A Y-connected balanced three-phase generator with an impedance of 0.4 +j0.3 2 per phase is connected to a Y-connected balanced load with an impedance of 24 +j19 N per phase. The line joining the gen- erator and the load has an impedance of 0.6+ j0.7 2 per phase. Assuming a positive sequence for the source voltages and that Van 120/30° V, find: (a) the line voltages, (b) the line currents.

A Y-connected balanced three-phase generator with an impedance of 0.4 +j0.3 2 per phase is connected to a Y-connected balanced load with an impedance of 24 +j19 N per phase. The line joining the gen- erator and the load has an impedance of 0.6+ j0.7 2 per phase. Assuming a positive sequence for the source voltages and that Van 120/30° V, find: (a) the line voltages, (b) the line currents.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.42P: A balanced -connected impedance load with (12+j9) per phase is supplied by a balanced three-phase...

See similar textbooks

Similar questions

The three-phase source line-to-neutral voltages are given by Ean=100,Ebh=10+240, and Ecn=10240volts. Is the source balanced? (a) Yes (b) No
The one-line diagram of a three-phase power system is shown in the above figure. The line impedances are in per- unit on a 100-MVA base, and the line admittances are neglected. Use Gauss-Seidel method in Matlab to analyze the system the tolerance of error is 10-3. Then anwser the questions as follows. V, = 1.05200 0.01+ j0.025 300 + j200 MVA 0.015 + j0.035 150 MW 200 +j150 MVA 0.01+ j0.03 |V = 1.03 The admittance matrix (Y_bus)? 0.02 + jo.04 0.0125 + jo.03 2.
AC Power and Power Factor 1. Two loads are connected in parallel across a 13,200-volt line. Load A draws 200kW at 0.6 p.f. (lagging), load B takes 200kVA at 0.8 p.f. (lagging). Find the reactive, apparent and true power and the line current.
Q2) A 13.2-kV single-phase generator supplies power to a load through a transmission line. The load's impedance is Ztoad 500 236.87° ohm , and the transmission line's impedance is Zine = 60 253.1° ohm. To reduce transmission line losses to 0.0103 of its losses without using the transformers design and use two transformers T1 between the generator and the transmission line and T2 between the transmission line and the load.
Suppose that a current source with Is amperes of current is connected in parallel to a pair of impedances Z₁ and Z2. Let I₁ be the current through Z₁ and 12 be the current through Z₂. Then, the total voltage Is is divided between 1₁ and 12 in proportion to impedance values Z₁ and Z2. a. True O b. False
The one-line diagram of a three-phase power system is shown in the above figure. The line impedances are in per- unit on a 100-MVA base, and the line admittances are neglected. ' qu V = 1.05200 0.01+ j0.025 300 + j200 MVA 3 0.015 + j0.035 150 MW 200 + j150 MVA 0.01 + j0.03 |V = 1.03 The admittance matrix (Y_bus)? The bus power in per-unit?
Draw a 3-phase wye-connected generator with transmission lines connected to a 3-phase delta-connected load. Assume the lines connecting them have an inductance of j5 per phase. The generated voltages are 120 Vrms with phase 'a' having a phase angle of 0°. The loads are 10 Ohm resistors per phase. When drawing, make sure to label all 3 phases with voltage phasors, line inductances, and load resistances.
A balanced Y-connected generator with terminal voltage Vbc 5 200/08 volts is connected to a balanced-D load whose impedance is 10/408 ohms per phase. The line impedance between the source and load is 0.5/808 ohm for each phase. The generator neutral is grounded through an impedance of j5 ohms. The generator sequence impedances are given by Zg0 5 j7, Zg1 5 j15, and Zg2 5 j10 ohms. Draw the sequence networks for this system and determine the sequence components of the line currents.
Q2) A 13.2-kV single-phase generator supplies power to a load through a transmission line. The load's impedance is Zload = 500 236.87° ohm, and the transmission line's impedance is Zline = 60 253.1° ohm. To reduce transmission line losses to 0.0103 of its losses without using the transformers design and use two transformers T1 between the generator and the transmission line and T2 between the transmission line and the load.
an a transmission line has an impedance of 4 j2 Ohms/phase, Find the per-unit impedance of this line on a base of 100 MVA and 20 KV. Select one: O a. None of these Ob. 20-j10 (p.u) Oc 1-0.5 (p.u) O d. 0.5-j1 (p.u)
Two balanced loads are connected to the a 240kVrms60Hz line as shown in the figure below. Load 1 draws30kW at a power factor of 0.6 lagging and load 2 draws 45 kVAR at power factor of 0.8 lagging. The real power, reactive power, and magnitude of the line current absorbed by the combined load is close to kW, kVAR, and A. Two balanced loads are connected to the a 240kVrms 60Hz line as shown in the figure below. Load 1 draws 30kW at a power factor of 0.6 lagging kW. and load 2 draws 45KVAR at power factor of 0.8 lagging. The real power absorbed by the combined load is close to Balanced load 1 Balanced load 2
10 Ω m I₁ j4 Ω + I₂ ~ Vs E₁ || 2:1 The load on the right is absorbing 650 W -j200 VAR. V₁ = 80 / 0° V. + V₁ I