At 500°C, and in the presence of a catalyst, steam (water vapour) reacts with carbon to give a mixture of hydrogen and carbon monoxide. What is the total volume of products that would be obtained from 150 L of steam and excess carbon at 500°C and 0.95 atm? What would be the volume of products at STP?

At 500°C, and in the presence of a catalyst, steam (water vapour) reacts with carbon to give a mixture of hydrogen and carbon monoxide. What is the total volume of products that would be obtained from 150 L of steam and excess carbon at 500°C and 0.95 atm? What would be the volume of products at STP?

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter5: Gases

Section: Chapter Questions

Problem 147AE: An organic compound contains C, H, N, and O. Combustion of 0.1023 g of the compound in excess oxygen...

See similar textbooks

Similar questions

5-114 Carbon dioxide gas, saturated with water vapor, can be produced by the addition of aqueous acid to calcium carbonate based on the following balanced net ionic equation: (a) How many moles of wet CO (g), collected at 60.°C and 774 torr total pressure, are produced by the complete reaction of 10.0 g of CaCO3 with excess acid? (b) What volume does this wet CO2 occupy? (c) What volume would the CO2 occupy at 774 torr if a desiccant (a chemical drying agent) were added to remove the water? The vapor pressure of water at 60.°C is 149.4 mm Hg.
You have an equimolar mixture of the gases SO2 and O2, along with some He, in a container fitted with a piston. The density of this mixture at STP is 1.924 g/L. Assume ideal behavior and constant temperature and pressure. a. What is the mole fraction of He in the original mixture? b. The SO2 and O2 react to completion to form SO3. What is the density of the gas mixture after the reaction is complete?
93 The complete combustion of octane can be used as a model for the burning of gasoline: 2C8H18+25O216CO2+18H2O Assuming that this equation provides a reasonable model of the actual combustion process, what volume of air at 1.0 atm and 25°C must be taken into an engine to burn 1 gallon of gasoline? (The partial pressure of oxygen in air is 0.21 atm and the density of liquid octane is 0.70 g/mL.)
Hydrogen cyanide (HCN) is a poisonous gas. It can be formed by the following reaction: H+(aq)+NaCN(s)HCN(g)+Na+(aq)What volume of 6.00 M HCl is required to react with an excess of NaCN to produce enough HCN to fill a room 12119 feet at a pressure of 0.987 atm and 72F?
An organic compound contains C, H, N, and O. Combustion of 0.1023 g of the compound in excess oxygen yielded 0.2766 g CO2 and 0.0991 g H2O. A sample of 0.4831 g of the compound was analyzed for nitrogen by the Dumas method (see Exercise 129). At STP, 27.6 mL of dry N2 was obtained. In a third experiment, the density of the compound as a gas was found to be 4.02 g/L at 127C and 256 torr. What are the empirical and molecular formulas of the compound?
61 As one step in its purification, nickel metal reacts with carbon monoxide to form a compound called nickel tetracarbonyl, Ni(CO)4, which is a gas at temperature above about 316 K. A 2.000-L flask is filled with CO gas to a pressure of 748 torr at 350.0 K, and then 5.00 g of Ni is added. If the reaction describe occurs and goes to completion at constant temperature, what will the final pressure in the falsk be?
Pressures of gases in mixtures are referred to as partial pressures and are additive. 1.00 L of He gas at 0.75 atm is mixed with 2.00 L of Ne gas at 1.5 atm at a temperature of 25.0 C to make a total volume of 3.00 L of a mixture. Assuming no temperature change and that He and Ne can be approximated as ideal gases, what are a the total resulting pressure, b the partial pressures of each component, and c the mole fractions of each gas in the mix?
Titanium(III) chloride is used in the manufacture of polyethylene. It is produced by the reaction (at high temperatures) between TiCl4 gas and H2. 2TiCl4(g)+H2(g)2TiCl3(s)+2HCl(g)Assume 100% yield and constant temperature and pressure. (a) How many liters of HCI gas can be produced by mixing 3.72 L of TiCl4 and 4.50 L of H2? (b) How many liters of reactant in excess are present after the reaction is complete?
The chlorofluorocarbon CCl2F2 can be recycled into a different compound by reaction with hydrogen to produce CCl2F2(g), a compound useful in chemical manufacturing: CCl2F2(g)+4H2(g)CH2F2(g)+2HCl(g) (a) Outline the steps necessary to answer the following question: What volume of hydrogen at 225 atm and 35.5 C would be required to react with 1 ton (1.000103kg) of CCl2F2? (b) Answer the question.
What volume, in milliliters, of hydrogen gas at 1.33 atm and 33 C is produced by the reaction of 0.0223 g lithium metal with excess water? The other product is LiOH.
54 One way to generate oxygen is to heat potassium chlorate, KClO3. (The other product is potassium chloride.) If 386 mL of oxygen at 41 C and 97.8 kPa is generated by this reaction, what is the minimum mass of KClO3used?