Exercises 4 1. A 30 mm diameter mild steel bar is being turned at a spindle speed of 8 rev/s, on a multi-tool centre lathe having eight tools in operation. The feed is 0-3 mm/rev, the specific cutting pressure/tool is 2 000N/mm and the total power consumed for the operation is 14 kW. If the depth of cut is to be kept the same for each tool, calculate the depth of cut/tool in mm.

Exercises 4 1. A 30 mm diameter mild steel bar is being turned at a spindle speed of 8 rev/s, on a multi-tool centre lathe having eight tools in operation. The feed is 0-3 mm/rev, the specific cutting pressure/tool is 2 000N/mm and the total power consumed for the operation is 14 kW. If the depth of cut is to be kept the same for each tool, calculate the depth of cut/tool in mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Exercises 4 1. A 30 mm diameter mild steel bar is being turned at a spindle speed of 8 rev/s, on a multi-tool centre lathe having eight tools in operation. The feed is 0-3 mm/rev, the specific cutting pressure/tool is 2 000N/mm2 and the total power consumed for the operation is 14 kW. If the depth of cut is to be kept the same for each tool, calculate the depth of cut/tool in mm. (Ans. 3-8 mm)
A shaper is operated at 120 cutting strokes per minute and is used to machine a work piece of 250 mm in length and 120 mm wide. Use a feed of 0.6 mm per stroke and a depth of cut of 6 mm. Calculate the total machining time to for machining the component. If the forward stroke is completed in 230°, calculate the percentage of the time when the tool is not contacting the work piece.
For the operation of straight turning in a lathe machine, the diameter of the workpiece is 80 mm, the length is 0.12 m, the cutting speed is 80 m / min, the feed is 0.5 mm / rev and the depth of cut is 0.002 m . Find the material removing rate and the time of machining.
A mild steel specimen of Initial diameter of 53.5 mm is turned to final diameter of 47 mm for an initial length of 154 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii) During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Total time required to complete the turning operation is 59.6 minutes
A mild steel specimen of Initial diameter of 53.5 mm is turned to final diameter of 47 mm for an initial length of 154 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii) During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Total time required to complete the turning operation is 59.6 minutes (a) Find number of passes to finish the entire turning operation ( (b) The actual length of the turning operation in mm ('
A mild steel specimen of Initial diameter of 32.5 mm is turned to final diameter of 25 mm for an initial length of 154 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.3 mm/rev & Depth of cut is 0.5 mm (ii)During machining the tool's approach length is 6 mm, over run length is 3mm (iii) Time required to complete one single turning operation is 2.3 minutes (a)Find number of passes to finish the entire turning operation (b) Total time required to complete the turning operation in minutes (c) Spindle speed in in rpm (d) Cutting speed in m/minutes
The face milling cutter of D = 200 mm used to cut a block which is 200 mm H, 1=480 mm, if f- 0.7 mm/rev is used and the overrun of the cutter is 12 mm and cutting speed 320 mm/min. Calculate the machining time. Cuttin
A mild steel specimen of Initial diameter of 30.5 mm is turned to final diameter of 27 mm for an initial length of 153 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii)During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Time required to complete one single turning operation is 3.5 minutes (a)Find number of passes to finish the entire turning operation (b) Total time required to complete the turning operation in minutes
A mild steel specimen of Initial diameter of 30.5 mm is turned to final diameter of 27 mm for an initial length of 153 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii)During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Time required to complete one single turning operation is 3.5 minutes (c) Spindle speed in in rpm (= (d) Cutting speed in m/minutes(=
A mild steel specimen of Initial diameter of 53.5 mm is turned to final diameter of 49 mm for an initial length of 151 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.2 mm/rev & Depth of cut is 0.5 mm (ii) During machining the tool's approach length is 7 mm, over run length is 4mm (iii) Total time required to complete the turning operation is 52.6 minutes (a) Find number of passes to finish the entire turning operation (b) The actual length of the turning operation in mm (c)The time required to complete one single turning operation in minutes (d) Spindle speed in rpm
What is the cutting speed of turning in the unit of m/min, when main axis spindle speed is 2,409 rpm and external diameter is 86mm ? Answer in 2 decimal points. Calculate the theoretical spindle rotational speed in rpm required to drill a 1 mm hole in copper using high speed steel drill. The recommende cutting speed is as following. The thickness of the copper plate is 24. (Leave the answer in numerical value, no need to key in 'rpm') Typical cutting speeds (m/min) High speed steel Material Tungsten carbide Aluminum 100 500 60 330 Copper Hard brass 45 230 Bronze 35 180 Mild steel 28 250 Cast iron 20 160
45) Find the RPM for turning a 1 1/4 inch shaft on a lathe with the material having a cutting speed of 150 ft/min.