An insulating wall is constructed with two layers of 250 mm thick Plywoodseparated from each other with a 16 mm thick foam. Thermal conductivity of the Plywoodand foam are 2.69 W/m.K and 0.034 W/m.K, respectively. For a temperature drop of 31.2 K, calculate the heat loss for the 5m x 4m wall. (neglect the effect of convective heat transfer between both sides of the wall.

An insulating wall is constructed with two layers of 250 mm thick Plywoodseparated from each other with a 16 mm thick foam. Thermal conductivity of the Plywoodand foam are 2.69 W/m.K and 0.034 W/m.K, respectively. For a temperature drop of 31.2 K, calculate the heat loss for the 5m x 4m wall. (neglect the effect of convective heat transfer between both sides of the wall.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.10P: 3.10 A spherical shell satellite (3-m-OD, 1.25-cm-thick stainless steel walls) re-enters the...

See similar textbooks

Similar questions

1.4 To measure thermal conductivity, two similar 1-cm-thick specimens are placed in the apparatus shown in the accompanying sketch. Electric current is supplied to the guard heater, and a wattmeter shows that the power dissipation is 10 W. Thermocouples attached to the warmer and to the cooler surfaces show temperatures of 322 and 300 K, respectively. Calculate the thermal conductivity of the material at the mean temperature in W/m K. Problem 1.4
One end of a 0.3-m-long steel rod is connected to a wall at 204C. The other end is connected to a wall that is maintained at 93C. Air is blown across the rod so that a heat transfer coefficient of 17W/m2 K is maintained over the entire surface. If the diameter of the rod is 5 cm and the temperature of the air is 38C, what is the net rate of heat loss to the air?
1.1 On a cold winter day, the outer surface of a 0.2-m-thick concrete wall of a warehouse is exposed to temperature of –5°C, while the inner surface is kept at 20°C. The thermal conductivity of the concrete is 1.2 W/m K. Determine the heat loss through the wall, which is 10-m long and 3-m high. Problem 1.1
3.10 A spherical shell satellite (3-m-OD, 1.25-cm-thick stainless steel walls) re-enters the atmosphere from outer space. If its original temperature is 38°C, the effective average temperature of the atmosphere is 1093°C, and the effective heat transfer coefficient is , estimate the temperature of the shell after reentry, assuming the time of reentry is 10 min and the interior of the shell is evacuated.
A square silicon chip 7mm7mm in size and 0.5-mm thick is mounted on a plastic substrate as shown in the sketch below. The top surface of the chip is cooled by a synthetic liquid flowing over it. Electronic circuits on the bottom of the chip generate heat at a rate of 5 W that must be transferred through the chip. Estimate the steady-state temperature difference between the front and back surfaces of the chip. The thermal conductivity of silicon is 150 W/m K. Problem 1.6
An insulating wall is constructed with two layers of 250 mm thick Plywoodseparated from each other with a 16 mm thick foam. Thermal conductivity of the Plywoodand foam are 2.69 W/m.K and 0.034 W/m.K, respectively. For a temperature drop of 31.2 K, calculate the heat loss for the 5m x 4m wall. (neglect the effect of convective heat transfer between both sides of the wall.
An insulating wall is constructed with two layers of 250 mm thick Plywood separated from each other with a 16 mm thick foam. Thermal conductivity of the Plywood and foam are 2.69 W/m.K and 0.034 W/m.K, respectively. For a temperature drop of 31.2 K, calculate the heat loss for the 5m x 4m wall. (neglect the effect of convective heat transfer between both sides of the wall.(neglect the effect of convective heat transfer between both sides of the wall)
Q1/ The fumace wall consists of 120 mm wide Reftactory bricks Air gap Insulating fire bricks -Plaster refractory brick and 120 mm wide insulating fire brick separated by an air gap. The outside wall is covered with a 12 mm thickness of plaster. The inner surface of the wall is at 1090°C and the - 1090°C room temperature is 20°C. The heat transfer coefficient from the outside wall surface to the air in the room is 18 W/m² °C, and the resistance to heat flow of the air gap is 0.16 °C /W. If the thermal conductivities of the refractory brick, insulating fire brick, and plaster are 1.6, 0.3 and 0.14 W/m. °C, respectively calculates: (i) Rate at which heat is lost per m of the wall surface; (ii) Each interface temperature. -20°C - 120 mm 120 mm12 mm
A 5cm copper plate has a thermal conductivity of 395 ?/m-k is used as a heat sink for a semiconductor. A 1mm layer of thermal paste lies in between the two and it has a thermal conductivity of 10 ? /m-k. Solve for the heat transferred at a 5cmx5cm area if the semiconductor is 80C, while the copper plate has a temperature of 30C since it is exposed to ambient air temperature.
Window height (0.8 m) and width (1.5 m) consisting of two layers of glass (k = 0.78 W/m C) thickness of each layer (4mm) and separated by an air layer thickness of (10 mm) if the coefficient of thermal conductivity of static air is (k=0.026 W/mC)Calculate the rate of heat transfer through the window. If the temperature of the inside of the window is (15 C°) and the temperature of the outer surface is (8C)
A hot water pipe is used for domestic applications is insulated with a layer of calcium silicate. If the insulation is 25 mm thick and its inner and outer surfaces are maintained at Ts,1 = 800 K and Ts,2 = 400 K, respectively. The outside diameter is 0.12 m. Calculate the heat loss per unit length of the pipe. Given the thermal conductivity of calcium silicate insulation equals to 0.09 W/m.K.
Heat transfer through composite walls The wall of a refrigerated van is of 1.5 mm steel sheet at the outer surface, 10 mm plywood at the inner surface and 2 cm of glass-wool in between. Calculate the rate of heat flow if the temperatures of the inside and outside surfaces are -15⁰C and 24⁰C. Take k(steel) = 23.2 Wm-1K-1 k(glass-wool) = 0.014 Wm-1K-1 k(plywood) = 0.052 Wm-1K-1.