After performing a plate and liquid lysate, it was found that the plate lysate achieved the common titre range of 1010-1011 pfu/ml whereas the liquid lysate achieved a range of 108 PFU/mL; what is the reason for the lower titre in different methodologies? How can we troubleshoot this issue in the future?

After performing a plate and liquid lysate, it was found that the plate lysate achieved the common titre range of 1010-1011 pfu/ml whereas the liquid lysate achieved a range of 108 PFU/mL; what is the reason for the lower titre in different methodologies? How can we troubleshoot this issue in the future?

Curren'S Math For Meds: Dosages & Sol

11th Edition

ISBN:9781305143531

Author:CURREN

Publisher:CURREN

Chapter10: Reconstitution Of Powdered Drugs

Section: Chapter Questions

Problem 7.2P

See similar textbooks

Similar questions

The following are errors that people commonly make when they perform serial dilutions. Indicate whether you think that the number of cfu/ ml calculated would be too high or too low if you make this mistake. You intend to add 0.9 ml of diluent to each tube and 0.1 ml of culture. Instead, you add 0.5 ml of diluent to each tube and 0.1 ml of culture to the first tube. Then, you make a serial dilution of 0.1 ml into and from each tube as described. You prepare 0.9 ml of diluents in each tube. You add 0.1 ml of culture (from the overnight culture provided) to every tube. You add 0.9 ml of diluent to each tube. You add 0.1 ml of culture to the first tube and mix. You get distracted, and transfer 0.1 ml to the third tube instead of the second. You perform the rest of the series as described.
In the spread plate method, why is the volume plated usually limited to not more than 0.1 mL?
Observe the following Plate counts and then determine the correct number of CFU/ml Plate 1 = 564 colonies at 10^-5 dilution Plate 2 = 422 colonies at 10^-6 dilution Plate 3 = 317 colonies at 10^-7 dilution Plate 4 = 93 colonies at 10^-8 dilution 93 x 10^10 CFU/ml 9.3 x 10^-9 CFU/ml 93 x 10^9 CFU/ml 93x 10^8 CFÜ/ml 93x 10^-8 CFU/ml asap please
DILUTION COLONY COUNT CFU/mL 1:106 155000 1:107 15500 1:108 1550 1:109 155 Given these values how would I fill in the rest of this serial dilution table? Also, what would be a 1:1 CFU/mL value based on this table?
6) 1 mL of supernatant is required for a procedure. The final colored solution proves to be too high to read accurately on the spectrophotometer. 100 μL of supernatant and 900 μL of distilled water are substituted for the original supernatant and the procedure, run as before. The reading from the standard curve is 46 mg/dL. What is the actual amount of substance in the patient serum?
Apple puree was analyzed for petulin by HPLC-MS-MS after SPE clean-up. The procedure was 10.0g of puree + 10μl of a 10μg/ml solution of isotopically labeled petulin as internal standard were treated with 10.0ml of pectinase and acetic acid, centrifuged, and filtered. Four ml of the filtrate was passed through a SPE cartridge. The petulin was eluted with 2.0ml of ethyl acetate. The sample was evaporated to dryness and the residue dissolved in 1.0ml of the mobile phase. The analyte signal was 127 and the internal standard 197. Calculate the concentration of petulin in the sample in μg/g (RRF=1).
How much of 10,000x SYBR safe would you add to 50 ml to make a final concentration of 1x? V1= 0.005mL B.How will you set up the serial dilution? How many tubes do you need? What is the concentration in each? How much LB will you add to each tube? What volume of cells will you add?
Paraphrase the text below: Series of test tubes were filled with the desired volume of the BSA (0.1, 0.2, 0.3… 1 ml) .PBS was added to this to make the volume of 1 mL. 5 mL of copper reagent was added to all the tubes. After proper mixing, all the tubes were incubated at room temperature for 15 minutes. 1 mL Folin reagent was added to each and mixed properly with the help of vortex mixer and incubated for 20 minutes. The intensity of the colour was then determined spectrophotometrically at 680 nm. The graph was than plotted between optical density and the amount of BSA. Proteins estimation was done for the detection for the amount of proteins present in the sample solutions by the Lowry method
You have an order for 1 gram of Cefazolin in D5W 100 ml. You have added 5 ml of sterile water to the 1 gram vial to reconstitute powder. However the recommended manufacturer’s diluent amount is 10 ml of sterile water for a final concentration of 100 mg/ml. How would reconstituting the vial with 5 mls affect the concentration and the final calculated dose. Please answer with explanation ASAP. I will really upvote. Thanks
4 mL of 10% TCA solution was added to 1 mL of serum and after mixing, it was waited for two minutes and filtered through non-phosphorus filter paper. 1 mL of the filtrate was taken and 13 mL of distilled water, 4 mL of sulfomolybdic acid and 2 mL of dilute SnCl2 solution were added and mixed, and after waiting for 15 minutes, the absorbances of the obtained solutions against pure water at 520 nm were read. If the function of the calibration graph obtained with 0.5-2.5 mg/mL standard phosphorus solutions is y= 0.245x + 0.107 and the absorbance value of the serum sample is 0.109, what is the amount of phosphorus in the sample?
You want to set up a 1:10 dilution series, so that you can plate a 10-1, 10-2, and a 10-3dilution; however, you only have access to two9 ml dilution blanks. Explain how you could accomplish this task with only two blanks.
Prepare 50 plates of Sheep's Blood Agar using 100mm petri dish. Add 10% of blood to the media. (Manufacturer's instructions: Suspend 38 g of blood agar base dehydrated powder in 1 liter of distilled or deionized water.) Pour 25 mL of prepared medium per plate. Express answer to the nearest whole number. How many grams of the dehydrated powder should be weighed? Answer: What is the volume of distilled water that should be used in the preparation? Answer: What is the volume of sheep's blood that should be added to the sterilized and cooled blood agar base? Answer: