Consider the following circuit. When oscillation is stable, the internal drain-sourceresistance of the JFET is 350 2. Therefore, the setting of Rf is:((9₁0.015 F-R₁1.0 ΚΑΙR₂10kn2.46 ΚΩΩ22700Ο1.64 ΚΩΟ 2.34 ΚΩR₂ΣτόκαQ₁2N5458C₂0.015 FกR₂820 12R₂10 kn=-0%-D₁=IN914C₂10μF

Answered: Image /qna-images/answer/70a82226-bf9d-49bb-8cef-6ce834843c8a.jpg

Consider the following circuit. When oscillation is stable, the internal drain-source resistance of the JFET is 350 02. Therefore, the setting of R, is: www R₂ 1.0 km = C₂₁ 0.015 F R₁ ||₁ = 2.46 ΚΩ 700 Ω LC₁₂ 0.015 μF Q 2N5458 1.64 ΚΩ | 2.34 ΚΩ www R₂ R₂ 820 12 ww R₂ 10 k -ov D₁ IN914 C₂ 10μF

Consider the following circuit. When oscillation is stable, the internal drain-source resistance of the JFET is 350 02. Therefore, the setting of R, is: www R₂ 1.0 km = C₂₁ 0.015 F R₁ ||₁ = 2.46 ΚΩ 700 Ω LC₁₂ 0.015 μF Q 2N5458 1.64 ΚΩ | 2.34 ΚΩ www R₂ R₂ 820 12 ww R₂ 10 k -ov D₁ IN914 C₂ 10μF

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

D1 D V1 D4 D2 V D D Diode Model: 1N5817 R = 10k Vi= sine (0 5 100) Given the parameters above, simulate the given circuit using .tran 0 30m 0. Solve for the output peak to peak voltage across the resistor and the output frequency measured across the resistor. Output Frequency = (When computing for the frequency, use 4v as reference point) Output Voltage (pk-pk) = + R1 R D3 D
2- For the circuit given below : Vin is a sine wave Vinpp=9 V and Vref=2.4 V , Assume Vsat=±12V Name the circuit and draw the input and output waveforms . Vo Vin Vref +
A boost regulator has L=0.15 mH and C=0.11 mF with a duty cycle of 0.66 at a switching frequency of 50 kHz. The average load current is la=0.5A. The maximum ripple output voltage is: Select one: a. None of these b. 1.6V C. 2.6V d. 0.6V
4. An RC filter stage (R = 33 02, C = 120 µF) is used to filter a signal of 24 V dc with 2 V rms operating from a full wave rectifier. Calculate the percentage ripple at the output of the RC Section for a 100-mA load. Also calculate the ripple of the filtered signal applied to the RC stage.
From the circuit below, determine the output peak voltage Vm ? Np:Ns 6:1 Vp 120 Vac out 60 Hz DA R = 200 2 O Ovpeak O 169.71Vpeak O 28.28Vpeak O 1018.23Vpeak
For the following zener clipper draw the output waveform Vz1 = 5V, Vz1 = 7V VK = 0.8v lkn ISV V₁₂ 5V 2, 72. -5V Q2 Determine The Output Waveform And Calculate The current and PIV 1kQ 1kQ 10 V 10 si www www Q. For the circuit shown in Figure below (1),find the maximum and minimum values of zener diod current. Live 5 ΚΩ www I IL 15 80-120 V 10 ΚΩ LIR 101 102 1015 S Ne 1 k0 www Iz 50 V U2 -ot V. Fumal inash
8. The circuit shown below is a small sine wave signal with average zero andtransistor ß =98Find the value of R(E) to establish a dc emitter current of about 0.8 mA
lp ET v aph S Normal No Spacing Heading 1 Heading 2 Styles Ti The nominal output voltage of a certain regulator is 8 V. The output changes by 2 mV when the input voltage rises from 12v to 18V. Complete the following: a. Determine the line regulation and express it as a percentage change. b. Express the line regulation in %/V.
A 60 Hz sinusoidal voltage is applied to an SCR full-wave rectifier. If the DC output voltage is 74 V and the firing angle of the SCR is 60 degrees, the RMS voltage at the input would be: O A. 220 V O B.99 V O C. None of the other choices are correct OD. 110 V O E.256 V
Using two astable M.V timer .Desine the wave form shown in the figure below with Vcc=9v, C= 1.6234.Mf . then 1-Determine the duty cycle and the frequency at the output of each M.V timer 2- Draw Vc and Vo at each cct. output o/P 9.1 25 27 29.1 38.2 50 52 58.2 ms
3. Determine Veand Sketch output waveform for the clamper network shown. 20 V Si C Vi R 4 V- | -20 V 4. An RC filter stage (R = 42 0, C = 220 µF) is used to filter a signal of 30 V dc with 6 V rms operating from a full wave rectifier. Calculate the percentage ripple at the output of the RC Section for a 200-mA load. Also calculate the ripple of the filtered signal applied to the RC stage.
Repeat example 35 for FWD and firing angle Fa) 60°. 215 l65 D1985 Example 35: A full wave rectifier used 220V, with firing angle 10° ,total resistance load 5 KQ, inductance 2.34 H,and frequency 60HZ, Draw and calculate: (a) VD.c and Ipc (b) VD.C(Max) (c) Vn (d) Vorms-