Answered: An engine cylinder is 300 mm in…

An engine cylinder is 300 mm in diameter and the steam pressure is 0.7 N/mm2. If the cylinder head is held by 12 studs, find the size. Assume safe tensile stress as 28 MPa.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.4P: Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield...

See similar textbooks

Related questions

Q: Figure 5 displays a copper rod that is placed in an aluminum tube. The rod is 0.005 in. longer than…

A: Area of copper = 2 in2 Area of aluminium = 3 in2 Allowable stress of copper = 20 ksi Allowable…

Q: The state of stress at a point is given by ox = -6 MPa, ơy = 4 MPa, and Txy = -8 MPa. The maximum…

Q: As shown in the figure, a bolt with a diameter of 10 mm is affected by three separate forces in…

Q: The state of stress at a point is given by ox=-6 MPa, oy=4 MPa, and Txy=-8 MPa. The maximum tensile…

A: To find: The maximum tensile stress at the point. Given: The stress are σx=-6 MPa, σy=4 MPa and…

Q: A scuba tank is being designed for an internal pressure of 1600 psi with a factor of safety of 2.0…

Q: Q3: For figure below, find the principle stresse and their direction in points (H,K) 60 AN sO AN 15m…

Q: 1.) A long flat steel bar 6 in. wide and 3/8 in. thick has a 2.5 in. diameter circular hole…

Q: An cylinder is 30 cm in diameter and the steam pressure is 7 kg/cm. If the cylinder head is held by…

Q: Figure 5 displays a copper rod that is placed in an aluminum tube. The rod is 0.005 in. longer than…

A: E=PA∆LL⇒EA∆LL=P

Q: 2. Using maximum shear stress theory (MSS) the factor of safety for ductile material with Sy=220…

Q: (a) Calculate the tangential and longitudinal stresses in the steel. (b) To what value may the…

Q: calculate temperature change that will cause a tensile the stress of 90 MPa in the brass rod.

A: Given: Tensile stress =90 MPa To determine: The change in temperature

Q: A bracket in the form of a plate is fitted to a column by means of four rivets of the same size, as…

Q: Given: A steel rod (A= 150 mm?) is stretched between two fixed points with a tensile load of 5000 N…

Q: A cylindrical boiler with an inside diameter of 2.5 m and a wall thickness of 40 mm is made of a…

A: GIVEN DATA- Pressure P=1.5MPa Internal Dia d=2.5m = 2.5*1000=2500mm Thickness t=40mm Yield stress…

Q: Find the size of 14 bolts required for C.I.steam engine cylinder head. The diameter of the cylinder…

A: Given data: Number of bolts (n) = 14 Diameter of the cylinder (d) = 400 mm Steam pressure (p) = 0.12…

Q: A hollow aluminum cylinder made of 2014-T4 has an outside diameter of 2.50 in. and a wall thickness…

A: Given data for aluminum cylinder 2014-T4

Q: Find the tensile stress in MPa in member AB shown in the figure. All connection bars have square…

Q: Find the longitudinal stress in the tank.

A: To Find the longitudinal stress.

Q: The one end of a hollow square tube whose side is ( 10 + N/100 ) in with ( 1 + N/100 ) in thickness…

A: Data given- N= 47 So Side of sqaure x = 10+ 47/100 = 10.47 in Thickness t = 1+47/100 = 1.47 in…

Q: A hydraulic press is shown in the figure. When the press squeezes any material, P force occurs in…

A: Given data: Length of the press, l = 100 mm. Width of the press, b= 80 mm. The factor of safety, n…

Q: A proving ring is 25 cm mean diameter, 4 cm wide and 6 mm thick. The maximum stress permitted is 550…

A: A providing ring has a diameter of 25 cm, a width of 4 cm, and a thickness of 6 cm.The greatest…

Q: A 2 in diameter steel tube with a wall thickness of 0.5 inch just in a rigid hole. Find the…

A: Ans(b) stress acting in y-direction σy=PA=3140π(2)(0.05)=31400π psi Hence the stress acting in the…

Q: Q3 - The homogeneous bar AB have diameters 190mm when subjected to an axial tensile load of 34KN.…

Q: Calculate the normal stresses (in Pa) at point Bof the bracket caused by the 23010N force.

Q: A steel bar of diameter 1cm and length 10cm is made of steel E=200Gpa and yield strength of 300Mpa…

Q: ..For the figure shown blow, if the temperature decrease by 40°C. find the stress in the Aluminuim…

Q: is shown below, 400 300 200 100 Stress (MPa)

A: 1.Modulus of elasticity can be obtained by taking the slope of stress-strain curve in elstic…

Q: 1. The homogeneous bar shown in Fig. P-106 is supported by a smooth pin at C and a cable that runs…

A: Given Weight, W = 40 kN Diameter, d = 25 mm = 0.025 m Length, AB = 4 m…

Q: Find the tensile load which produce stress of 2.5 N/mm2 and cross sectional area is 2 mm2

A: Given data : Cross sectional area=A Stress=σ Required : Tensile load

Q: In the system given in the figure, the rods are identical and it is desired to be produced in the…

Q: A cylindrical pressure vessel is designed using steel plating with a thickness equivalent to 15 mm.…

A: Write the given data. t=15 mmD=460 mmH=2.5 mσL=120 MPaσc=50 MPa

Q: What would be the compressive stress in MPa developed in the silica glass furnace tube constrained…

