How many 8-mm diameter rivets is needed to fasten member DC to the gusset plate at Cif the member DC has thickness of 8 mm and the working stresses are 15 MPa for shear in the rivets and 20 MPa for bearing due to the rivets. Express your answer to the nearest whole number being the safe value of the rivets to be used.* -3m 40 AN 35 AN

How many 8-mm diameter rivets is needed to fasten member DC to the gusset plate at Cif the member DC has thickness of 8 mm and the working stresses are 15 MPa for shear in the rivets and 20 MPa for bearing due to the rivets. Express your answer to the nearest whole number being the safe value of the rivets to be used.* -3m 40 AN 35 AN

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.13P: Two steel rods are welded together (see figure): the seam is oriented at angle ? = 50°. The stresses...

See similar textbooks

Similar questions

6. A PIPE CARRY|NG STE AM AT 3.5 MPa HAS AN OUTSIDE DIAMETER OF 450 mm AND A WALL THICKNESS OF 10 mm. A GASKET IS INSERTED BETWEEN THE FLANGE AT ONE END OF THE PIPE AND A FLAT PLATE USED TO CAP THE END. HOW MANY 40 mm- DIAMETER BOLTS MUST BE USED TO HOLD THE CAP ON IF THE ALLOWABLE STRESS IN THE BOLTS IS 105 MPa, OF WHICH 55 MPa IS THE INITIAL STRESS ? WNHAT CIRCUMFERENTIAL IN THE PIPE ? TO TIGHTEN THE BOLT INITIALLY, AND WHAT WILL STRESS IS DEVELOP WHY IS IT NECE SSARY HAPPEN IF THE STEAM PRESSURE SHOULD CAUSE THE STRESS IN THE BOLTS TO BE TWICE THE VALUE OF THE INITIAL STRESS?
1cm t1 (cm) P 3,2 cm t2 (cm) t1 (cm) 1 cm 20 cm Ь (ст) P = 20t %3D Dp=1,6 cm
Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. Draw appropriate FBDs showing how the internal forces were determined. A square bar (side length = 50 mm) is welded to a fixed supporting slab. A 30-mm diameter pin is inserted in the bar. When the loading shown is applied, determine the following: a. maximum normal stress in the bar (MPa) and bearing stress between the pin and the bar (MPa)b. stress in the weld between the bar and the supporting slab (MPa)c. shear stress in the pin (MPa) and shear stress in the bar (MPa)
A cast Aluminum crlinder o f a Portable hodrawlic 208 Mm in diameter The 16,8 N/mm2 by gauge riveter is Pressure. of The fluid is Determine Sui table thicknesS of the inder wall assuming that the Yield Point stress 442 N/mm2 And factor of safety of 6.2 Calculate. the tangential and radial streses middle radius and at the inner outer surface.
A flanged bolt coupling connects shafts on each side. It consists of 8- 19 mm diameter bolts on a bolt circle of 300 mm and 6 – 12 mm diameter bolt on a bolt circle of 230 mm. Determine the stress on BOLT CIRCLE land the stress on BOLT CIRCLE 2 (in MPa) due to a torque of 20 KN-m. (in MPa)
estion 11 62.5 mm Кey 55° The cast iron block with cross-sectional dimensions of 62.5 mm by 62.5 mm consists of two pieces. The pieces are prevented from sliding along the 55° inclined joint by the steel key, which is 62.5 mm long. The working stresses are 275 MPa for cast iron in bearing and 345 MPa for the key in shear. If the block is loaded with P = 256 kN, calculate the required dimension "h" of the key. Write your final answer in 2 decimal places with the unit of mm.
3. Calculate the bearing stress and shear stress between the pin and each bracket of a clevis joint. Assume pin diameter of 10 mm, 40 mm wide gap link, 12 mm thick bracket, and 3550N tensile load. Draw a free body diagram (geometry & forces) Identify stress plane Calculate stress and write it (with appropriate units) in the outlined box
Find the smallest and safestd of the link as shown on the figure, if the working stress is equal to your SN mPa. FN kN FN kN
Problem 2 only, solve carefully, include the units and dra the diagram. Thanks! A 3/4 inch diameter rivet is used to fastened two 25 mm thick plate. If the shearing stress of rivet is 80 Mpa, A. What tensile force applied each plate to shear the bolt, pounds?B. What bearing stress that the bolt can withstand, MPA
Two steel rods are welded together (see figure): the seam is oriented at angle ? = 50°. The stresses on the rotated element are sx1=10 ksi, sy1= -12 ksi, and tx1y1= -5 ksi. Find the state of plane stress on the clement if it is rotated clockwise to align the x3 axis with the longitudinal axis of the rods.
Tyx 3MP 8MPd 45 2MPA Determine the two principal stresses in MPd
down by iS 12 mm wide EsSembled 4 A duralumn Calinder head is held deun by Steel bolt each 65 mm whieh fung. Just eind belt is tightened thread Compressed inside when eech made tight end ie then turn (e eg linder head a tube 12 eudside by. Fur Her Luarler ef l-5 mm). The Considered Piteh Cen be diameter diemeter. Determine the stresses in Hhe eund 25 mm Steel eind dusalumin. Take E = Luo Ida Steel %3D Cnd 684N/mm". dur