Consider the following beam with overhangs:AВCL.Calculate the deflection at A (the end opposite of the load) and at D (under the load). Assume that both deflections are downward. The answers will be of the formX .PLEIYou must provide the value of X. For example, if the answer is 0.ET, enter "0.05" (1/20) in the Canvas quiz.PL3Here are a few hints. You'll have to break up the integral over three segments (A to B, B to C, and C to D). On several spans, one of the moment diagrams will bezero. Remember that the definite integral of zero is equal to zero, i.e., ° Odx = 0. All the remaining integrals should involve triangles with integration factors of1/3 and 1/6.

A В C L L. Calculate the deflection at A (the end opposite of the load) and at D (under the load). Assume that both deflections are downward. The answers will be of the form PL3 X. EI You must provide the value of X.For example, if the answer is , enter "0.05" (1/20) in the Canvas quiz. 20-EI Here are a few hints. You'll have to break up the integral over three segments (A to B, B to C, and C to D). On several spans, one of the moment diagrams will be S° Odx = 0. All the remaining integrals should involve triangles with integration factors of zero. Remember that the definite integral of zero is equal to zero, i.e., 1/3 and 1/6.

A В C L L. Calculate the deflection at A (the end opposite of the load) and at D (under the load). Assume that both deflections are downward. The answers will be of the form PL3 X. EI You must provide the value of X.For example, if the answer is , enter "0.05" (1/20) in the Canvas quiz. 20-EI Here are a few hints. You'll have to break up the integral over three segments (A to B, B to C, and C to D). On several spans, one of the moment diagrams will be S° Odx = 0. All the remaining integrals should involve triangles with integration factors of zero. Remember that the definite integral of zero is equal to zero, i.e., 1/3 and 1/6.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

(Figure 1), a = 45 mm. re 50 mm 150 mm 150 mm 300 mm 1 of 1 ▾ Part A Locate the centroid y of the beam's cross-sectional area. Express your answer to three significant figures and incle Value Submit HA Provide Feedback mm Previous Answers Request Answer ? X Incorrect; Try Again; 5 attempts remaining
Numerical Solution of Algebraic Equations (Roots of Equations) 5: The deflection of the shown beam is given as: qL x 9x 7x y= 120EI 2L Given that L=3m, q=60KN /m, and El = 6000KN.m2, find numerically the value of the maximum deflection. (Accuracy& =1x10) L
determine the deflection at C in mm using Conjugate Beam Method. Consider 150 mm x 200 (b x h) mm section and E=80 GPa. Enter the absolute value only and round off your answer to 3 decimal places answer asap.
Give the following problem a try. If you get stuck, here is one way to work it: Essential Solution Video. For the beam shown, calculate the beam deflection at A. Assume that a = 2.9 ft, b = 4.4 ft, c 5.8 ft, w= 1550 lb/ft, P = 2700 lb, and El = 571000 kip-in.?. a Answer: VA= in.
determine the deflection at E in mm using Double Integration Method Consider 150 mm x 150 mm section and E=200 GPa Enter the absolute value only and round off your answer to 3 decimal places PLS. ANSWER ASAP, I'LL RATE. THANKS
The intensity of the distributed load on the simply supported beam varies linearly from zero to w0 = 438 lb/ft. What is the maximum value of EIv if L = 9.1 feet . Express your answer in 5 decimal places. Use appropriate sign based on the deflection of the beam. NOTE: PLEASE ANSWER IT CORRECTLY. IF YOU ARE NOT SURE ABOUT THE ANSWER, PLEASE SKIP THE QUESTIONPLEASE BOX THE FINAL ANSWER(S)THANK YOU!
9. Write the deflection equation. Place your answer in a box. 10. What is the deflection at the pin and at point D?Box your answer.
determine the deflection at B in mm using Double Integration Method. Consider 150 mm x 150 mm section and E=200 GPa. Enter the absolute value only and round off your answer to 3 decimal places. PLS ANSWER ASAP. I'LL RATE, THANKS!
Using any of the three Geometric Methods, answer the following beam. Indicate the negative sign (-) if the answer is downward. Provide complete solutions. Write legibly. Box your final answer at the first page of your solution file. Determine the deflection at the free end. Use E= 29x10³ ksi; I = 40 in %3D 41 k/ft 15 k/ft 12 k 30 k-ft C 8 m 2 m
The intensity of the distributed load on the simply supported beam varies linearly from zero to w0 = 446 lb/ft. Find the location of the maximum deflection if L = 8.6 feet . Express your answer in 5 decimal places. NOTE: PLEASE ANSWER IT CORRECTLY. IF YOU ARE NOT SURE ABOUT THE ANSWER, PLEASE SKIP THE QUESTIONPLEASE BOX THE FINAL ANSWER(S)THANK YOU!
Assume that wo = 44 N/m, L = 3.4 m, and El = 26719 for the beam. Find the deflection (in mm) at the portion of the beam 2.47 m from point A. Express your final answer in 5 decimal places. ... A В L Add your answer
10.13 A cantilever beam is loaded with force P at its free end to produce a deflection CHAPTER 10: Materials Selection 391 S- PL/3EI. The beam has a circular cross section, I = ar'/4. Develop a figure of nerit for selecting a material that minimizes the weight of a beam for a given stiffness (PIS), By using the following material properties, select the best material (a) on the basis of performance and (b) on the basis of cost and performance. %3D Material GNM2 ksi P, Mgm Approx. Cost, $/ton (1980) Steel 200 29 x 10 7.8 450 Wood 9-16 1.7 x 10' 0.4-0.8 450 7.3 x 10' 10 x 10 15 x 10 Concrete 50 2.4-2.8 300 Aluminum 69 2.7 2,000 Carbon-fiber- 70-200 1.5-1.6 200,000 reinforced plastic (CFRP)