(b)The kinematic viscosity of a fluid used for model is one third of the kinematic viscosityof the fluid used for prototype. During testing of the model, if viscosity and gravity forces arepredominant, find the scale ration, velocity ratio and discharge ration

Given: The kinematic viscosity of the model is 1/3 of the kinematic viscosity of the prototype.…

Answered: (b) The kinematic viscosity of a fluid…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

17. The moment of viscous liquid bctween two cylinder depend on angular velocity o of internal cylinder, cylinders diameters d, D., absolute viscosity u. Find the dimensionless parameters and obtain the similarity of dimensionless parameters. M= f(d.D.
The kinematic viscosity of liquid oil (10³) C.S (1 stoke =100 C.S) and relative density = 0.92. Find the viscosity of the fluid oil in c.g.s and SI %3D systems.
2. Some common variables in fluid mechanics include: volume flow rate Q, acceleration of gravity 9, viscosity μ, density p and length, 1. Which of the following combinations of these variables are dimension- less? a., b., c. 2, d. p. μ
Q2-A model of supersonic jet fighter is to be tested in wind tunnel for dynamic similarity. any equations a- If the flow is considered to be isentropic, what dimensionless parameters must be the same for both prototype and model? b- Can we measure the Mach number of the jet experimentally ?How? Q3- Calculate the velocity of the sound at (27 C) in the following medias:- a- Air b- Water c- Steel
7. Aflat thin plate is dragged at a constant velocity of 4 m/s on the top of a 5 mm deep liquid layer of viscosity 20 centipoise. If the area of the plate is 1 m² find the drag force. Assume variation of velocity in the liquid to be linear. [Ans. 16 N]
For studying of a dam in the laboratory, a model overflow has been built in the scale of , to 36 Prototype. The flowrate of the flow in the model is 0.15 . The required time for moving of water between two points in the model is 1 minute. Calculate: i. The volume flowrate in the prototype. ii. The required time for moving of water between the points in the prototype.
1. In Buckingham π theorem, if n is the number of variables and m is the number of basic dimensions, the number of independent dimensionless parameters would be,A. (m – n) B. (n – m) C. (m + n) D. (n/m)
Ex. The force required to tow a 1:30scale model of a motor boat in a lake at a speed of 2m/s is 0.5 N, Assuming that the viscosity resistance due to water and air is negligible in comparison with the wave resistance, calculate the corresponding speed of the prototype for dynamically similar conditions. What would be the force required to propel the prptype at that velocity in the same lake? Ans.: 10.95m/s, 13500N
Fluid Dynamics (Similtude) If the fluid oscillates at a frequency of 10 rad/s in a 100 mm diameter pipe, what will be thefrequency of oscillation in a ¼ scale model, assuming the same fluid is used in the model andthe full size pipe.
Q1: Apply appropriate solution method using math principles to prove that "the pressure at a point in a fluid has the same magnitude in all directions". Support your answer with sketch. Answer: Px Pz = Pn P are the mean pressures at the three surfaces in the x- and z-directions. Q2: Formulate the issue and identify key variables to prove that [AP = P2 - P, = pg Az = y, Az], where y, and p are the specific weight and density of the fluid, respectively. Az is the vertical distance. Support your answer with sketch. Q3: From fluid mechanics science perspective, define the center of gravity and the center of pressure. Q4: Identify the hydrostatic force acting on the top surface of a submerged rectangular plate by applying principles of engineering for the following cases: 1 tilted plate, (2 vertical plate, and 3 horizontal plate. Support your answer with sketch. Q5: By applying principles of fluid mechanics science, define the "rigid-body" and identify its features. Q6: Formulate the issue…
Taylor number (Ta) is used here to describe the ratio between the inertia effect andthe viscous effect. By applying Buckingham Pi’s Theorem, determine an equation forTa as a function of the radius of inner cylinder (r), cylinder tangential velocity (v),fluid dynamic viscosity (μ), gap distance (L) and fluid density (ρ).
An incompressible fluid oscillates harmonically (V = Vosinut, where Vis the velocity) with a frequency of 9 rad/s in a 6-in.-diameter pipe. A 1/5 scale model is to be used to determine the pressure difference per unit length, Ap, (at any instant) along the pipe. Assume that Api= f(D, Vo, w, t, u, p) where D is the pipe diameter, w the frequency, t the time, the u fluid viscosity, and p the fluid density. If the same fluid is used in the model and the prototype, at what frequency should the model operate? Wm i rad/s

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

(b) The kinematic viscosity of a fluid used for model is one third of the kinematic viscosity of the fluid used for prototype. During testing of the model, if viscosity and gravity forces are predominant, find the scale ration, velocity ratio and discharge ration