HA 10: m² RL am doing a AC DC 12 W Regulated power supply with 110 vrms and 60H s an input, and I need an output of 6v and 9 V. I have the designed Iready: the step-down transformer, Resistor as a current limiter to prote he Zener diode, a capacitor for the ripple voltage, and a 2 state switch ( when the switch is closed to the RL will give 9 V and when is closed to the will give 6V as an output). need some support with some calculations to find PIV for each diode // verage Power// some calculations in how to find the values for the esistors and capacitors to accomplish the desire output // and some alculations for the ripple voltage. Note: the Zener is regulated to 9v. know the RL>R to get the desire output.

HA 10: m² RL am doing a AC DC 12 W Regulated power supply with 110 vrms and 60H s an input, and I need an output of 6v and 9 V. I have the designed Iready: the step-down transformer, Resistor as a current limiter to prote he Zener diode, a capacitor for the ripple voltage, and a 2 state switch ( when the switch is closed to the RL will give 9 V and when is closed to the will give 6V as an output). need some support with some calculations to find PIV for each diode // verage Power// some calculations in how to find the values for the esistors and capacitors to accomplish the desire output // and some alculations for the ripple voltage. Note: the Zener is regulated to 9v. know the RL>R to get the desire output.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) IN4001 Ry OV 10k) D IN4001
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) D1 IN4001 R. V out OV 10 kN D2 IN4001 llle
The ripple factor for pure dc is Answer: For the given circuit below, it operates on a peak-to-peak input voltage of 390.1 V, F= 60 Hz household supply through a step-down transformer with turns N1 = 10 and N2 = 1. Silicon diodes are used with a 1 Kiloohms load. Determine the output peak voltage (in volts). D1, D2 AC Input Vsec (Source) .03 D4 Load O 27.31 O 18.11 O 13.93 O 20.91
What is the value of the average voltage at the output of the circuit in the figure, knowing that: Voltage at the transformer output is equal to 5 Vac and the four diodes are from the 1N4001 family.
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) D IN4001 R 10 kn IN4001
Design a DC power supply using FWR to perform the following requirements. Find V_dc, V_rms, V-ripple, PIV of the diode. draw the waveform of (V_in, V_out, L_in, I_load, V_diode and I_diode). Input voltage = 25 Transformer turn ratio 0.1 load resistance = 1k ohm Ripple factor = 0.025 Diode type =Si
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R1, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) D IN4001 R1 V out 10 kN D2 IN4001 allle
Consider the circuit shown in Figure Q7. The full-wave bridge rectifier is supplied from a transformer that has a secondary winding resistance of 52. When conducting, each diode has a forward voltage drop of 0.7 V, regardless of the current carried. D1 D4 240 V rms 50 Hz D2 D3 RL Figure Q7 (a) The transformer has a turn ratio of 10:1. Find the value of the load resistance, RL, if the peak voltage across the load is found to be 20.0 V. (b) For a load resistance of 50 2 and a transformer that gives a peak current in the load of 0.5 A, what is the power dissipated in the load? n:1
A three-phase rectifier is supplied by a 173.2-V rms line-to-line 60-Hz source. The RL load is a 100 resistor in series with a 15-mH inductor. Determine THD taking Is1 = 1.35
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R1, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) DI 14001 RL V onl O V 10 kN D2 IN4001 allle
Q5. For the following center tapped transformer, show the wave form across each half of the secondary winding and across R1, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) IN4001 R 10 ΚΩ I14001 Q6. Can we operate normal PN junction diode in breakdown region for longer duration? Give reason Q7. What is the specialty of Zener diode so as we can operate it in breakdown region for longer duration? Q8. What is the difference between Zener breakdown and Avalanche breakdown? Q9. Draw Zener regulator circuit to obtain regulated DC voltage 6.8 V. Considering input DC voltage in the range from 10V to 30V. Consider load resistance of 10KS. Q10. Determine maximum and minimum value of Zener current if value of series resistance is 1 K, load resistance is 2KN and input varies from 10V to 30V. Zener voltage is 5 V. Q11. What is LED? Q12. Which materials are used in manufacturing of LEDS?…
For the given circuit below, a step down transformer gives an RMS voitage of 230 V/ 12-0-12 V with a load resistance of 22 Kiloohms. Assume Silicon diodes are used. Determine the Peak Inverse Voltage of the diode. O 33.94 O 26.83 O 16.97 O 21.17 A silicon diode in a half-wave rectifier has a barrier potential of 0.7 V. This has the effect of reducing the peak input voltage by 0.7 V. increasing the peak input voltage by 0.7v. no effect. increasing the peak output voltage by 0.7 V. Next nane