Q: An eye bolt carries a tensile load of 20kN.Find the size of the bolt(in mm), if the tensile stress…

Q: 1. An engine cylinder is 300 mm in diameter and the steam pressure is 0.7 N/mm2. If the cylinder…

Q: 5. A cylindrical pressure vessel has an inner diameter of 240mm and a wall thickness of 1.5mm. If…

Q: Construct a Mohr circle using below information and label it appropriately. Using Iohr circle, find…

A: givennormal stress in X direction σX=150Mpanormal stress in Y diretion σY=100Mpasheer stress at XY…

Q: Find the size of 14 bolts required for a C.I. steam engine cylinder head. The diameter of the…

A: Given steam pressure=0.12N/mm2diameter of the cylinder =400 mmσ=35MPa

Q: Find the size of 14 bolts required for a CI engine cylinder head. The diameter of the cylinder is…

A: Given data as per the question Number of bolts =14 Diameter of cylinder =400 mm steam pressure =0.12…

Q: A metal tube with inside diameter of 100mm is subjected to a tensile lad of 500kN. Find the outside…

A: Inside diameterdi=100 mm di=0.1 m Outside diameter=do Tensile loadP=500…

Q: Q3. Find stresses in the Bronze and Aluminum. Find the force needed to just close the gap. 1000 KN

A: NOTE:- Here, Reder must do correctionvwhile taking area from above figure because it gives in mm^2…

Q: Ql- Compare the maximum stress induced into a rectangular plate 100mm long into x-axis direction,…

A: Given data :- Length = 100 mm Width = 50 mm Thickness = 10 mm Tensile load = 10 KN

Q: Q) In Fig.(1), the shaft is subjected to a reversed load P = (2700 to - 900) N. Find the length (L),…

Q: A closely coiled helical spring is made of 6 mm diameter steel wire, the mean diameter of the coil…

A: Given: axial load = 529 N coil mean diameter = 60 mm wire diameter = 6 mm

Q: a) A steam engine cylinder has an effective diameter of 350 mm and the maximum steam pressure acting…

A: solving the part (a)

Q: The one end of a hollow square bar whose side is 10.42 in with 1.42 in thickness is under a tensile…

Q: A wooden bar is subjected to a tensile stress of 5 mpa. What will be the values of normal stress and…

A: Given data The tensile stress σ = 5 MPa. angle between the section and the tensile stress is θ =…

Q: A cylinder head for steam engine is held by (14) bolts. The effective diameter of the cylinder is…

Q: A lead cylinder is placed into a blind hole cut into a large tungsten block, Assume it is a tight…

A: given data pressure applied at the top= 50MPa cylinder length L= 100mm dia of cylinder = 25 mm

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

An engine cylinder is 300 mm in diameter and the steam pressure is 0.7 N/mm². If the cylinder head is held by 12 studs, find the size. Assume safe tensile stress as 28 MPa.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A safety valve on the top of a tank containing steam under pressure p has a discharge hole of diameter d(see figure). The valve is designed to release the steam when the pressure reaches the value Pmax If the natural length of the spring, is L and its stiffness is k, what should be the dimension ft of the valve? (Express your result as a formula for h.)
Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
Find the size of 14 bolts required for a CI engine cylinder head. The diameter of the cylinder is 400mm and the steam pressure is 0.12N/mne.Take the permissible tensile stress as 35MPa.
Find the size of 14 bolts required for a C.I. steam engine cylinder head. The diameter of the cylinder is 400 mm and the steam pressure is 0.12 N/mm2 . Take the permissible tensile stress as 35 MPa.
An cylinder is 30 cm in diameter and the steam pressure is 7 kg/cm. If the cylinder head is held by 12 studs, find the size, assume safe tensile stress as 280 N/mm
A cylinder head for steam engine is held by (14) bolts. The effective diameter of the cylinder is (350 mm) and the steam pressure is (0.85 MPa) .find the size of the bolt if tensile stress is not to exceed (35 MPa)
. A steel boiler 2.5 m in diameter has a wall thickness of 25 mm. The internal pressure is 1.6 MPa. Calculate the factor of safety if the maximum permissible stress for it is 250 MPa?
A 12 mm thick steel tire has a width of 110 mm has an internal diameter of 800 mm. Tire is heated and shrunk to a steel wheel 800.5 mm in diameter. E=200 MPa. Find the tensile stress in the tire. Look for the compressive pressure between the tire and wheel.
(b) Determine the thickness of a plain cylinder head for 0.3m cylinder. The maximum gas pressure is approximately 3.2N/mm. Design the studs also for the cylinder cover. Assume the allowable hoop stress =42 N/mm' for cast iron; the allowable tensile stress for material of studs =63 N/mm?
For the previous problem, compute the following six stress quantities: Ox, Oy, 0z, Txy, Tyz, Tzx. Assume this is an aluminum alloy (E = 10,000 ksi, G = 3800 ksi, v = 0.33). Do not forget units!
Find the tensile load which produce stress of 2.5 N/mm2 and cross sectional area is 2 mm2
Calculate the minimum diameter for a cylindrical vessel that is to carry a gas at a pressure of 10 MPa. The thickness of the vessel is 38 mm and the hoop stress is 83 MPa and the longitudinal stress is 40 MPa. 1 Add file