(b) A single-phase full converter charges a battery which offers a constant value of E. A resistor R is inserted to limit the battery charging current. Derive an expression for the average charging current. Find the value of R in case of battery charging current is 6 A, supply voltage is 40 V, 50 Hz, E=12 V and voltage drop in conducting SCR is 1 V determine: (i) Power dissipated in R (ii) Supply power factor

(b) A single-phase full converter charges a battery which offers a constant value of E. A resistor R is inserted to limit the battery charging current. Derive an expression for the average charging current. Find the value of R in case of battery charging current is 6 A, supply voltage is 40 V, 50 Hz, E=12 V and voltage drop in conducting SCR is 1 V determine: (i) Power dissipated in R (ii) Supply power factor

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) IN4001 Ry OV 10k) D IN4001
1) AC power in a load can be controlled by using a. Two SCR's in parallel opposition b. Two SCR's in series c. Three SCR's in series d. Four SCR's in series 2) The advantage of using free - wheeling diode in half controlled bridge converter is that a. There is always a path for the ac current independent of the ac line b. There is always a path for the dc current independent of the ac line c. There is always a path for the dc current dependent of the ac line d. There is always a path for the ac current dependent of the ac line 3) Silicon controlled rectifier can be turned on a. By applying a gate pulse and turned off only when current becomes zero b. And turned off by applying gate pulse c. By applying a gate pulse and turned off by removing the gate pulse d. By making current non zero and turned off by making current zero
The Figure 2 shows an electronic circuit designed for supplying power to a load (R1). The supply voltage 235V (RMS, AC) at frequency of 50HZ. The required DC voltage and power for the load are 24V and 3.6 W respectively. The Electrical Components of this AC to DC converter are: A full-wave rectifier to convert AC voltage to DC voltage. A regulator with transistor and Zener diode to ensure a constant voltage and power for the load. D1 Iide 91 Vaut VLoad D2 D3 Vde VI sine R1 RL Regulate Reetifier Figure 2. Complete Circuit Assume that the diodes are real diodes (NOT ideal diodes). The following information is available: The collector to base resistor of the regulator R1 = 5.0 k The transistor Q1 with B value of 24 is used for the regulator circuit. Determine the following quantities for this electronic device and fill the table below: Question Answer The voltage of Zener Diode (Vz) The current in R1 The DC current into the regulator | (Idc) Base current of transistor (IB) Collector…
In the circuit of figure Nº A, the secondary voltage Vs is 15 volts rms with a frequency of 60 Hz, R equal to 100 Ohms and C equal to 1000 microfarads. The diodes are silicon (Vd = 0.7 volts) and the Zener diode is 15 volts. Determine:a) The magnitude of the ripple voltage at Cb) The Magnitude of the Peak Inverse Voltage (PIV) for D1 and D2..
A R-load half-wave rectifier used sinusoidal voltage source with a peak value (35.353kV). The firing angle is (30). The total resistance is 50k2 and frequency is 50HZ. Calculate (in details): load direct voltage, maximum direct voltage, normalized voltage and effective voltage, power delivered to the load, power factor, form factor, ripple factor?
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V rmsh soHz} VL-DC =20V 0.01 F 0.02 F 0.0167 F None of the above
One component that does not need to be installed in the correct orientation is a: a. Resistorb. Diodec. Voltage regulatord.
What is the value of the average voltage at the output of the circuit in the figure, knowing that: Voltage at the transformer output is equal to 5 Vac and the four diodes are from the 1N4001 family.
a) Explain the operation of the controlled full-wave bridge rectifier shown in figure 3. b) The controlled full-wave bridge rectifier shown in figure 3 has a source 120 V rms at 60 Hz, R = 1092, L=20 mH, and a = 60°. Determine: i. An expression for the load current. ii. The average load current. iii. The power absorbed by the load. iv. Sketch the graph of the output waveform. Vs S₁ S4 Figure $3 $₂ Lo Vo
3 A peak rectifier (peak tollower) Cir cuit is gian below. Vs is a GOH3 Sinuscidal Vollge with peak value Upz50V. 50V. The load resistance R= Sk . Find the Vallke of the capacitance C Such that the peak- to-peak ripple 2 volts. (idenl diede) Voltage Vr Vs
A single phase – half wave controlled rectifier with freewheeling diode is supplying a load consistingseries connected a resistor and an inductance from a 70.7V (RMS), 50Hz sinusoidal AC source.The firing delay of the thyristor is 90° and the load values are R=10Ω, L=0.1 H. Define the loadcurrent expression and draw the load current by calculating for first two periods. And calculate theaverage values of the load voltage and current.
1. The Figure (i) and Figure (ii) show the centre-tap and bridge type circuits having the same load resistance and transformer turn ratio. The primary of each is connected to 230V, 50 Hz supply. (i) Find the d.c. voltage in each case. (ii) PIV for each case for the same d.c. output. Assume the diodes to be ideal. 5:1 100 0 100 2 230 V 230 V ww ww (1) (ii)