Q2-A model of supersonic jet fighter is to be tested in wind tunnel for dynamic similarity. a- If the flow is considered to be isentropic, what dimensionless parameters must be the same for both prototype and model? b- Can we measure the Mach number of the jet experimentally ?How? Q3- Calculate the valosit tions

Q2-A model of supersonic jet fighter is to be tested in wind tunnel for dynamic similarity. a- If the flow is considered to be isentropic, what dimensionless parameters must be the same for both prototype and model? b- Can we measure the Mach number of the jet experimentally ?How? Q3- Calculate the valosit tions

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(b) The kinematic viscosity of a fluid used for model is one third of the kinematic viscosity of the fluid used for prototype. During testing of the model, if viscosity and gravity forces are predominant, find the scale ration, velocity ratio and discharge ration
17. The moment of viscous liquid bctween two cylinder depend on angular velocity o of internal cylinder, cylinders diameters d, D., absolute viscosity u. Find the dimensionless parameters and obtain the similarity of dimensionless parameters. M= f(d.D.
using pure water at 20°C. The velocity of the prototype in seawater (p = A 1/18 scale model of the submarine is to be tested in the water tunnel 1015 kg/m³, v = 1.4x106 m²/s) is 3 m/s. Determine: a) the speed of the water in the water tunnel for dynamic similarity D) the ratio of the drag force on the model to the drag force on the prototype
The velocity V of propagation of ripples on the surface of a shallow liquid depends on the gravitational acceleration g and the liquid depth h. If Buckingham's Theorem is used to identify the salient dimensionless group(s), how many dimensionless group(s) will be obtained? Number of dimensionless group(s) = 1. {1} (Enter your answer as a number.)
A one-tenth-scale model of a supersonic wing tested at 700 m/sin air at 20 ° C and 1 atm shows a pitching moment of 0.25kN ? m. If Reynolds number effects are negligible, what willthe pitching moment of the prototype wing be if it is flying atthe same Mach number at 8-km standard altitude?
Problem 1: Streamlining From dimensional analysis, we know the drag force is FD- CopAV2/2, where Cp is a dimensionless coefficient of drag. The two space shuttles below have the same area A, the same velocity V, and are flying through the same air. Which has a smaller Co and why? (<25 words) thine e
Q1: The drag on a 2m-diameter satellite dish due to an 80 km/hr wind is to be determined through a water tunnel test using a geometrically similar 0.25m-diameter model dish. (a) At what water speed should the model test be run? (b) With all similarity conditions satisfied, the measured drag on the model was determined to be 200 N. What is the predicted drag on the prototype dish? (c) What is the Mach number, Ma = u/a where a is the speed of sound, for the prototype air flow and the one in the water tunnel? PS: The kinematic viscosity of air is 1.56 x10-5 m²/s.-The kinematic viscosity of water is 1.0 x10- 6 m²/s. The speed of sound is 340 m/s in air and 1500 m/s in water.
State what is Bernoulli's Priciple for Pressure and Velocity? In 8 sentences only.
Question 3 The power, P, to drive an axial pump is in a function of density of fluid, p, volumetric flow rate, Q, pump head, h, diameter of rotor, D, and angular speed of rotor, N. (a) (b) (c) P PDS N3 Verify that - is a dimensionless group. Determine the remaining pi group and perform dimensional analysis. Define geometric similarity and dynamic similarity. Categorize the pi group obtained from part (b) as geometric similarity or dynamic similarity, respectively.
Q2/ A car wheel is supposed to be travelling at a speed of 80 mile per hour in the air. A scaled model (1:4) is tested in water instead of air and is supposed to have dynamic similarity. a) Determine the model speed in water b) then find the force ratio of the model to prototype if you know that: (pair = 1.22 kg/m³, µair = 1.78 x 10- 5 N.s/m?, Pwater 998 kg/m², µwater = 0.001 N.s/m²).
Viscosity of fluid plays a significant role in the analyses of many fluid dynamics problems. The viscosity of water can be determined from the correlation: H = c, where µ = viscosity (N/s · m²) T = temperature (K) C, = 2.414 × 10-5 C; = 247.8 (K) Cz = 140 (K) What is the appropriate unit for c, if the preceding equation is to be homogeneous in units?
5. The drag force, fd, on a sphere located in a pipe through which a fluid is flowing is to be determined experimentally. Assume that the drag is a function of the sphere diameter, d, the pipe diameter, D, the fluid velocity, V, and the fluid density, p. (a) What dimensionless parameters would you use for this prob- lem? (b) Some experiments using water indicate that for d = 0.2in., D = 0.5in, and V = 2ft/s, the drag is 1.5 x 10-3lb. Estimate the drag on a sphere located in a 2 - ft-diameter pipe through which water is flowing with a velocity of 6ft/s. The sphere diameter is such that geometric similarity is maintained. (Ans: 31.11b) Sphere