A torque T-800Nm is applied as shown to shaft CD. Shafts AB and CD have cross-sectional diameters d=40mm and shear modulus G-75 GPa. Shaft A is anchored at support A which permits no twisting. The supports at E, F, and G exert no torques on the shaft. a. Calculate the maximum shear stress in shaft AB; b. Calculate the maximum shear stress in shaft CD; c. Calculate the twist angle in the shaft at D.

A torque T-800Nm is applied as shown to shaft CD. Shafts AB and CD have cross-sectional diameters d=40mm and shear modulus G-75 GPa. Shaft A is anchored at support A which permits no twisting. The supports at E, F, and G exert no torques on the shaft. a. Calculate the maximum shear stress in shaft AB; b. Calculate the maximum shear stress in shaft CD; c. Calculate the twist angle in the shaft at D.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A alm T 1.20 m T B 1.20 m C 3 T The 60 mm diameter shaft is made of 6061-T6 aluminum having an allowable shear stress of Tallow 80 MPa. Find the corresponding angle of twist of disk A relative to disk C. Note: You will need to calculate the maximum allowable torque T first. Provide your answer for angle of twist in radians with 3 significant figures after the decimal point.
Shafts AC and DE have 50 mm radius and shear modulus G=79.3 Gpa. 60kN.m Torque is applied to end E and 25 kN.m Torque to gear D .Find the angle of twist of at E of shaft DE. Please consider the twist directions.
Q.12A solid shaft of diameter 'd' and length " issubjected to torque T. Another shaft B ofsome length, material but twice the diameter is subjected to the torque 2T. The ratio of the angle of twist of shaft A to shaft B is-
The copper shaft is hollow from A to B and the steel shaft is solid from B to C. The shaft has an outer diameter of 100 mm, and the thickness of the wall of the hollow segment is 20 mm, take Gst = 100 GPa. & Gcopp. = 60 GPa. The angel of twist of B is %3D steel 8 KN.m Copper 5 KN.m 3 m a. 0.076 Rad b. 0.053 Rad C. 0.0292 Rad d. 0.0175 Rad
Design a hallow shaft (Diameter and length) that develops 80 kN of power while rotating at a speed of 4000 rpm. The design constrains are as under: The angle of twist not to exceed 0.200 Shear stress is not to exceed 480 MN/m? The outer diameter is to be twice the inner diameter. The shaft length is to be three times the outer diameter. Modulus of rigidity = 79 GN/m?.
The solid aluminum shaft ABCD carries the three torques shown.Determine:(a) the smallest safe diameter of the shaft if the allowable shear stress is 15 ksi.(b) Compute the angle of rotation of end A of the shaft using G = 4 x 10^6 ???.
A steel shaft is to be manufactured either as a solid circular solid bar or as a circular tube. The shaft is required to transmit a torque of 1200N-m without exceeding an allowable shear stress of 40MPa or an allowable rate twist of 0.75deg/m. The shear modulus of steel is 78GPa. Compute the required diameter of the solid shaft & compute the required outer diameter of the hollow shaft if its thickness is 1/10 of its outer diameter.
A motor driving a solid circular steel shaftwith diameter d = 1.5 in. transmits 50 hp to a gear atB. The allowable shear stress in the steel is 6000 psi.Calculate the required speed of rotation (number ofrevolutions per minute) so that the shear stress in theshaft does not exceed the allowable limit.
A solid circular shaft is acted upon by thetorques as shown. If G= 12, 000 ksi determine:a. Rotation of wheel D with respect to A.b. Shear stress at point EDiameter of shaft:A-B = 2inC-D = 2inB-C = 4inT1 = 2.5 π in.kipsT2 = 8.5 π in.kipsT3 = 7 π in.kipsT4 = π in.kips
A steel shaft with a diameter 1.85 inches and length 4.25 feet transmits 75 HP from an electric motor to a compressor. The allowable shear stress is 7500 psi and the allowable angle of twist is 2.1 Degress. G= 12x10^6Deterrmine the following: (No Scientific Notation answers) a. Determine the polar moment of inertia (in in^4) of the steel shaft: b. Determine the required torque (in lb-in) as limited by stress: c. Determine the required torque (in lb-in) as limited by the angle of twist: d. Determine the minimum allowable speed of rotation (in rpm):
A shaft is designed to transmit power of 100 kW at 180 rpm. The allowable shear stress is 50MPa and modulus of rigidity of 80 GPa. The angle of twist is not to exceed to 1° in 4-meter length A. Calculate the diameter of the shaft in inches. B.If the shaft in A is to be fitted to a hub with material SAE 0105 and fit classification of FN3, what will be the maximum and minimum stresses based on the interference of metal.
A hollow bronze shaft of 75 mm outer diameter and 50 mminner diameter is slipped over a solid steel shaft 50 mm indiameter and of the same length as the hollow shaft. The twoshafts are then fastened rigidly at their ends. Find the maximumshearing stress developed in the bronze by end torque of 3 kN.mFor bronze G = 35 GPa and for steel G = 83 GPa.