use angle of 92 please As a project engineer, you have been tasked to perform a stress analysis ofthe plane stresses of a stress element from the tie bar of a die castingmachine as shown in Figure Q1.60 MPa45 MPa.Figure Q1By using the stress transformation equations,a. By using the stress transformation equations, identify the state of stresswhen the element is rotated by an angle counterclockwise, where =0=92b. Identify the following stresses and sketch the appropriate stress elementsrespectively.(1)Principal stresses and principal planes.(ii)Maximum shear stress and the corresponding normal stress30 MPa By using the Mohr's circle approach,c. Construct the Mohr's circle for the stress element shown in Figure Q1.d. Identify the following stresses and sketch the appropriate stress elementsrespectively.(1)Principal stresses and principal planes.(ii)Maximum shear stress and the corresponding normal stresse. Identify the state of stress when the element is rotated by an angle of 34°counterclockwise. Sketch the stress element after rotation.

Givenσx=45MPaσy=-60MPaτ=30MPa

As a project engineer, you have been tasked to perform a stress analysis of the plane stresses of a stress element from the tie bar of a die casting machine as shown in Figure Q1. 60 MPa 30 MPa 45 MPa

As a project engineer, you have been tasked to perform a stress analysis of the plane stresses of a stress element from the tie bar of a die casting machine as shown in Figure Q1. 60 MPa 30 MPa 45 MPa

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.8P: An element in plane stress on the fuselage of an airplane (figure part a) is subjected to...

See similar textbooks

Related questions

Q: ind the position and the value of the maximum stress for the weld joint shown in the figure. Assume…

A: Given Force, F = 50 kN Length of weld, L = 60 mm Find Shear stress

Q: A new Boeing aircraft engine system has 4 turbine engines setup in parallel configuration. The…

Q: In the Figure 3, if m=15 kg, 0-30°, and static coefficient of friction = 0.25, then the maximum…

Q: What are the advantages and disadvantages of liquid propellants?

A: given; What are the advantages and disadvantages of liquid propellants?

Q: Find the value of angle 0 if the resultant is vertical. Also, find the magnitude of the resultant. Y…

Q: Positive work is defined by work done the system

A: Positive work is defined by work done...................the system

Q: Plan for the Transition to Automation (include a diagram) in Conjunction with the Appropriate…

A: The use of control systems, such as computers or robots, and information technology for…

Q: four-cylinder, 2.4-liter engine operates on a four-stroke cycle at 3200 rpm. The compression ratio…

A: Given data V=2.4 LN=3200 rpmr=18 cmS=1.06 B Here, V is the volume, N is the speed and r is the…

Q: tions 6 and 7 shown figure if the bucket weighs 70 N, determine following: 6. The tension force…

A: Please find the solution below

Q: Collar A and collar B slide on the smooth horizontal bar as shown in Figure Q3(a). Determine their…

Q: 12. The velocity of fluid is given by the following equation u(Velocity in x direction)= 2*y &…

Q: Question 3: Find the extension in mild steel wire of 10 mm in diameter and 1.6 m long, the wire is…

A: Given, Diameter of the steel wire = d = 10 mm Length of the wire = 1.6 m = 1600 mm Axial load on the…

Q: A7 To a 5ft long ½” ID pipe that is maintained at a uniform temperature of 150ºF oil enters at 70ºF…

A: Given: The diameter of the pipe, d = ½ in = 0.04166 ft The length of the pipe, L = 5 ft The…

Q: The resultant of moments of forces depends on: All the above. O The directions of the applied…

Q: The 7.5-kg rod BC connects a disk centered at A to crank CD. Knowing that the disk is made to rotate…

A: Given: m = 7.5 kg angular velocity = 18 rad/s. To find: a =? Cy = ?

Q: Questions 23, 24 and 25 For the figure shown answer the following: 23. The moment of inertia of the…

Q: A centrifugal pump that is used in pumping water to a tank operates at a rate of 1 gpm. The pump is…

A: The rate of flow of the pump is 1.29412 gpm.

Q: Explain in your own words the First Law of Thermodynamics

Q: A cantilever beam is subjected to an inclined force (P) as shown in the Figure 5, the normal force…

A: X component of given force is the normal force to the cross sectional area.

