Airstream at 1 atm flows, with a velocity of 15 m/s, in parallel over a 3-m-long flat plate where there is an unheated starting length of 1 m. The airstream has a temperature of 20°C and the heated section of the flat plate is maintained at a constant temperature of 80°C. Determine (a) the local convection heat transfer coefficient at the trailing edge and (b) the average convection heat transfer coefficient for the heated section.

Airstream at 1 atm flows, with a velocity of 15 m/s, in parallel over a 3-m-long flat plate where there is an unheated starting length of 1 m. The airstream has a temperature of 20°C and the heated section of the flat plate is maintained at a constant temperature of 80°C. Determine (a) the local convection heat transfer coefficient at the trailing edge and (b) the average convection heat transfer coefficient for the heated section.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.38P

See similar textbooks

Similar questions

5.7 The average Reynolds number for air passing in turbulent flow over a 2-m-long, flat plate is . Under these conditions, the average Nusselt number was found to be equal to 4150. Determine the average heat transfer coefficient for an oil having thermal properties similar to those in Appendix 2, Table 18, at at the same Reynolds number and flowing over the same plate.
Hot carbon dioxide exhaust gas at 1 atm is being cooled by flat plates as shown in Fig 3. The gas at 220°C flows in parallel over the upper and lower surfaces of a 2-m-long flat plate at a velocity of 2 m/s. If the flat plate srface temperature is maintained at 80°C, de termine the local convection heat transfer coefficient at 1 m from the leading edge, the average convection heat transfer rate over the e ntire plate, and the total heat flux transfer to the plate. 11. 111. COo, T. Fig 3
Water at 43.3°C flows over a large square plate at a velocity of 28 cm/s. The plate is 1.2 m long (in the flow direction) and its surface is maintained at a uniform temperature of 10.0°C. The width of the plate is 1.2 m. Calculate the steady rate of heat transfer for the entire width of the plate in watts (W). The properties of water at the film temperature of (Ts + T∞)/2 = (10 + 43.3)/2 = 27°C are ρ = 996.6 kg/m3, k = 0.610 W/m·°C, μ = 0.854 × 10–3 kg/m·s, and Pr = 5.85. The steady rate of heat transfer per unit width of the plate is ___ W.
A tube bank consists of 300 tubes at a distance of 6 cm between the centerlines of any two adjacent tubes. Air approaches the tube bank in the normal direction at 20°C and 1 atm with a mean velocity of 6.3 m/s. There are 20 rows in the flow direction with 15 tubes in each row with an average surface temperature of 140°C. For an outer tube diameter of 2 cm, determine the average heat transfer coefficient. Assume the air properties at mean temperature of 70°C and 1 atm. The air properties at the assumed mean temperature of 70°C and 1 atm are k = 0.02881 W/m·K, ρ = 1.028 kg/m3, cp = 1.007 kJ/kg·K, Pr = 0.7177, μ = 2.052 × 10−5 kg/m·s, Prs = Pr@Ts = 140°C = 0.7041. The average heat transfer coefficient of the tube bank is W/m2·°C.
Please help with this questionHot carbon dioxide exhaust gas at 1 atm is being cooled by flat plates. Thegas at 220°C flow is parallel over the upper and lower surfaces of a 3-m-longflat plate at a velocity of 3 m/s. If the flat plate surface temperature ismaintained at 80°C.Determine the local convection heat transfer coefficient at 1 m fromthe leading edge and calculate the average convection heat transfer coefficient over theentire plate.
Hot methane exhaust gas at 1 atm is being cooled by flat plates. The gas at 150°C flows parallel over the upper and lower surfaces of a 2.5 m long flat plate at a velocity of 2.5 m/s. if the flat plate surface temperature is maintained at 50°C, determine the local convection heat transfer coefficient at 1 m from the leading edge.
The upper surface of a 1 mx 1 m ASTM B152 copper plate is being cooled by air at 20°C. The air is flowing parallel over the plate surface at a velocity of 0.1 m/s. The maximum use temperature for the ASTM B152 copper plate is 260°C (ASME Code for Process Piping, ASME B31.3-2014, Table A-1M). Determine the average convection heat transfer rate from the plate surface that is required to keep the plate surface temperature from going higher than the maximum use temperature. It is given that the properties of air at the film temperature of 140°C are (Table A-15) Pr = 0.7041, k= 0.03374 W/m-K, and v= 2.745 x 10-5 m²/s. The average convection heat transfer rate is W.
Air stream at 1 atm flows with a velocity of 2 m/s, in parallel over a 3 m long square flat plate, placed on ground, where there is an unheated starting length of 1 m. The air stream has a temperature of 20 °C and the heated section of the flat plate is maintained at a constant temperature of 80 °C. Determine the local heat transfer coefficient at trailing edge and average convection heat transfer coefficient for the heated section. Also calculate the heat loss by convection. Determine the average friction coefficient and wall shear stress and drag force.
Hot carbon dioxide exhaust gas at 1 atm is being cooled by flat plates. The gas at 220°C flows in parallel over the upper and lower surfaces of a 1.5-m-long flat plate at a velocity of 3 m/s. If the flat plate surface temperature is maintained at 80°C, determine (a) the local convection heat transfer coefficient at 1 m from the leading edge, (b) the average convection heat transfer coefficient over the entire plate, and (c) the total heat flux transfer to the plate.
Hot carbon dioxide exhaust gas at 1 atm is being cooled by flat plates. The gas at 220oC flows in parallel over the upper and lower surfaces of a 1.5-m-long flat plate at a velocity of 3m/s. if the flat plate surface temperature is maintained at 80oC, determine (a) the local convection heat transfer coefficient at 1 m from the leading edge, (b) the average convection heat transfer coefficient over the entire plate, and (c) the total heat flux transfer to the plate.
8 Air at standard conditions of 1 atm and 27°C flows over a flat plate at 20 m/s. The plate is 60 cm square and is maintained at 97°C. Calculate the heat transfer from the plate.
Air at 60°F flows over a 10-ft-long flat plate at 7 ft/s. Determine the local friction and heat transfer coefficients at intervals of 1 ft, and plot the results against the distance from the leading edge.