A Y-connected balanced three-phase generator with an impedance of 0.4 + j0.3 N per phase is connected to a Y-connected balanced load with an impedance of 24 + j19 N per phase. The line joining the gen- erator and the load has an impedance of 0.6 + j0.7 N per phase. Assuming a positive sequence for the source voltages and that V 120/30° V, find: (a) the line voltages, (b) the line currents. an

A Y-connected balanced three-phase generator with an impedance of 0.4 + j0.3 N per phase is connected to a Y-connected balanced load with an impedance of 24 + j19 N per phase. The line joining the gen- erator and the load has an impedance of 0.6 + j0.7 N per phase. Assuming a positive sequence for the source voltages and that V 120/30° V, find: (a) the line voltages, (b) the line currents. an

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.42P: A balanced -connected impedance load with (12+j9) per phase is supplied by a balanced three-phase...

See similar textbooks

Similar questions

A balanced -connected impedance load with (12+j9) per phase is supplied by a balanced three-phase 60-Hz,208-V source, (a) Calculate the line current, the total real and reactive power absorbed by the load, the load power factor, and the apparent load power, (b) Sketch a phasor diagram showing the line currents, the line-to-line source voltages, and the -load currents. Use Vab as the reference.
The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
Suppose that a current source with Is amperes of current is connected in parallel to a pair of impedances Z₁ and Z2. Let I₁ be the current through Z₁ and 12 be the current through Z₂. Then, the total voltage Is is divided between 1₁ and 12 in proportion to impedance values Z₁ and Z2. a. True O b. False
Q2) A 13.2-kV single-phase generator supplies power to a load through a transmission line. The load's impedance is Ztoad 500 236.87° ohm , and the transmission line's impedance is Zine = 60 253.1° ohm. To reduce transmission line losses to 0.0103 of its losses without using the transformers design and use two transformers T1 between the generator and the transmission line and T2 between the transmission line and the load.
A 30-0 resistor, a 15-02 inductive reactance, and a 12-02 capacitive reactance are connected in parallel across a 120-V 60-Hz line. Find (a) the phasor branch currents, (b) total current and phase angle, (c) impedance, and (d) power drawn by the circuit.
AC Power and Power Factor 1. Two loads are connected in parallel across a 13,200-volt line. Load A draws 200kW at 0.6 p.f. (lagging), load B takes 200kVA at 0.8 p.f. (lagging). Find the reactive, apparent and true power and the line current.
Q2) A 13.2-kV single-phase generator supplies power to a load through a transmission line. The load's impedance is Zload = 500 236.87° ohm, and the transmission line's impedance is Zline = 60 253.1° ohm. To reduce transmission line losses to 0.0103 of its losses without using the transformers design and use two transformers T1 between the generator and the transmission line and T2 between the transmission line and the load.
The one-line diagram of a three-phase power system is shown in the above figure. The line impedances are in per- unit on a 100-MVA base, and the line admittances are neglected. ' qu V = 1.05200 0.01+ j0.025 300 + j200 MVA 3 0.015 + j0.035 150 MW 200 + j150 MVA 0.01 + j0.03 |V = 1.03 The admittance matrix (Y_bus)? The bus power in per-unit?
Draw a 3-phase wye-connected generator with transmission lines connected to a 3-phase delta-connected load. Assume the lines connecting them have an inductance of j5 per phase. The generated voltages are 120 Vrms with phase 'a' having a phase angle of 0°. The loads are 10 Ohm resistors per phase. When drawing, make sure to label all 3 phases with voltage phasors, line inductances, and load resistances.
10 Ω m I₁ j4 Ω + I₂ ~ Vs E₁ || 2:1 The load on the right is absorbing 650 W -j200 VAR. V₁ = 80 / 0° V. + V₁ I
There is an installation with two equal triphasic loads of 300 kVA each and a power factor of 0.9 lagging. When connecting a pure reactive element in parallel, the reactive power at the entrance of the installation is 150 kVARS, with a lagging power factor. We can say that: a) A bank of reactors was connected and the fp deteriorated. b) A capacitor bank was connected and the pf deteriorated. c) A bank of reactors was connected and the fp improved. d) A capacitor bank was connected and the pf improved. e) None of the above
A balanced Y-connected generator with terminal voltage Vbc 5 200/08 volts is connected to a balanced-D load whose impedance is 10/408 ohms per phase. The line impedance between the source and load is 0.5/808 ohm for each phase. The generator neutral is grounded through an impedance of j5 ohms. The generator sequence impedances are given by Zg0 5 j7, Zg1 5 j15, and Zg2 5 j10 ohms. Draw the sequence networks for this system and determine the sequence components of the line currents.