Q: (a) Due to a loading, the plate (ABCD) is deformed into the dashed shape shown in Fig. 1(a). the…

A: Given data: θ=60° Need to determine the average normal strain along the side AB and average shear…

Q: In the Figure 6, the reaction force in the y- direction at point B is (in kN): Figure 6: 5 m/ 5 m A…

A: Answer is 10 kN.

Q: Find the position and the value of the maximum stress for the weld joint shown in the figure. Assume…

A: Introduction: Welded constructions are often lower in weight than riveted structures. This is…

Q: In the Figure 3, if m=15 kg and 9=30°, then the weight component normal to the inclined surface is…

A: Mass = m = 15 Kg Weight = W = mg W = 15 X 9.81 W = 147.15 N

Q: A lifting platform is to lift a load of 15KN and is to have a system pressure of 75 bar. How be?…

Q: Q1: E-glass fibers reinforced epoxy matrix to fabricate a composite part. The volume fraction of…

A: Given:Vf=VmEf=55*Em

Q: A new Boeing aircraft engine system has 4 turbine engines setup in parallel configuration. The…

A: Please find the solution below

Q: Decide whether each of these statements is TRUE (T) or FALSE (F). For the following rung of a ladder…

A: Given: Rung of a Ladder program Two statements are given, a. Just Input 1 is activated. b. Just…

Q: In solar general evacuated tubes. off ? collectors are used for

A: Tube System for Evaporation (vac-tubes or ETS) Cargill, Mike For collecting blood, vac-tubes are…

Q: Q2: A composite material has a cross-sectional area of 1150 mm². The fibers carried a stress of 200…

Q: The velocity of A is VA=12 ft/s downward. Determine the velocity of B___________ft/s Hint:…

A: Given: vA = 12 ft/s (downwards) To find: vB = ? Assume the downward direction to be positive.

Q: Q5) The motor-pump system shown in Fig. 3 is modeled as a rigid bar of mass m = 50 kg, and mass…

A: Introduction: A spring-mass system, which is used to isolate vibrating equipment from its support…

Q: Thermodynamics problem. Saturated water occupies a volume of 1.2m3 . Heat is added until it…

Q: In the Figure 1, if Q= 40 N, P = 50 N, and B = 145°, then R is equal to (in N): Figure 1: C R A Q B…

A: R must be equal to sum of P & Q. So R equal to 90 N.

Q: Q3. (a) Collar A and collar B slide on the smooth horizontal bar as shown in Figure Q3(a). Determine…

Q: Question: Use the method of sections to determine the forces in members CD, GD, and GH. Summarize…

Q: A rigid tank contains 10kg pure water vapor at 300°C and 10 bar. The tank is now cooled down to…

Q: In the Figure 5, the normal stress on the cross- sectional area is (in Mpa): Figure 5: y P = 400 KN…

Q: The control lever is subjected to a clockwise couple of 112 N-m exerted by its shaft at A and is…

A: Given data: MA=112 N.mF=300 Na=145 mmθ=24° Need to determine the dimension (x) of the lever.

Q: 980 N, P2= 1108 N, r= Given rmine celeration of the mass center, - acceleration, and ne reaction on…

A: Given Data The mass of the cylinder is:m=258 kg The load 1 is:P1=980 N The load 2 is:P2=1108 N The…

Q: If it is desired to reduce the power required for the rolling operation of part (b), what…

A: Given : Roller operation for a workpiece To find : To reduce the power required

Q: Q4: A unidirectionally reinforced glass fiber/epoxy composite. The volume fraction of the fibers is…

A: Given: Let us consider the given data, Volume fraction for fiber=60%…

Q: The advantage of the optimized size of the piston is that it requires less material so the cost of…

A: Given Piston To find Piston geometry

Q: ircumstances necessitate recalibration and replacement of the measuring device?

