B/ A 50 KVA, 2300/230 V, 60 11z transformer has a high voltage 0.6502 and a low-voltage winding resistance of 0.0065 2. Labora following results: Open circuit test: V = 230 V, 1-5.7A, P = 190 W Short circuit test: V-41.5 V, 1-21.7 A, P-No wattmeter was used. (2) Compute the value of primary voltage needed to give rated secc transformer is connected as a step-up one and is delivering 50 KVA

B/ A 50 KVA, 2300/230 V, 60 11z transformer has a high voltage 0.6502 and a low-voltage winding resistance of 0.0065 2. Labora following results: Open circuit test: V = 230 V, 1-5.7A, P = 190 W Short circuit test: V-41.5 V, 1-21.7 A, P-No wattmeter was used. (2) Compute the value of primary voltage needed to give rated secc transformer is connected as a step-up one and is delivering 50 KVA

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.33P: Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage...

See similar textbooks

Similar questions

For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the rated voltage on the other winding? (a) Yes (b) No
Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in , place the polarity marks, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a, b, and c such that VAN is 90 out of phase with Va for positive sequence.
The symbol shown is a(n) a. iron core transformer. b. auto transformer. c. current transformer. d. air core transformer.
Answer only please The resistance of a transformer winding is 0.25 ohm at 25oC. When operating at full load, the temperature of the winding is 75oC. The temperature coefficient of resistance for copper at 0oC is 0.00427 per oC. What is the winding resistance at full load? a. 0.512 ohm b. 0.315 ohm c. 0.298 ohm d. 0.271 ohm
In a load test on transformer the no load voltage is 240V. The terminal voltage drop is 225V on resistive load condition. The primary voltage of transformer is 350V. The primary and secondary currents are 0.45A and 0.671A. What is the efficiency of the transformer? O a. 68% O b. 95.85% O c. 64% O d. 43.19%
In the circuit in Figure 2, the capacitor connected to the a-b terminals of the transformer anda circuit consisting of resistance is defined as a load circuit. a)Find the average power spent by the load circuit? b) How much of the average power calculated in a) by the resistance in the load circuit and how muchspent by the capacitor? Comment on the results obtained?
A voltage transformer in Figure 8 has 1,500 turns of wire on its primary winding and 500 turns of wire for its secondary winding. What will be the turns ratio, a of the transformer. If 240 volts is applied to the primary winding, what will be the resulting secondary voltage. And if a 400 n resistor is connected to the secondary winding, what are the values of current Is and Ip. primary Vp Transformer Core NF Ns Figure 8 secondary Vs
Question:4 A Step-down transformer is given and calculate 5:1 120 V 60 Hz V2 i k2 i. Peak load and D.C. load voltage ii. D.C. Current
The voltage per winding of the 220V/12V, 60 Hz single phase core transformer is 1V. If the maximum flux density in the core is 1.5 T, the cross-sectional area of the core in cm 2 is equal to which of the following. 0.0030 25 60 50 0.0050 0.0025 0.0060 30
In the circuit in Figure 2, the capacitor connected to the a-b terminals of the transformer anda circuit consisting of resistance is defined as a load circuit. Find the average power spent by the load circuit?
a)The voltage per winding of 220V/12V, 60 Hz single phase core transformer is 1V. If the maximum flux density in the core is 1.5 T, which of the following is the cross-sectional area of the core in cm²? 0.0030 0.0060 30 25 50 0.0050 0.0025 60 b) The voltage per winding of 220V/12V, 50 Hz single phase core transformer is 2V. If the maximum flux density in the core is 1.5 T, which of the following is the cross-sectional area of the core in cm²? 0.0030 0.0060 30 25 60 0.0050 0.0025 50
A single phase transformer is required to step down the voltage from 1100 V to 230 V at 50 Hz. The maximum value of the flux in the core is 0.20 Wb. Determine the number of turns in the winding in both sides.