Neglect stress concentrations at the corners of the tubes in the following problems. Two identical metal sheets are formed into tubes with the circular and square cross sections shown. If the s applied to each tube, determine the ratios (a) Tcircle/Tsquare of the shear stresses; and (b) Ocircle/esquare o twist. Q

Neglect stress concentrations at the corners of the tubes in the following problems. Two identical metal sheets are formed into tubes with the circular and square cross sections shown. If the s applied to each tube, determine the ratios (a) Tcircle/Tsquare of the shear stresses; and (b) Ocircle/esquare o twist. Q

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2. Determine the shearing stress in each of the four walls of a portion of a structural aluminum tubing when it is subjected to a torque of 3 kN-m assuming a uniform wall thickness of 4mm. A ( 51 ) mm В 100 mm 100 mm C D ( 51 ) mm
The compound shaft consists of bronze and steel segments, both having 120-mm diameters. If the torque T causes a maximum shear stress of 100 MPa in the bronze segment, determine the magnitude of T (in Nm). Use G = 83 GPa for steel and G = 35 GPa for bronze. Bronze Steel 45 m 3.5m リト

2 0:0. 5.pdf → الامتحان اليومي الثاني )ميكانيك المواد I I( Q: For the state of stress shown in fig. below. Determine the principle stress and the max. shearing stress .show all results on complete sketches of differential element. 60 MPa 80 MPa 80 MPa 20 MPa 20 MPa 60 MPa ريفان
4. Part AB of the bar has a solid circular cross section and part BC has a hollow circular cross section. The bar is fixed at both ends and a 150-in-kip axial torque is applied at B. Suppose that you want to decrease the weight of the bar by increasing the inside diameter of part B. The bar is made of material that will safely support a pure shear stress of 10 ksi. Based on this criterion, what is the largest safe value of the inside diameter? 4 in 2 in 150 in-kip A -14 in 7 in
Q.2) A rigid bar ACD is supported by two circular steel (E= 30x10° psi) rods AB & DE and a pin support at C. Bar ACD was horizontal prior to the application of load P. The tensile strain measured in rod AB after the application of the load is ɛ1= 0.003. Determine the rotation 0 of the bar ACD and the normal strain in rod DE. Also calculate the value of load P for these deformations. The diameters of rod AB and DE are 1.5 in. and 2 in, respectively. P - 4 ft 4 ft- 6 ft A Rigid (2) 6 ft 8 ft (1) E В
1. A steel shaft is to be manufactured either as a solid circular bar or as a circular tube (Fig. 3-12). The shaft is required to transmit a torque of 1200 Nm without exceeding an allowable shear stress of 40 MPa nor an allowable rate of twist of 0.75%m. (The shear modulus of elasticity of the steel is 78 GPa.) a) Determine the required diameter d0 of the solid shaft. b) Determine the required outer diameter d2 of the hollow shaft if the thickness t of the shaft is specified as one-tenth of the outer diameter. c) Determine the ratio of diameters (that is, the ratio d2/d0) and the ratio of the weights of the hollow and solid shafts.
A uniform steel shaft has a diameter of 50 mm is fixed at ends A and B. The shear modulus of steel is 75 GPa.d) Calculate the maximum shear stress in the system in MPa. You will have to look at each individual piece of the system, so clearly indicate which segment has the maximum stress.[Ans. to check: τmax = 8.15 MPa]e) Calculate the total rotation of the shaft at point C in radians.
Pin-connected rigid bars AB, BC, and CD are initially held in the positions shown by taut wires (1) and (2). The bar lengths are a = 36 ft and b = 27 ft. Joint Cis given a horizontal displacement of 5.7 in. to the right. (Note that this displacement causes both joints B and C to move to the right and slightly downward.) What is the change in the average normal strain in wire (1) after the displacement? B (1), a (2) Answer: = i (0)
Pin-connected rigid bars AB, BC, and CD are initially held in the positions shown by taut wires (1) and (2). The bar lengths are a = 28 ft and b = 21 ft. Joint C is given a horizontal displacement of 3.0 in. to the right. (Note that this displacement causes both joints B and C to move to the right and slightly downward.) What is the change in the average normal strain in wire (1) after the displacement?
Pin-connected rigid bars AB, BC, and CD are initially held in the positions shown by taut wires (1) and (2). The bar lengths are a = 8 ft and b = 6 ft. Joint C is given a horizontal displacement of 4.6 in. to the right. (Note that this displacement causes both joints B and C to move to the right and slightly downward.) What is the change in the average normal strain in wire (1) after the displacement? b В (1) a (2) A D
Q.3)A rigid bar DAB is supported by two circular rods and a pin as shown below. The member at D is an aluminum (E = 70 GPa) rod, and the member BC is a steel (E = 200 GPa) rod. The diameter of the aluminum rod is 10 mm and that of the steel rod is 5 mm. Calculate the average normal stresses in the steel and aluminum rods due to the applied load of 650 N. Also, determine the rotation of the rigid bar DAB about the pin A, and the horizontal displacement of point D. 200 mm A B 150 mm 100 mm 150 mm 650 N DI 50 mm
Pin-connected rigid bars AB, BC, and CD are initially held in the positions shown by taut wires (1) and (2). The bar lengths are a = 8 ft and b = 6 ft. Joint Cis given a horizontal displacement of 7.0 in. to the right. (Note that this displacement causes both joints B and C to move to the right and slightly downward.) What is the change in the average normal strain in wire (1) after the displacement? b В (1), (2) D Answer: E = με