A: we need to evaluate the conditions where recalibration or replacement of measuring instrument…

Q: The 200-mm-diameter gas gun is evacuated on the right of the 8-kg projectile. On the left of the…

Q: Calculate thermodynamic and isentropic efficiency of a turbine: Mass flow rate 5kg/s = Condenser…

Q: Q1: E-glass fibers reinforced epoxy matrix to fabricate a composite part. The volume fraction of…

A: Given:Vf=VmEf=55*Em

Q: In the Figure 6, the absolute force value in the bar BC is (in kN): Figure 6: 5 m X 5 m A 20 KN 5 m…

Q: Learning Goal: To become familiar with the general equations plane strain used for determining…

Q: Q2: A fiberglass composite consists of a matrix of vinyl ester and reinforcing fibers of E-glass.…

A: Disclaimer: “Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: A metal strip is to be rolled from an initial wrought thickness of 3.5 mm to a final rolled…

A: First calculate the Projected length of the deformation zone in horizontal plane and is given by…

Concept explainers

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing. 

Question

use angle of 92 please

As a project engineer, you have been tasked to perform a stress analysis of
the plane stresses of a stress element from the tie bar of a die casting
machine as shown in Figure Q1.
60 MPa
45 MPa.
Figure Q1
By using the stress transformation equations,
a. By using the stress transformation equations, identify the state of stress
when the element is rotated by an angle counterclockwise, where =
0=92
b. Identify the following stresses and sketch the appropriate stress elements
respectively.
(1)
Principal stresses and principal planes.
(ii)
Maximum shear stress and the corresponding normal stress
30 MPa

By using the Mohr's circle approach,
c. Construct the Mohr's circle for the stress element shown in Figure Q1.
d. Identify the following stresses and sketch the appropriate stress elements
respectively.
(1)
Principal stresses and principal planes.
(ii)
Maximum shear stress and the corresponding normal stress
e. Identify the state of stress when the element is rotated by an angle of 34°
counterclockwise. Sketch the stress element after rotation.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Follow-up Questions

Read through expert solutions to related follow-up questions below.

