deflection at point A. (a) (b) the beam deflection at point C. Assume P = 29 KN, w = 69 kN/m, LAB = 4.6 m, Lec=4.6 m, Lco=4.6 m, LDE = 2.3 m. Answer: VA= P VC= B LAB LBC mm mm LCD W D LDE E X
No. 3. Beam AC carries a concentrated load P at its midspan point B. Determine the depth of the beam h in mm if the maximum bending stress is Omax = 50 MPa, the maximum deflection 8max = 10mm, the span is L = 4m, and the modulus of elasticity is E = 200 GPa. L/2 L/2- B 4+ 18. max
Problem (5) The simply supported beam AB is used to support the following loadings as shown. Weight for the beam is neglected. Determine the internal forces at: • Point C located at distance 2m from A. Point D. 10KN 2 AN/m 5 m 3m -2m-
The simple beam with a height of 200mm, a width of 100mm and a length of 4m is loaded as shown. Do the following: 4. Determine the maximum flexural stress; 5. Determine the maximum flexural stress at a section 2.5m from the left end. 6. Determine the maximum shear stress; 7. Determine the shear stress at a section 3m from the left end; 8. Determine the deflection at 2m from the left end. 9. Determine the slope at A. 10. Draw the elastic curve.
Plane frame below is analysed by neglecting axial deformations. Following statements are made w.r.t the analysis 5 m 5 m 10 kN/m El = 81380 kN-m² 7m I. Column AB carries axial force only II. Vertical deflection at the centre of beam BC is 1 mm With reference to the above statements, which of the following applies? (a) Both the statements are true (b) Statement I is true but II is false (c) Statement II is true but I is false (d) Both the statements are false
1. A composite axial structure consists of two rods joined at flange B. Rods (1) and (2) are attached to rigid supports at A and C, respectively. A concentrated load P is applied to flange B in the direction shown. Determine the internal forces and stresses in each rod. Indicate T or C. Also, determine the deflection of flange B in the x-direction