A2m rigid bar is carried by three rods as shown. The mechanism is arranged such that it is symmetrical. Refer to the table for the properties of each material. Steel Bronze Allowable stress 140 MPa 120 MPa Modulus of Elasticity 200 GPa 83 GPa Area, A 400 mm2 900 mm2 Length, L 1000 mm Steel Bronze Bronze

A2m rigid bar is carried by three rods as shown. The mechanism is arranged such that it is symmetrical. Refer to the table for the properties of each material. Steel Bronze Allowable stress 140 MPa 120 MPa Modulus of Elasticity 200 GPa 83 GPa Area, A 400 mm2 900 mm2 Length, L 1000 mm Steel Bronze Bronze

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.12P

See similar textbooks

Similar questions

A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1 2 inch. The gage length (the length over which the elongation is measured) is 2 inches. For a load 13.5 kips, the elongation was 4.6610 3 inches. If the load is assumed to be within the linear elastic rang: of the material, determine the modulus of elasticity.
The rigid bar 2 m long is supported by a steel rod at the middle B and bronze rods equidistant from both ends at A and C as shown. The properties of the rods are given in the tabulation below. Steel Bronze Allowable stress 140 MPa 120 MPa Modulus of Elasticity, E 200 GPa 83 GPa Area, A 400 mm2 900 mm2 Length, L 1,000 mm What is the required length of the steel rod so the reactions on the three rods are the same? What is the required length of the steel rod so that both the steel and the bronze rods reach their allowable stresses at the same time? What is the maximum permissible load W that the rods can carry?
The light rigid bar ABCD shown is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P = 20 KN is applied. %3D Steel E200 GPa A-600mm L1 m 2.0 m 0.6 m 1.5 m Pa20 KN Aluminum E-70 GPa A=900mm L-1.5 m What is the ratio of the deformation of steel to deformation of aluminum?
Two polymer bars are connected to a rigid plate at 8, as shown. Bar (1) has a cross-sectional area of 1.42 in.and an elastic modulus of 2180 ksi. Bar (2) hasa cross-sactional area of 1139 in.and anelastic modulus of 4150 ksi. Assume l-23 in., L-41 in, Q-6.7 kips, P-3.7 kips, and R-14.1 kips. Datermine the horizontal deflection of end Crelative to end A P R (1) (2) Answer: uga in.
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m 5KN 0.6m A 20KN 3) What is the deformation &cn in mm? A=800 mm? A=1,200 mm²
SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c= 1.7m. a b I Bronze: A 1200 mm E83 GPa Lw2.0m What is the value of P Steel: A 900 mm E 200 GPa L=1.5m
The figure as shown below is a rigid bar which is supported by two rods and a pin support. If the said connections is stress- free, determine the increase or decrease of the temperature in degrees Celsius that will resulted with a tensile stress of EN mPa for the brass rod. Brass L = 2 m A = 1200 mm² E = 100 GPa a = 18.7 x 10-/°C FN=70 B - 3 m - MN=76 2 m Copper L=3 m A = 1500 mm² E = 120 GPa a = 16.8 x 10-/°C SN=50 Note: Neglect the weight of the bar and assumes that the two rods will subjected to same temperature change
As shown in the figure below, a bronze bar is affixed between a steel bar and an aluminum bar. Axial loads are applied at the positions indicated. If the largest value of P that will not exceed an overall deformation of 4.0 mm, or the following stresses: 150 MPa in the steel, 130 MPa in the bronze, and 90 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. determine the stress in the bronze, steel, and aluminum
A brass bar is fastened between a steel bar and an aluminum bar as shown in the figure. Axial loads are applied at the positions indicated. Find the largest value of P (kN) that will not exceed the maximum stresses are: 140 MPa in the steel, 120 MPa in the brass and 80 MPa in the aluminum. [Round off your final answer to 2 decimal places] Steel Brass A = 480 mm A = 650 mm? Aluminum A = 320 mm? 3P 4P 2P 1.0 m 2.0 m 1.5 m
The length of the assembly shown below decreases by 0.5 mm when an axial force is applied by means of rigid end plates. Determine (a) the magnitude of the applied force, (b) the corresponding stress in the brass core. 25 mm Brass core E = 105 GPa Aluminium shell E-70 GPa 300 mm 60 mm
3) An bronze rod is rigidly attached between a aluminum rod and a steel rod as shown. Axial loads are applied at the positions indicated. Find the maximum allowable value of P that will not exceed a stress in steel of 140MPA, in aluminum of 90MPA or in bronze of 100MPа. Aluminum A = 500mm? Bronze A = 200mm? Steel A = 150mm2 2P ЗР L st = 1.2m L br = 2m Lal = 3.5m
R14-7 The principal stresses at a point are shown in the figure. If the material is A36 steel, determine the principal strains. 84 MPa 140 MPa 6 MPa