C2(i)Assume that annual energy requirement of an industry is 20900 kWh ,we calculate that what will be the size of wind turbine that is required to be installed to meet the energy requirement. Following assumptions are taken into account for estimation: Annual energy requirement = 20900 kWh Propeller type wind machine is used Coefficient of performance = 0.40, Loss factor value = 0.325 Wind speed at 6 meter/sec (This wind speed should be taken from the wind data prepared for that location.) Density of air = 1 kg/m Capacity factor = 0.30 (i.e. 30% of the time, wind machine is producing energy at rated power) Number of hours in a month 730 hours.

C2(i)Assume that annual energy requirement of an industry is 20900 kWh ,we calculate that what will be the size of wind turbine that is required to be installed to meet the energy requirement. Following assumptions are taken into account for estimation: Annual energy requirement = 20900 kWh Propeller type wind machine is used Coefficient of performance = 0.40, Loss factor value = 0.325 Wind speed at 6 meter/sec (This wind speed should be taken from the wind data prepared for that location.) Density of air = 1 kg/m Capacity factor = 0.30 (i.e. 30% of the time, wind machine is producing energy at rated power) Number of hours in a month 730 hours.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Prototype of a mixed flow mini heart support pump at n1= 11000 rpmthe manometric pressure height is 100 mmHg, the flow rate of the blood-like liquid it pumps is 5.5 l/min and the efficiency is 9%. The relative density of this liquid is 1.06. It can be assumed that yields have not changed.a) find the power of the pump at this speed (n1).b) if the speed of this pump is reduced to n2 = 8000 rpm, what is the flow rate, manometric pressure height and power?
In a wind farm the following information is given: Average wind speed = 8 m/s, Rotor diameter = 80 m Coefficient of performance= C,= 0.45, Air Density p = 1.25 Kg/m³ Compute the number of wind turbines in order to produce the equivalent energy of a 600 MW CCGT operating at 80% of the load factor. In example 1, if the regular spacing of turbines is 5 times the rotor diameter, and for a gas generator, tonnes of CO2 / GWh of electrical output is 405, calculate: (i) The number of turbines per Km². (ii) The total ground area required in Km?. (ii) The Per day CO2 emission saved in tonnes.
Q1/ A) An impulse wheel is to be designed to develop at the nozzle pressure is 40 kg/cm and the deflect the jet impinging on them 150°. The center line of the bucket is on a circle of 250 cm find:- 1. The speed of the Pelton wheel (rpm). 2. Efficiency and hours power the theoretical, at the nozzle flow rate 3 m/sec. 3. Specific speed. B) What importance has the ratio? M = (mean diameter of Pelton wheel)/ (least diameter of jet) in designing the Pelton turbine.
Assume that annual energy requirement of an industry is 20000 kWh . DETERMINE size of wind turbine that is required to be installed to meet the energy requirement . Following assumptions are taken into account for estimation Annual energy requirement - 20000 kWh Propeller type wind machine is used . Coefficient of performance -0.40 Wind speed at 15 meter height is 5 meter / sec ( if the turbine hub is placed at the height other than 15 meter , the wind speed should be estimated as shown in " vertical wind speed variation section Density of air - 1 kg / m Capacity factor -0.30
Air pressure pand temperature Tat the inlet of reciprocating compressor are 1 bar and 15 °C. The outlet pressure is 8 bar.The power of the compressor Pis 551.6 W and the volume flow rate of inlet air qy is 122 litres/minute. The rotational speed of the compressor Nis 2850 rpm and the volumetric efficiency ny is 74.0%. Each question is worth of Calculate: a) Suction volume Vsuction b) Displacement volume Vstroke c) Isothermal power Pr cm³ (with one decimal accuracy) d) Isothermal efficiency T cm3 (with one decimal accuracy) W (with zero decimal accuracy) Your last answer was interpreted as follows: % (with zero decimal accuracy) Your last answer was interpreted as follows. Calculate the time t it takes to produce 20 litres of compressed air
Consider a geographical location where a wind turbine is to be installed with the following data: Wind velocity V, = 40km/hr (11.11 m/s); Atmosphere pressure 101.3kPa, the wind temperature is 20°C, Blade diameter (Rotor swept diameter D = 10m). Determine the following: a) What is the maximum available power, P, available b) What can be the maximum extracted power P, extract c) What is the rotor speed w and torque t.
Given: Rotor dia. = 4m; Power coefficient, Cp = 0.35; Ave. wind speed = 6 m/s; Air density = 0.124 kgs^2/m^4; Generator efficiency = 90%. Solve for the 1) Swept Area, 2) Density of Air in kg/m^3, 3) Output power of the windmill, and 4) Available power of the windmill.
Q1/ A) An impulse wheel is to be designed to develop at the nozzle pressure is 40 kg/cm and the deflect the jet impinging on them 150°. The center line of the bucket is on a circle of 250 cm find:- 1. The speed of the Pelton wheel (rpm). 2. Efficiency and hours power the theoretical, at the nozzle flow rate 3 m'/sec. 3. Specific speed.
Solve the ff. The discharge pressure of an air compressor is 5 times the suction pressure. If the volume flow at suction is 0.7m3/s and discharge volume flow of 0.2217m3/s, what is the compressor power(hp) if suction pressure is 100kpa. Ans. 191.72 A double acting air compressor has a cylinder dimension of 50cm x 60cm, 750rpm will have a volume displacement (m3/s) of: Ans. 2.945 A pump has a specific speed of 45 and 600rpm when it delivers 0.01m3/s. Find the head developed by the pump in ft. Ans. 926.07
Find the air horsepower of an industrial fan that delivers 28m³/s of air through a 949 mm by 1110 mm outlet. Štatic pressure is 227mm of water gauge and air density is .18 kg/m³.
2- Diesel engine, six cylinders is tested at 4750 rpm, the pressure and temperature of the air entering the engine are 1.2bar, and 25 if the bore of cylinder is 80 mm and stroke 120 mm ,take air fuel ratio is 12:1, the specific fuel consumption is 0.52kg/kWh, and the brake power is equal 94 kW find the following: fuel consumption m'f = kg/ sec the air consumption engine capacity.: the flow rate of air intake to cylinder the Volumetric efficiency
What is the crossover point in miles between thehybrid vehicle in Problem S5.4 and this alternative vehicle from acompeting auto manufacturer?