10:09ll 4G 4A moodle.nct.edu.ompicture of it and attach it inside the word file.a) High Voltages are preferred for Transmission ofElectricity. Why?b) Why Generation Voltage Levels are low in therange of 11 kV/ 33 kV etc?c) Why ACSR Conductors are preferred overCopper Conductors?d) Overhead Transmission Lines are preferred forTransmission of Power for Long Distances, why?e) Alternating Current is preferred over DirectCurrent in Power System, Why?f) Write the Installed Generation Capacity ofSultanate of Oman with current energy shareof Conventional and Non-Conventional EnergySources.g) Why the Capacitance effect is neglected inShort Transmission Line.h) Distinguish between Lumped or Distributedelements in a Transmission Line.Save the assignment file using the student ID& Course code [ Eg : 22s1234 – EEPW2252]The answer document should be uploaded inthe TURNITIN LINK and if any problem occurs,send it to the staff emailSubmit through Turnitin link provided belowhttps://moodle.nct.edu.om/mod/turnitintooltwo/view.płid=21804

cture of it and attach it inside the word file. High Voltages are preferred for Transmission of =ctricity. Why? Why Generation Voltage Levels are low in the nge of 11 kV/ 33 kV etc? Why ACSR Conductors are preferred over pper Conductors? Overhead Transmission Lines are preferred for ansmission of Power for Long Distances, why? Alternating Current is preferred over Direct rrent in Power System, Why? Write the Installed Generation Capacity of Itanate of Oman with current energy share Conventional and Non- Conventional Eneray

cture of it and attach it inside the word file. High Voltages are preferred for Transmission of =ctricity. Why? Why Generation Voltage Levels are low in the nge of 11 kV/ 33 kV etc? Why ACSR Conductors are preferred over pper Conductors? Overhead Transmission Lines are preferred for ansmission of Power for Long Distances, why? Alternating Current is preferred over Direct rrent in Power System, Why? Write the Installed Generation Capacity of Itanate of Oman with current energy share Conventional and Non- Conventional Eneray

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.1P: The Aluminum Electrical Conductor Handbook lists a dc resistance of 0.01558 ohm per 1000 ft at 20C...

See similar textbooks

Similar questions

In a string of suspension insulator with three units, the line unit has 20kV and k=0.35. The voltage across tower unit is........ and across middle unit is.......
High Voltage level in Transmission system ensures ………………… a. High current in Overhead conductors b. Less power factor c. Low Power Transfer d. Reduction in conductor size
Alumoweld is an aluminum-clad steel conductor. a. True b. False
In an outdoor substation the three bus-bar conductors are supported by units of post type insulators. Each unit consists of a stack of 3 pin type insulators fixed one on the top of the other. The voltage across the lowest insulator is 15kV and that across the next unit is 12kV. Estimate: i. ratio of mutual to self-capacitance ii. the bus-bar voltage of the substation. iii. Efficiency across the string of insulators
a.Why does power plants have high amounts of voltages? Explain. b.Is it safe for transmission lines to have high current instead of high voltage? Why? c.What phenomenon is avoided by having separations between three conductor phases? Explain this phenomenon.
Subject: Electrical & Electronics Engineering Course: Power Systems Question: What is GMR and GMD? Explain your answer in case of a composite conductor.
An over head transmission line supported from two towers location at the same level. The distance between the towers is 200 m. The tension in the wires is 9000 N. The weight of one meter of the conductor is 10 N. The sag of the wires is * 2.55 m 1.55 m 4.55 m 5.55 m Non of them
Discuss the desirable properties of insulators. Explain the causes of insulator failure due to electrical breakdown. Each line of a three-phase system is suspended by a string of three identical insulators of self-capacitance C farad. The shunt capacitance of connecting metal work of each insulator to earth is 20.7 % of C while for line it is 13.8 % of C. Calculate the string efficiency of the system if a guard ring increases the capacitance to the line of metal work of the lowest insulator to 0.25 C.
An overhead line has span of 260m. The tension in the line is 1200kg while the conductor weighs 650 kg per 100 meters. Calculate the maximum SAG in the conductor. If the height of the tower is 13 meters, estimate the clearance of conductor to the ground. Draw a figure and mark values of sag, clearance, span, height of conductor etc.
Question 1) A 154 kV transmission line has a length of 100 km. The line and the conductors are given in Figure 1. The line is operated at f= 50 Hz. For both old and new lines calculate; a. GMD and GMR. b. Inductance of the line in Henries (H). c. Series Impedance (Z) of the line in Ohms. d. *Compare the results for both lines and comment on the results. e. *If the distance between the two neighbouring conductors is increase from 13 meters to 15 meters what would be the parameters in part a.,b. and c. comment on the results. New Line's Conductors 13 m 13 m Old Line's Conductors d r = 2 cm d = 40 cm r = 2 cm Figure 1
What is a FACTS (Flexible Alternating Current Transmission System) device, and how does it impact power system operation?
Single core cable design for 25 kV. The radius of conductor is 0.5 cm. The insulation material consists of two layers. The thickness of each layer is 2 cm. The voltage of first and second layers are 20 kV, 5 kV respectively. The minimum Electric stress of the cable is *