An 8-in diameter piston is pushed inside a cylinderhaving an 8.005in diameter. The gap is filled with alubricant (v = 0.003 ft2/s, SG = 0.80 ). If the piston ismoving at 0.5 ft/s, find the frictional resistance whenthere is an engagement of 10 ft.Select the correct response:216.78lb227.98 lbO 331.12 lb324.54 lbO 236.46 Ib PartitionStop.5mWaterGasolineHingeA vertical wall separates two different fluids in anopen tank. The right side of the tank contains gasoline(SG = 0.8) at a depth of 5m. A rectangular gate hinged5m high and 3m wide is located in the wall and hingedat the bottom. Water is poured on the left side of thetank. Determine the total hydrostatic force developedby the oil and its location.Select the correct response:333.13KN, 3.87m292.67 kN, 2.32m324.1 kN, 3.79m412.01 kN, 2.50m294.3 kN, 3.33m

As per bartleby guidelines only solution of first question is given here.

An 8-in diameter piston is pushed inside a cylinder having an 8.005in diameter. The gap is filled with a lubricant (v = 0.003 ft2/s, SG = 0.80 ). If the piston is moving at 0.5 ft/s, find the frictional resistance when there is an engagement of 10 ft. Select the correct response: 216.78lb 227.98 lb 331.12 lb 324.54 lb O 236.46 Ib

An 8-in diameter piston is pushed inside a cylinder having an 8.005in diameter. The gap is filled with a lubricant (v = 0.003 ft2/s, SG = 0.80 ). If the piston is moving at 0.5 ft/s, find the frictional resistance when there is an engagement of 10 ft. Select the correct response: 216.78lb 227.98 lb 331.12 lb 324.54 lb O 236.46 Ib

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.121P: One side of the container has a 03-m square door that is hinged at its top edge. If the container is...

See similar textbooks

Similar questions

The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate and the smooth surface at B due to water pressure acting on the gate. Use =62.4lb/ft3 for water.
A circular tank with a diameter of 4.5m is filled with two immiscible fluids. Water to a depth of 3m andoil with a relative density of 0,9 to a depth of 2mDetermine the Hydrostatic force acting on the verticalside of the tank and the position of the centre of pressure from the oil-free surface.
Note: Please state what formula you are using. And please be clear and detailed with your solution. Atleast explain. It will help me, thanks. Problem: A Triangular gate having a horizontal base of 1.30 m and an altitude of 2 m is inclined 45o from the vertical with vertex pointing upward. The base of the gate is 2.70 m below the surface of oil (s = 0.80). What normal force must be applied at the vertex of the gate to open it? Show figure
what is the total hydrostatic force acting on the tainter sector gate? (in lbs)
A rectangular gate which is inclined 90-degrees with respect to the horizontal and has a 3.5 m width and 17.0 m height, is being submerged in water with its top edge is 4.4 m above the water surface. Find the induced total hydrostatic force(in kN) on one side of the gate. Answer in two decimal places. Numerical values only. Don't indicate units here, just on the submitted solution.
An open tank contains water up to a depth of 2 m and above it an oil of sp. gr. 0.9 for a depth of 1 m. Find the pressure intensity (i) at the interface of the two liquids, and (ii) at the bottom of the tank.
A CLOSED RECTANGULAR TANK 4m LONG 2m WIDE AND 2m HIG6H iS FILLED WITH WATER TO A DEPTH OF 1.8m.IF THE ALLONABLE FORCE AT THE REAR WALL OF THE TANK IS 200 KN, HON FAST IT CAN BE A CCE LERATED HORIZONTAULY?
An open tank contains 5.6m of water covered with 3.4m of kerosene (S.G=0.80). Find the pressure at the interface and at the bottom of the tank
b- The right limb of a simple U tube manometer containing mercury is open to the atmosphere while the left limb is connected to a pipe in which a fluid of specific gravity 0.9 is flowing. The center of the pipe is 12 cm below the level of mercury in the right limb. Find the pressure of fluid in the pipe if the difference of mercury level in the two limbs is 20cm. (2.5marks)
A vessel cylindrical in shape and closed at the top and bottom is 300 mm in diameter, 1 m long and contains water up to a depth of 0.8 m. The air above the water surface is at a pressure of 60 kN/m2 . If the vessel is rotated at a speed of 250 r.p.m. about its vertical axis find the pressure head at the bottom of the vessel (i) At the centre, and (ii) At the edge
A 1.5m semi-circular gate is submerged in oil having an SG of 0.95. Its base is 2m from the surface of the water. Find the location of the center of pressure from the base of the gate. Select the correct response: 0.45 m 1.70 m 1.36 m 0.30 m 0.52 m 1.53 m
Two vessel are connected to differential manometer using tubing being filled with water. The higher pressure vessel is than the other. (a) If the mercury reading is in meters of water? (b) If carbon tetrachloride (s = iwould be the manometer reading for the same pressure difference? mercury density= 13.6 Solution mercury, the connecting 1.38 m lower in elevation 110 mm, what is the pressure head difference 1.59 )were use instead of mercury, what 1.38 Air 4 water 3 m X Fig A 2 1 Air water gage liquid