Plate 200 mm x 90 mm is to be maintained on a shaper under following condition, v= 13.5 m/ min Feed is 0.57 mm/ double stroke, Approach and overtravel 20 mm each in longitudinal direction and 4 mm each in lateral direction. The ratio of cutting to the return speed is 0.83.Calculate the machining time in minutes?

Plate 200 mm x 90 mm is to be maintained on a shaper under following condition, v= 13.5 m/ min Feed is 0.57 mm/ double stroke, Approach and overtravel 20 mm each in longitudinal direction and 4 mm each in lateral direction. The ratio of cutting to the return speed is 0.83.Calculate the machining time in minutes?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A mild steel specimen of Initial diameter of 53.5 mm is turned to final diameter of 47 mm for an initial length of 154 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii) During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Total time required to complete the turning operation is 59.6 minutes
A mild steel specimen of Initial diameter of 53.5 mm is turned to final diameter of 47 mm for an initial length of 154 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii) During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Total time required to complete the turning operation is 59.6 minutes (a) Find number of passes to finish the entire turning operation ( (b) The actual length of the turning operation in mm ('
A mild steel specimen of Initial diameter of 53.5 mm is turned to final diameter of 49 mm for an initial length of 151 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.2 mm/rev & Depth of cut is 0.5 mm (ii) During machining the tool's approach length is 7 mm, over run length is 4mm (iii) Total time required to complete the turning operation is 52.6 minutes (a) Find number of passes to finish the entire turning operation (b) The actual length of the turning operation in mm (c)The time required to complete one single turning operation in minutes (d) Spindle speed in rpm
The end of a large tubular workpart is to be faced on a NC vertical boring mill. The part has an outside diameter of 38.0 in and an inside diameter of 24.0 in. If the facing operation is performed at a rotational speed of 40.0 rev/min, feed of 0.015 in/rev, and depth of cut of 0.180 in, determine (a) the cutting time to complete the facing operation and the cutting speeds and metal removal rates at the beginning and end of the cut.
A mild steel specimen of Initial diameter of 30.5 mm is turned to final diameter of 27 mm for an initial length of 153 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii)During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Time required to complete one single turning operation is 3.5 minutes (a)Find number of passes to finish the entire turning operation (b) Total time required to complete the turning operation in minutes
A mild steel specimen of Initial diameter of 30.5 mm is turned to final diameter of 27 mm for an initial length of 153 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii)During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Time required to complete one single turning operation is 3.5 minutes (c) Spindle speed in in rpm (= (d) Cutting speed in m/minutes(=
A mild steel specimen of Initial diameter of 32.5 mm is turned to final diameter of 25 mm for an initial length of 154 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.3 mm/rev & Depth of cut is 0.5 mm (ii)During machining the tool's approach length is 6 mm, over run length is 3mm (iii) Time required to complete one single turning operation is 2.3 minutes (a)Find number of passes to finish the entire turning operation (b) Total time required to complete the turning operation in minutes (c) Spindle speed in in rpm (d) Cutting speed in m/minutes
A surface of 43 mm x 246 mm will be machined by using a shaper and 7 mm deep stock will be removed from the surface. The shaper is operating at 24 strokes/minute and feed is 0.7 mm/stroke. If the maximum stroke length is 827 mm and allowable depth of cut is 0.4 mm for both of rough and finish cuts, what is the total machining time, in minutes ?
Calculate the machining time to drill four 20 mm diameter holes and one 50 mm diameter central hole in the flange as shown below. Take cutting speed 20 m/min, feed for 20 mm drill 0.2 mm/rev, and for 50 mm drill feed is 0.6 mm/rev, the point angle is 120°? VIVER 20xA 200 D100 SYLON 50
Turning Operation In a production turning operation, the foreman has decreed that a single pass must be completed on the cylindrical workpiece in 4.8 min. The piece is 400 mm long and 150 mm in diameter. Using a feed = 0.43 mm/rev and a depth of cut = 4.0 mm, what cutting speed must be used to meet this machining time requirement? Hint: Re-arrange the Tm equation to find v in m/min Tm= T.DO.L v.f 1.522
A shaper is operated at 120 cutting strokes per minute and is used to machine a work piece of 250 mm in length and 120 mm wide. Use a feed of 0.6 mm per stroke and a depth of cut of 6 mm. Calculate the total machining time to for machining the component. If the forward stroke is completed in 230°, calculate the percentage of the time when the tool is not contacting the work piece.
Taper turning is performed on a mild steel specimen, using the given data determine the following. of () Large diameter of the taper is 31.5 mm (ii) Spindle speed is 190 rpm, feed is 0.2 mm/rev & Depth of cut is 0.5 mm tion (ii) 1.5 minutes and 17.7 minutes are respective time required to complete one single taper turning operation and total time required to complete the taper turning operation Find (a) Cutting speed in m/minutes - (* (b) Taper Length in mm - (1 (c) Taper angle in degree