Follow-up Question

ans b please

Solution

by Bartleby Expert

SEE SOLUTION

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the following data, using Mohr's circle of stress and trigonometry, (a) Find the principle stresses and show their sense in properly oriented element and (b) find the maximum (principle) shear stresses with the associated normal stresses and show the results on a properly oriented element.
1. This question relates to stresses due to combined loading. A shaft subjected to combined torsion and axial thrust is designed to resist a shear stress and a compressive stress as shown in Figure Q1. Using the information provided in Table Q1: Figure Q1 Txy 90 mpa ox 130 mpa a) Determine the principal stresses and show them on a sketch of a properly oriented element. b) Determine the maximum shear stresses and associated normal stresses and show them on a sketch of a properly oriented element. c) Calculate the safety factors according to the three theories (Rankine, Tresca, and Von- Mises). Take the yield strength of the material as, Oyield = 250 MPa. d) Sketch the Mohr's circle for the stressed component location and indicate the stress states, principal stresses, and maximum shear stress.
Daboost/Shutterstock.com 7.2-8 An element in plane stress on the fuselage of an airplane (figure part a) is subjected to compressive stresses with a magnitude of 42 MPa in the horizon- tal direction and tensile stresses with a magnitude of 9.5 MPa in the vertical direction (see figure part b). Also, shear stresses with a magnitude of 15.5 MPa act in the directions shown. Determine the stresses acting on an element ori- ented at a clockwise angle of 40° from the horizontal. Show these stresses on a sketch of an element ori- ented at this angle. (a) PROBLEM 7.2-8 T 9.5 MPa Ţ 42 MPa 15.5 MPa 7.2-21 An element in plane stress from the frame of a racing car is oriented at a known angle (see fig- ure). On this inclined element, the normal and shear stresses have the magnitudes and directions shown in the figure. Determine the normal and shear stresses acting on an element whose sides are parallel to the xy axes, that is, determine ox, o, and 7. Show the results on a sketch of an element…
Consider the following plane stress state: Ox=30 MPa, y= -60 MPa, Txy= 30 MPa cw Calculate the following: 1. The coordinates of the center of the Mohr's circle C The location of the center of the Mohr's circle Cis ( 2. Principal normal stresses (01, 02) The principal normal stresses are σ₁ = 39.08 3. Maximum shear stress (7) The maximum shear stress is 54.08 MPa. 4. The angle from the x axis to 0₁ (p) The angle from the x axis to 0₁ (p) is -16.85 5. The angle from the x axis to 7 (s) The angle from the x axis to T (s) is 28.15 6. The radius of the Mohr's circle The radius of the Mohr's circle is 54.08. ✰ MPa. MPa and 02 = -69.08 MPa. O -15 MPa, CW CCW O MPa).
Angle 1 Tyx Tyx Figure 1 Point A- x-direction stress 60MPA(compression), y-direction stress 40MPA(tension), negative shear stress 30MPA Using your assigned point determine the following for the yz-plane: a) From basic priciples determine the stresses on the plane of the indicated angle 1-30°, Show al calculations. Draw the orientation of the stress block for this scenario. b) Repeat question (a) using a Mohr circle. c) Using a Mohr circle, determine and draw the maximum stress block of the in-plane maximum shear and principle stresses. d) Determine the stresses and orientation of the stress block where the normal stress is zero. Make use of the stress transformation equations. e) Determine the values of absolute maximum shear stress and corresponding normal stress.
The state of stress in a machine element is illustrated in the stress element as shown in Figure 4: (a) (b) 250 MPa Figure 4 By calculations ie using equations or formulae find the following: The principal stress. 400 MPa 560 MPa The normal and shear stresses on a plane inclined at 30° CW. L.
In the picture there is a sketch of a socket wrench. Assume the wrench is held at a fixed point “A”. The yield stress of the material is known to be 400 MPa. Answer the questions below Describe the stresses at point “A” and their causes and calculate the stresses. Determine the factor of safety against yield assuming the Tresca yield criteria. Determine the factor of safety against yield assuming the von Mises yield criteria using both principal stresses and “Cartesian” stresses. Do your values match or not, and is this expected? Explain. Do the calculated values make sense with the respect to the Tresca value? Explain, why or why not?
Consider the 2-D state of stress shown below. Using the provided scales graph the Mohr's Circle for the 2-D state of stress with “full" details II-Obtain the Principal Stresses, the Maximum Shear Stress, and complete the table below III- Draw the Planes of Principal and Maximum Shear Stresses in the space provided below Provide "full" details and Use 3 Sig. Fig. in this problem Oy = 15 Ksi Tcw > S y Ox =10 Ksi Тух 5 Ksi 10 5 -20 -15 -10 5 10 15 20 5 10 Tccw > S' O Avg. TMax. 01 02 Op1
A steel pipe with an outside diameter of 115 mm and an inside diameter of 105 mm supports the loadings shown. Assume a = 510 mm, b = 230 mm, P = 20 kN, P, = 16 kN, and P; = 11 kN. (a) Determine the normal and shear stresses on the top surface of the pipe at point H. (b)Determine the principal stresses and maximum in-plane shear stress magnitude at point H and show the orientation of these stresses on an appropriate sketch. a P: P H K
Problem 2: Use an eigenvalue approach to solve for the principal stresses and directions for the state of stress shown below. Show the principal stresses on a properly oriented element of material. 20 mPa
▼ Part A - State of Stress on an Inclined Plane The state of stress at a point in a member is shown on the rectangular stress element in (Figure 3), the magnitudes of the stresses are lo 100 MPa, |oy| = 35 MPa, and Try| = 49 MPa. = Using the stress-transformation equations, determine the state of stress on the inclined plane AB. Express your answers, separated by a comma, to three significant figures. ► View Available Hint(s) Or Try Submit VE ΑΣΦ ↓↑ Previous Answers vec X Incorrect; Try Again; 3 attempts remaining ? Part B - Clockwise Rotation of a Stress Element with Only One Normal Stress MPa, MPa Figure ▼ 60° 15⁰ Part A State of Stress on an Inclined Plane B 3 of 6 O 8
In the attached picture there is a sketch of a socket wrench. Assume the wrench is held at a fixed point “A”. The yield stress of the material is known to be 500 MPa. Answer the questions below Describe the stresses at point “A” and their causes and calculate the stresses. Determine the factor of safety against yield assuming the Tresca yield criteria. Determine the factor of safety against yield assuming the von Mises yield criteria using both principal stresses and “Cartesian” stresses. Do your values match or not, and is this expected? Explain. Do the calculated values make sense with the respect to the Tresca value? Explain, why or why not?