In the table below for E106, which of the following is the amount of heat gained by the calorimeter? TRIAL 1 Metal Specimen 1 Determining the Specific Heat of Metal Specimen Mass of calorimeter, me Mass of calorimeter with water Mass of water, mix Mass of metal specimen, mm Initial temperature of metal, tom Initial temperature of calorimeter, toc Initial temperature of water, tow Final temperature of the mixture, tmix Specific Heat of Water cw Specific Heat of calorimeter c Experimental specific heat of metal, cm Actual specific heat of metal, cm Percentage Error 150.0 g 225.0 g 8 100.0 g 100°C 20.0°C 20.0°C 26.5°C 1.0000 çal/gC 0.2174 cal/gC cal/gC 0.0917 cal/gC

In the table below for E106, which of the following is the amount of heat gained by the calorimeter? TRIAL 1 Metal Specimen 1 Determining the Specific Heat of Metal Specimen Mass of calorimeter, me Mass of calorimeter with water Mass of water, mix Mass of metal specimen, mm Initial temperature of metal, tom Initial temperature of calorimeter, toc Initial temperature of water, tow Final temperature of the mixture, tmix Specific Heat of Water cw Specific Heat of calorimeter c Experimental specific heat of metal, cm Actual specific heat of metal, cm Percentage Error 150.0 g 225.0 g 8 100.0 g 100°C 20.0°C 20.0°C 26.5°C 1.0000 çal/gC 0.2174 cal/gC cal/gC 0.0917 cal/gC

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter17: Energy In Thermal Processes: The First Law Of Thermodynamics

Section: Chapter Questions

Problem 7OQ

See similar textbooks

Similar questions

Suppose a gasfilled incandescent light bulb is manufactured so that the gas inside the bulb is at atmospheric pressure when the bulb has a temperature of 20.0C. (a) Find the gauge pressure inside such a bulb when it is hot, assuming its average temperature is 60.0C (an approximation) and neglecting any change in volume due to thermal expansion or gas leaks. (b) The actual final pressure for the light bulb will be less than calculated in part (a) because the glass bulb will expand. What will the actual final pressure be, taking this into account? Is this a negligible difference?
In the table below for E106, which of the following is the amount of heat lost by the metal specimen when dropped in the calorimeter with water? TRIAL 1 Determining the Specific Heat of Metal Specimen Metal Specimen 1 Mass of calorimeter, me Mass of calorimeter with water Mass of water, mi Mass of metal specimen, mm Initial temperature of metal, tom Initial temperature of calorimeter, toc Initial temperature of water, tow Final temperature of the mixture, tmix Specific Heat of Water cw Specific Heat of calorimeter ce Experimental specific heat of metal, cm Actual specific heat of metal, cm Percentage Error O 699 cal O 212 cal O 675 cal O 488 cal 150.0 g 225.0 g 8 100.0 g 100°C 20.0°C 20.0°C 26.5°C 1.0000 çal/gC 0.2174 cal/gC cal/gC 0.0917 cal/gC %
What is/are the differences between heat and temperature? (You may have more than 1 answer) POSSIBLE PO volume O unit of measurement can be determined in hot objects O can be determined in cold objects 1.
Q1: An electric heater contains 40 liter of water initially at a mean temperature of 15°C. 0.25 kWh is supplied to the water by the heater. Assuming no heat losses, what is the final mean temperature of the water? Note that 4185 J taking to rise the temperature of 1 liter of water 1°C.
sics 2 (Engineering) / My courses/ PHYS1211 / Lab Experiments / Experiment 3: Lab Report (Thermal Conductivity of Materia The thermal conductivity of a material depends only on the type of and is a constant. of If a material is having low thermal conductivity then, the material is a good thermal tion Of the given materials, brass and steel, is a better conductor, as its value is higher. Finish attempt. page
Why is it important for the thermometer to be fully immersed in the water but does not touch the bottom of the inner vessel in doing the experiment for latent heat of fusion of ice? * The thermometer will be damaged if it will touch the inner vessel of the calorimeter. The thermometer in contact with the bottom of the vessel will cause the final temperature to be too warm and gives an experimental value of the latent heat of fusion that is too low To have an equilibrium temperature of too high or too low.
Question 1 For the "Specific Heat of Solid" experiment the following data table are found. Using the value from the table, calculate the specific heats [in J/(kg-°C)] of the Copper samples. Mass of metal sample [Copper] mm = 0.3 Mass of calorimeter cup while empty m. = 0.1082 [m] = 0.3357 Mass of cup with cold water in it Mass of cold water m, = 0.2275 Cw = 4186 J/kg-oC C = 1510 J/kg-oC 4186 Specific heat of water Specific heat of cup Temperature of cold water Final temperature 1510 Tw 21 32 Temperature of metal Tm 80 0.002 402 852 31494 None of these Question A Moving to another question will save this response ENC h 45
31 TanKSSMF4010T the water after being heated are recorded. The following figure shows the graph of O against obtained. m e CC) Graph of 0 against m 34 33 32 30 29 28 27 (kg-) 0.7 26 0.1 0.2 0.3 0.4 0.5 0.6
The ratio A. B. C. D. 6* A OB O D thermal capacity of a sample of copper specific heat capacity of copper does not have any unit. has unit J kg-¹ K-¹ has unit J kg-¹. has unit kg.
Problem 1- Heat Transfer How thick would the glass panes on a double-glazed window (air gap = 2mm) have to be to make the double-glazed resistance to heat transfer equal to the resistance to heat transfer provided by a single pane of glass of thickness 50mm. The thermal conductivity of air and glass are 0.05W/m°C and 0.9W/m°C respectively.
A calorimeter does not involve measurement of temperature. True or False? a) True b) False
Q3/ a/ ITRNACE On= 80MW Wnet.out НЕ OL = 50 MW RIVER Determine thermal efficiency