(b) A single plate clutch has a driven plate with an annular friction lining of 380 mm outside diameter and 270 mm inside diameter. The pressure between the flywheel face and the pressure plate is 159 kN/m² and the coefficient of friction is limited to 0.28. Determine: The torque that can be transmitted by the clutch, The power transmitted at a speed of 350 rpm.

(b) A single plate clutch has a driven plate with an annular friction lining of 380 mm outside diameter and 270 mm inside diameter. The pressure between the flywheel face and the pressure plate is 159 kN/m² and the coefficient of friction is limited to 0.28. Determine: The torque that can be transmitted by the clutch, The power transmitted at a speed of 350 rpm.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.76P: The clutch described in Prob. 7.75 is to transmit a torque of 120lbft when the total spring force...

See similar textbooks

Similar questions

A A multiple disc clutch transmits 55 kW of power at 1800 r.p.m. The coefficient of friction is 0.1 and the axial intensity of pressure is not to exceed 160 kN/m. The internal radius is 80 mm and is 0.7 times the external radius. Find the number of plates needed to transmit the required torque.
A multi-disk clutch consists of two steel disks with one bronze disk. Theinner and outer diameters of the contacting surfaces are 200 and 250 mmrespectively. The coefficient of friction is 0.1 and the maximum pressurebetween the contacting surfaces is limited to 0.4 N/mm2. Assuming uniformwear theory, calculate the required force to engage the clutch and the powertransmitting capacity at 720 rpm
A multiplate disc clutch transmits 55 kilowatt of power at 1800 rpm. Coefficient of friction for the friction surface is 0.1. Axial intensity of pressure is not to exceed 160 KN/m2. The internal radius is 80mm and is 0.7 times external radius. Find the number of plates needed to transmit the required torque.
multi-disc clutch has three discs on the driving shaft and two on the driven shaft. The inner diameter of the contact surface is 120 mm. The maximum pressure between the surface is limited to 0.1 N/mm . Find the outer diameter for transmitting 25 kW at 1575 rpm . assume uniform wear condition and coefficient of friction 0.3.
The axial pressure on a single disc clutch (both sides of the disc is effective) is limited to 0.12 Mpa. This is designed for a vehicle with 13kW power at a speed of 700 rpm. Assume uniform wear conditions and a friction coefficient of 0.25. If the outer dimater of the disc is 1.25 times the internal diameter, determine the dimensions of the disc lining and the axial force exerted by the springs.
Determine the axial force required to engage a cone clutch transmitting 25 kW power at 750 rpm. Average friction diameter of the cone is 400 mm, semicone angle 10°and coefficient of friction 0.25.
A multiplate disc clutch has 6 active friction surfaces. power transmitted is 20 kW at 400 rpm. Inner and outer radii of the friction surfaces are 90 mm and 120 mm respectively. Assuming uniform wear, with a coefficient of friction 0.3. Find the maximum axial intensity of pressure between the discs.
A multi-plate clutch must transmit 23 kW of power without slipping at 2500 rev/min. The coefficient of friction is 0.35. The inner and outer radius are 80 and 160 mm respectively. The axial force applied to the plates is 730 N. Determine the number of plates required using uniform wear theory. (3) A compressor degree
A multiple-disk clutch with 17 disks, 8 disks turning with one shaft and 9 with the other shaft, is rated at 25 hp at 500 rpm. The outside and inside diameters of the disks are 5½ and 2½ in., respectively. The coefficient of friction is 0.2. (a) Determine the axial force required to transmit the rated torque and determine the pressure between the disks.
A multiple disc clutch has three discs on the driving shaft and two on the driven shaft, providing four pairs of contact surfaces. The outer diameter of the contact surfaces is 250 mm and the inner diameter is 150 mm. Determine the maximum axial intensity of pressure between the discs for transmitting 18.75 kW at 500 r.p.m. Assume uniform wear and coefficient of friction as 0.3.
A multiplate clutch has three pairs of contact surfaces. The outer and inner radii of the contact surfaces are 100 mm and 50 mm respectively. The maximum axial spring force is limited to 1 kN. If the coefficient of friction is 0.35 and assuming uniform wear, find the power transmitted by the clutch at 1500 r.p.m.
Q2) A multi-plate clutch as in the figure below transmits power at 1500 rpm. The coefficient of friction is 0.4 the inner and outer diameters are 30 and 150 mm respectively. The axial force applied to the plate is 400N. Calculate the torque and power that can be transmitted without slipping using the uniform pressure theory, (03)