in the pulley system and the diagram above, assume that the bearings at oh and C are properly aligned and smooth and that T2 =30 N all dimensions in millimeters and the belt tensions are all tangential to the pulleys a. If the shaft runs at a constant speed, determine the tension T1 b draw a free body diagram of the shaft and determine the reactions at bearing sea in terms of the components along the Y and Z axis. Assume neither bearing and oh or see produces an axial thrust

in the pulley system and the diagram above, assume that the bearings at oh and C are properly aligned and smooth and that T2 =30 N all dimensions in millimeters and the belt tensions are all tangential to the pulleys a. If the shaft runs at a constant speed, determine the tension T1 b draw a free body diagram of the shaft and determine the reactions at bearing sea in terms of the components along the Y and Z axis. Assume neither bearing and oh or see produces an axial thrust

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.2P: 5.2 Evaluate the Prandtl number from the following data: , .

See similar textbooks

Similar questions

Mechanical Engineering xyz= 703 Stress, ksi (log) 72 49 35 28 10³ 8 x 10³1 10¹ 401 X 8't 49 ksi 10 ksi 401 X 9'1 35 ksi 28 ksi 105 Cycles (log) 106 19.8 The provided S-N curve shows the fatigue strength of a ferrous component with unknown geometry. 107 Given the following duty record, how much life is consumed at each stress level? 60 ksi 500 cycles 2000 cycles (600 000 + XYZ*100) cycles (15000 + XYZ) cycles 40000 cycles
Q3/ Draw the front section of the figure (2)? RIO p10 54 $82 44 $56 76 RI14 12 FROM CENTRE OF Bss $12 19 $86 50 24 140 32 انصاف اقطار الاقواس غير المؤشرة R3| $70 Figure (2)
a)The bore of each cylinder in a six-cylinder car engine is 45 mm and the stroke for each piston is 125 mm. calculate the cubic capacity of the engine in cubic centimetres (cm3 ); and calculate the clearance volume per cylinder for a compression ratio, r, of 8.75. b) The bore of each cylinder in a four-cylinder four-stroke internal combustion engine is 38 mm and the stroke of each piston is 165 mm. During testing, the engine runs at 180 revolutions per minute (rpm) with a pressure-volume indicator diagram showing a mean net area of 3.4 cm2 and a diagram length of 1.2 cm. The pressure scale on the indictor diagram is set to 150 kN/m2 per cm. Calculate the mean effective pressure (m.e.p) and the indicated power developed by this four-cylinder four-stroke engine.
Question 9 Answer the following questions. Show your work on a separate paper. Round your responses to 3 significant figures. Include appropriate units. Provide magnitude and direction where appropriate. The 4.5 Mg truck shown below collides with the 1.75 Mg car. After the collision, they move forward together. Answer the following questions. 30 km/h 10 km/h 38) What is the combined velocity of the truck and the car just after impact? Show your work. Solution Units Direction 3b) What is the coefficient of restitution of the impact? Show your work or justify your response on a separate piece of paper. Solution Units
I’m struggling with questions q1 2 3 4 5
Bottles for room spray are supposed to weigh exactly 16 oz. Inspectors want to develop process control charts. They take o7 boxes of five bottles each and weigh them. They obtain the following data. The mean weights of each of the 07 samples are 14.6,16.5,18.1,13.2,16,15.9, and 14.8 respectively. Likewise, the range values for the each of 07 samples are o.7,0.5, 0.4,0.2,0.4,0.5, and o.9 respectively. Ebr the X-bar charts and R-charts, the Parameters, A2, D3 and D4 are respectively.
1. solve step by step and show proper conversion and cancellation of units.
This FBD is considered to solve the problem. 0.45 m 0.45m P 0.75 m 1.35 m 1.05 m N ii) Choose the assumption made for using this FBD. O a. The crate is in equilibrium. O b. The crate is slipping. O c. The crate is tipping. O d. The crate is moving.
a) A locomotive is travelling at 35 m/s up an incline of 0.006 radians when the engine cuts out. How far will the locomotive travel up the incline before coming to rest? Assume there are no frictional losses, no energy input from the engine, and take acceleration due to gravity to be 9.81 m/s². Give your answer in km. Round your answer to 4 significant figures. b) What is the speed (in m/s) of the locomotive after it has travelled a distance 5.83 km? Round your answer to 3 significant figures.
Round off the following number to three significant figures:68.534s
How many significant figures are in number? 1.563300 x 10^11 m
Please use different values. This answer you already gave me for a similar question. These values I choose myself and made them up.